Latest revision as of 11:39, 15 August 2022

The Mediant 600 has the capability to transcode a SIP call from e.g. G711µ-law to G729. Here are some examples using the Mediant 600 to transcode G711µ-law to G729.

The examples shown are between:

AlphaCom XE and Cisco Call Manager
AlphaCom XE and AudioCodes MP-114/118
AlphaCom XE and Mobile VoIP GSM Gateway MV-370

Configuration example

1 AlphaCom Configuration
2 Mediant 600 Configuration
3 Configuration of Mediant 600 with SIP Account as End Point
4 AudioCodes MP-114/118 Configuration
- 4.1 SIP Parameters
- 4.2 Audio Codec
5 Cisco Call Manager Configuration
- 5.1 Configure a Region
- 5.2 Configure a SIP Trunk
6 Mobile VoIP GSM Gateway MV-370
- 6.1 SIP settings
- 6.2 Codec settings

AlphaCom Configuration

How to set up a SIP Trunk in the AlphaCom is described here: SIP trunk node - configuration

Mediant 600 Configuration

A license SIP to SIP Mediation and Routing Application (SW/IP2IP/15) is required. With this license, the Mediant600 has 30 active Media Channels that can support 15 transcoding simultane sessions.

Restore to factory default settings

Reset Button

With a paper clip, press and hold down the Reset button (located on the CPU Module) for at least 12 seconds (no more than 25 seconds)
The device restores to factory default settings

Access to the embedded web server

Home Page

The default Network parameter of the Mediant 600:

IP Adress : 10.1.10.10
Subnet Mask : 255.255.0.0
Default Gateway : 0.0.0.0

Connect your PC directly to the device, using an Ethernet Crossover cable

Before the PC can access to the Mediant 600, the IP address of the PC must be changed to match the same subnet (e.g 10.1.10.11)

To access the embedded web server, start your internet browser (e.g. Internet Explorer) and in the address field enter 10.1.10.10

You will be prompted for a username and password (default):

Username: Admin
Password: Admin

The Home Page page should now be displayed

Note: For the rest of configuration used the tree menu in Full mode

IP Configuration

Initial configuration

RETURN TO THIS

IP Settings

In the "IP Settings" page (Configuration tab -> Network Settings menu -> IP Settings page) enter :

IP Adress
Subnet Mask
Default Gateway
Click "Submit" to apply the changes

The IP address is immediately changed when pressing Submit, but it is not permanently stored

Without resetting or powering off the device, you need to log on to the Gateway using its new IP address in order to Burn the new IP address to flash:

Disconnect the PC from the Gateway
Connect the Gateway and PC to the LAN. The PC and Gateway must be on the same sub-net
Restore the PC’s IP address and subnet mask to what they originally were, and re-access the Gateway using the new assigned IP address
Click "Burn" to permanently apply the changes

Add Software Upgrade Key

The license for SIP IP2IP must be uploaded as a Software Upgrade Key.

Software Upgrade Key

In the "Software Upgrade Key Status" page (Management tab -> Software Update menu -> Software Upgrade Key page):

Enter the license key in the "Add a Software Upgrade Key" field
Click "Add Key"
Burn
Reset the device (Device Action -> Reset -> Reset)

Enable IP-to-IP Capabilities

Applications Enabling

In the "Applications Enabling" page (Configuration tab -> Protocol Configuration menu -> Applications Enabling page):

From the "Enable IP2IP Application" drop-down list, select "Enable"
Submit & Burn
Wait the next step for Reset the device

Number of Media Channels

IP Media Settings

In the "IP Media Settings" page (Configuration tab -> Media Settings menu -> IP Media Settings page):

In the "Number of Media Channeles" field, enter the required number of media channels: 30 (maximum capacity of Mediant 600 is 60)
Submit & Burn
Reset the device (Device Action -> Reset -> Reset)

Proxy Sets Table

These "Proxy Sets" are later assigned to "IP Groups" Note that the "Proxy Set" represents the actual destination to which the call is routed

