Actions

INCA Station Kit Restore Factory Defaults: Difference between revisions

From Zenitel Wiki
No edit summary
 
(10 intermediate revisions by 3 users not shown)
Line 1: Line 1:
{{APS}}
This procedure is applicable for:
This procedure is applicable for:
* IP Substation Kit - [[IP Substation Kit - 1008090200|1008090200]]
* IP Master Station Kit [[IP Master Station Kit - 1008093000|100809300]]
* IP Master Station Kit [[IP Master Station Kit - 1008093000|100809300]]
* IP Substation Kit - [[IP Substation Kit - 1008090200|1008090200]]
 
* [[IP Heavy Duty Station|IP Heavy Duty station 1008072xx0]]
<div style="text-align:left;"> <youtube width="300" height="180">WP9m-DG0hMU</youtube>  </div>




The Factory Default can be either set to Static IP 169.254.1.100 or activate DHCP.
The unit can be set to use either '''Static IP''' or '''DHCP'''. On the rear side of the PCB there is a red status LED. Pay attention to this LED during the restore procedure:


Connect a push button ('''KEY1''') between pin 1 and 4 on the P4 connector.
[[File:Load Defaults without KEY.PNG|right|thumb|800px|Connect a push button between pins 1 and 4]]


[[File:Load Defaults without KEY.PNG|left]]
== Procedure ==
<br style="clear:both;" />
# Connect a push button ('''KEY1''') between pin 1 and 4 on the P4 connector.
# While pressing the button, power up the station kit and keep the button pressed.
# Release the button '''after exactly 2 flashes''' of the LED.
# Let the LED flash for '''exactly 2 more times''' (Static IP) or '''exactly 4 more times''' (DHCP), then press the button again.
# Keep the button pressed until the LED '''flashes fast 2 times''' (Static IP) or '''flashes fast 4 times''' (DHCP) indicating a successful reset.
# Release the button and the station will restart with the factory default settings.


== Restore with Static IP ==
# While pressing the button, power up the station kit.
# When the station kit LED starts blinking, release the button '''after exactly 2 blinks'''.
# Let the LED blink for '''exactly 2 more times''', then press the button again.
# Keep the button pressed until the LED '''blinks fast 2 times''' indicating a successful reset with static IP.
# Release the button and the station kit will restart with the factory default settings.


Factory default values:
== Factory default values ==
*Station Mode: '''Pulse'''
*Station Mode: '''Pulse'''
*Station IP address: '''169.254.1.100'''
*Station IP address: '''169.254.1.100''' or '''DHCP'''
*Username: '''admin'''
*Username: '''admin'''
*Password: '''alphaadmin'''
*Password: '''alphaadmin'''


* Software 01.06 and earlier: '''ADMIN/alphacom''')
== Restore with Activated DHCP ==
The DHCP option is available from software version 01.07.
# While pressing the button, power up the station kit.
# When the station kit LED starts blinking, release the button '''after exactly 2 blinks'''.
# Let the LED blink for '''exactly 4 more times''', then press the button again.
# Keep the button pressed until the LED '''blinks fast 4 times''' indicating a successful reset with activated DHCP.
# Release the button and the station kit will restart with the factory default settings.
{| class="wikitable"
!style="background:#ffdead" colspan="2"|Factory default values
|-
| Station Mode || align=center | '''Pulse'''
|-
| Station IP address || align=center | '''determined by DHCP server'''
|-
| AlphaCom IP address || align=center | '''169.254.1.5'''
|-
| Username* || align=center | '''admin'''
|-
| Password* || align=center | '''alphaadmin'''
|-
|}
* Software 01.06 and earlier: '''ADMIN/alphacom''')


[[Category: INCA - Restore Factory Defaults and Software Upgrade]]
[[Category: INCA - Restore Factory Defaults and Software Upgrade]]

Latest revision as of 13:25, 15 May 2018

APS.png

This procedure is applicable for:


The unit can be set to use either Static IP or DHCP. On the rear side of the PCB there is a red status LED. Pay attention to this LED during the restore procedure:

Connect a push button between pins 1 and 4

Procedure

  1. Connect a push button (KEY1) between pin 1 and 4 on the P4 connector.
  2. While pressing the button, power up the station kit and keep the button pressed.
  3. Release the button after exactly 2 flashes of the LED.
  4. Let the LED flash for exactly 2 more times (Static IP) or exactly 4 more times (DHCP), then press the button again.
  5. Keep the button pressed until the LED flashes fast 2 times (Static IP) or flashes fast 4 times (DHCP) indicating a successful reset.
  6. Release the button and the station will restart with the factory default settings.


Factory default values

  • Station Mode: Pulse
  • Station IP address: 169.254.1.100 or DHCP
  • Username: admin
  • Password: alphaadmin
Retrieved from "https://wiki.zenitel.com/w/index.php?title=INCA_Station_Kit_Restore_Factory_Defaults&oldid=185998"
MediaWiki spam blocked by CleanTalk.