AlphaVision - How to get started

This product is discontinued!

This article gives step-by-step instructions how to get started with AlphaVision. Main configuration steps are:

• AlphaWeb: Enable TCP port 55010
• AlphaPro: Activate ACDP link and Device 64
• AlphaVision: Configure communication parameters (AVCMSetup) and select 'Operator station'

AlphaVision - Example configuration

AlphaWeb

• In System Configuration -> Filters, enable TCP port 55010 on the ethernet port used for AlphaVision.

AlphaPro

• In Exchange & System -> Serial ports, activate a communication port to be used for AlphaVision. Select one of the seven ACDP Links, and set the following parameters:

• • Port Type: TCP/IP Server
  • Link Type: Stentofon MultiDrop Master - Reserved
  • Broadcast: Enabled
  • Destination: AlphaVision (any text)
  • Port: 55010
  • Keep Alive: Enabled

AlphaPro: Serial Ports setting

• In Exchange & System -> Devices, scroll down to device 64 and set:

• • Device type: Operator (passive)
  • Data (ACDP link): select the link which was configured in the Serial Ports window

AlphaPro: Device settings

AlphaVision

Setup

• Download and install AlphaVision on a PC. Latest software version is available on request.
• Start the 'AVCMSetup' program (Windows XP: Start-> All Programs -> AlphaVision: AVCMSetup). Set:
  • Communiation Type: IP
  • AC E IP address: The IP address of the AlphaCom
  • Normally one can leave the other parameters as is. Press OK to close the window.

AlphaVision: AVCMSetup

• Start the AlphaVision program. Username = service, password = service (Supervisor login). The 'Message Window' at the bottom of the screen should show "Run Mode", and a green "eye" should appear at the bottom right corner of the PC, indicating the the communication between AlphaVision and AlphaCom is OK.
• Select the 'System Tree' tab. AlphaVision will automatically detect stations as they are being used, and they will show up in the System Tree. An easy way to automatically detect all stations is to dial the code 7885 (Tone Test) from a SuperUser. Now all stations will detected one by one. (Initially only Station 102 will appear in the System Tree, as this is the default operator station. Double click on station 102 to open the tree to see all stations).
• Assign an 'Operator station' to AlphaVision by selecting Configuration -> Options -> Systems tab. By default station 102 in node 1 is set as operator station if found, and no other station is defined.

AlphaVision screenshot - Communication OK and stations are detected and shown in the System Tree

Operation

When a Call Request is sent to the 'Operator Station' (e.g. a station dials 623 + 102), the call will appear in the Call Request list, and an "Accept" button will appear. The call is answered by clicking the "Accept" button, or by double clicking the station in the call request list. During conversation, a "Cancel" button will appear to terminate the conversation.

Map and Icons

In 'Configuration -> Maps' you can create or import a map. From the 'System Tree' you can drag stations and drop them on to the map, and they will appear as icons on the map.

When the icons are placed on the map, they will automatically show the status of the station, based on data received from the AlphaCom:

• Idle
• Connected
• Call Request (low priority)
• Call Request (high priority)
• Station Error

The first four statuses are reported automatically by the AlphaCom, but to show Station Errors one have to add one event in AlphaPro:

In Exchange & System > Events, Insert an event with the following properties:

Create this event to show "Station Down" on the icon

Action commands:

@01FF M7C06 %1.REF U%chg(1,0)

Where 01 is the node number of the AlphaCom.

Related articles

• AlphaVision (Main article)
• AlphaVision - Single Click to Call