In the "Proxy Sets Table" page (Configuration tab -> Protocol Configuration menu -> Proxies,Registration,IP Groups submenu -> Proxy Sets Table page):

Proxy Set ID1

Proxy Set ID#1 for AlpahCom XE

From the "Proxy Set ID" drop-down list, select "1"
In the "Proxy Address" column, enter the IP address of the AlphaCom
From the "Transport Type" drop-down list corresponding to the IP address entered above, select "UDP"
Submit

Proxy Set ID2

Proxy Set ID#2 for MP-114

From the "Proxy Set ID" drop-down list, select "2"
In the "Proxy Address" column, enter the IP address of the MP-114
From the "Transport Type" drop-down list corresponding to the IP address entered above, select "UDP"
Submit & Burn

IP Group Table

These "IP Groups" are later used by the device for routing calls

In the "IP Group Table" page (Configuration tab -> Protocol Configuration menu -> Proxies,Registration,IP Groups submenu -> IP Group Table page):

IP Group 1

IP Group #1 for AlpahCom XE

From the "Index" drop-down list, select "1"
In the "Description" field, type an arbitrary name for the IP Group (e.g. AlphaCom)
From the "Proxy Set ID" drop-down list, select "1" (For this "IP Group" communicate with the "Proxy Set" of the AlphaCom)
In the "SIP Group Name" field, enter the IP Adress sent in the SIP Request From/To headers for this IP Group (AlphaCom's IP Adress)
Contact User = name that is sent in the SIP Request contact header for this IP Group (e.g. AXE)
From the "IP Profile ID" drop-down list, select "1" (the IP Profile is configured later)
Submit

IP Group 2

IP Group #2 for MP-114

From the "Index" drop-down list, select "2"
In the "Description" field, type an arbitrary name for the IP Group (e.g. MP114)
From the "Proxy Set ID" drop-down list, select "2" (For this "IP Group" communicate with the "Proxy Set" of the MP-114)
In the "SIP Group Name" field, enter the IP Adress sent in the SIP Request From/To headers for this IP Group (MP-114's IP Adress)
Contact User = name that is sent in the SIP Request contact header for this IP Group (e.g. MP114)
From the "IP Profile ID" drop-down list, select "2" (the IP Profile is configured later)
Submit & Burn

IP Profiles for Voice Coders

For use transcoding it's necessary create two IP Profiles for define two types of coders used.

These profiles are later used in the "Inbound IP Routing" and "Outbound IP Routing" tables.

In the "Coder Group Settings" page (Configuration tab -> Protocol Configuration menu -> Coders And Profile Definitions submenu -> Coder Group Settings page):

Coder Group 1

Coder Group ID#1 for AlphaCom XE

From the "Coder Group ID" drop-down list, select "1"
In the "Coder Name" drop-down list, select "G.711U-law" (Coder used by AlphaCom)
Submit

Coder Group 2

Coder Group ID#2 for MP-114

From the "Coder Group ID" drop-down list, select "2"
In the "Coder Name" drop-down list, select "G.729" (Coder used by MP-114)
Submit & Burn

In the "IP Profile Settings" page (Configuration tab -> Protocol Configuration menu -> Coders And Profile Definitions submenu -> IP Profile Settings page):

Profile ID 1

Profile ID#1 for AlpahCom XE

From the "Profile ID" drop-down list, select "1"
From the "Coder Group" drop-down list, select "Coder Group 1"
Submit

Profile ID 2

Profile ID#2 for MP-114

From the "Profile ID" drop-down list, select "2"
In the "Coder Group" drop-down list, select "Coder Group 2"
Submit & Burn

IP Profiles for Voice Coders

For use transcoding it's necessary create two IP Profiles for define two types of coders used.

These profiles are later used in the "Inbound IP Routing" and "Outbound IP Routing" tables.

In the "Coder Group Settings" page (Configuration tab -> Protocol Configuration menu -> Coders And Profile Definitions submenu -> Coder Group Settings page):

Coder Group 1

Coder Group ID#1 for AlpahCom XE

From the "Coder Group ID" drop-down list, select "1"
In the "Coder Name" drop-down list, select "G.711U-law" (Coder used by AlphaCom)
Submit

Coder Group 2

Coder Group ID#2 for MP-114

From the "Coder Group ID" drop-down list, select "2"
In the "Coder Name" drop-down list, select "G.729" (Coder used by SIP Server)
Submit & Burn

In the "IP Profile Settings" page (Configuration tab -> Protocol Configuration menu -> Coders And Profile Definitions submenu -> IP Profile Settings page):

Profile ID 1

Profile ID#1 for AlpahCom XE

From the "Profile ID" drop-down list, select "1"
From the "Coder Group" drop-down list, select "Coder Group 1"
Submit

Profile ID 2

Profile ID#2 for MP-114

From the "Profile ID" drop-down list, select "2"
In the "Coder Group" drop-down list, select "Coder Group 2"
Submit & Burn

Inbound IP Routing

The "IP to Trunk Group Routing Table" it used for define the routing inbound IP-to-IP calls.

The table in which this is configured uses the IP Groups that you defined before.

In the "IP to Trunk Group Routing Table" page (Configuration tab -> Protocol Configuration menu -> Routing Tables submenu -> IP to Trunk Group Routing page):

Inbound IP Routing

Index#1 for AlpahCom XE7

Dest Phone Prefix : enter the asterisk (*) symbol to indicate all destinations
Source Phone Prefix : enter the asterisk (*) symbol to indicate all destinations
Source IP Adress : enter the IP adress of the AlphaCom
Trunk Group ID : enter "-1" to indicate that these calls are IP-to-IP calls
IP Profile ID : enter "1" to assign these calls to "ProfileID#1" to use "G.711U-law"
Source IP Groupe ID : enter "1" to assign these calls to the IP Group pertaining to the AlphaCom

Index#2 for MP-114

Dest Phone Prefix : enter the asterisk (*) symbol to indicate all destinations
Source Phone Prefix : enter the asterisk (*) symbol to indicate all destinations
Source IP Adress : enter the IP adress of the MP-114
Trunk Group ID : enter "-1" to indicate that these calls are IP-to-IP calls
IP Profile ID : enter "2" to assign these calls to "ProfileID#2" to use "G.729"
Source IP Groupe ID : enter "2" to assign these calls to the IP Group pertaining to the MP-114
Submit & Burn

Outbound IP Routing

The "Tel to IP Routing Table" it used for define the routing outbound IP-to-IP calls.

The table in which this is configured uses the IP Groups that you defined before.

In the "Tel to IP Routing" page (Configuration tab -> Protocol Configuration menu -> Routing Tables submenu -> Tel to IP Routing page):

Outbound IP Routing

Index#1 from AlpahCom XE7 to MP-114

Src.IPGroupID : select "1" to indicate received (inbound) calls identified as belonging to the IP Group configured for AlphaCom
Dest. Phone Prefix : enter the asterisk (*) symbol to indicate all destinations and callers respectively
Dest.IPGroupID : select "2" to indicate the destination IP Group to where these calls are sent, to the MP-114.
IP Profile ID : enter "2" to indicate the IP Profile configured for "G.729"

Index#2 from MP-114 to AlphaCom XE7

Src.IPGroupID : select "2" to indicate received (inbound) calls identified as belonging to the IP Group configured for MP-114
Dest. Phone Prefix : enter the asterisk (*) symbol to indicate all destinations and callers respectively
Dest.IPGroupID : select "1" to indicate the destination IP Group to where these calls are sent, to the AlphaCom.
IP Profile ID : enter "1" to indicate the IP Profile configured for "G.711µ-law"
Submit & Burn

Configuration of Mediant 600 with SIP Account as End Point

A license SIP to SIP Mediation and Routing Application (SW/IP2IP) is required. This section is additional to section = Mediant 600 Configuration =

Proxy Sets Table

These "Proxy Sets" are later assigned to "IP Groups" Note that the "Proxy Set" represents the actual destination to which the call is routed

In the "Proxy Sets Table" page (Configuration tab -> Protocol Configuration menu -> Proxies,Registration,IP Groups submenu -> Proxy Sets Table page):

Proxy Set ID1

Proxy Set ID#1 for AlpahCom XE

From the "Proxy Set ID" drop-down list, select "1"
In the "Proxy Address" column, enter the IP address of the AlphaCom
From the "Transport Type" drop-down list corresponding to the IP address entered above, select "UDP"
Submit

Proxy Set ID2

Proxy Set ID#2 for SIP Server

From the "Proxy Set ID" drop-down list, select "2"
In the "Proxy Address" column, enter the IP address of the SIP server
From the "Transport Type" drop-down list corresponding to the IP address entered above, select "UDP"
Set Enable Proxy Keep Alive to "Using Register"
Submit & Burn

IP Group Table

These "IP Groups" are later used by the device for routing calls

In the "IP Group Table" page (Configuration tab -> Protocol Configuration menu -> Proxies,Registration,IP Groups submenu -> IP Group Table page):

IP Group 1

IP Group #1 for AlpahCom XE7

From the "Index" drop-down list, select "1"
In the "Description" field, type an arbitrary name for the IP Group (e.g. AlphaCom)
From the "Proxy Set ID" drop-down list, select "1" (For this "IP Group" communicate with the "Proxy Set" of the AlphaCom)
From the "IP Profile ID" drop-down list, select "1" (the IP Profile is configured later)
Submit

IP Group 2

IP Group #2 for SIP-Server

From the "Index" drop-down list, select "2"
In the "Description" field, type an arbitrary name for the IP Group (e.g. 51215382)
From the "Proxy Set ID" drop-down list, select "2" (For this "IP Group" communicate with the "Proxy Set" of the SIPServer)
If more then one Account, repeat the same above with IP Group nr not in use(e.g. IP Group nr 3)
From the "IP Profile ID" drop-down list, select "2". Do the same for all other IP Group associated with SIP Servers IP Groups(the IP Profile is configured later)
Submit & Burn

IP Profiles for Voice Coders

For use transcoding it's necessary create two IP Profiles for define two types of coders used.

These profiles are later used in the "Inbound IP Routing" and "Outbound IP Routing" tables.

In the "Coder Group Settings" page (Configuration tab -> Protocol Configuration menu -> Coders And Profile Definitions submenu -> Coder Group Settings page):

Coder Group 1

Coder Group ID#1 for AlpahCom XE7

From the "Coder Group ID" drop-down list, select "1"
In the "Coder Name" drop-down list, select "G.711U-law" (Coder used by AlphaCom)
Submit

Coder Group 2

Coder Group ID#2 for SIP Server

From the "Coder Group ID" drop-down list, select "2"
In the "Coder Name" drop-down list, select "G.729" (Coder used by SIP Server)
Note: If SIP Provider supports another Codec, please choose from the drop down list.
Submit & Burn

In the "IP Profile Settings" page (Configuration tab -> Protocol Configuration menu -> Coders And Profile Definitions submenu -> IP Profile Settings page):

Profile ID 1

Profile ID#1 for AlpahCom XE7

Enter the Profile name "AlphaCom"
From the "Profile ID" drop-down list, select "1"
From the "Coder Group" drop-down list, select "Coder Group 1"
Submit

Profile ID 2

Profile ID#2 for SIP Server

Enter the Profile name "SIP Server"
From the "Profile ID" drop-down list, select "2"
In the "Coder Group" drop-down list, select "Coder Group 2"
Submit & Burn

Account Table

These "Account Table" should be assigned to "IP Groups" for each account to control which account to call out with.

Note that the "IP Groups" is made for each Account done in earlier step.

In the "Proxy Sets Table" page (Configuration tab -> Control Network menu -> SIP Definitions submenu -> Account Table page):

Account Tables

Account Table for SIP Server

Start line 1 in Add field and Press "Add"
Set Served IP Group to 1
Set Served IP Trunk Group to -1
Set Serving IP Group same as the Serving IP group associated in IP Group used by this account.
Set Username and Password due to information from SIP Provider
From the "Register" drop-down list, select "YES"
Set "Contact User" to SIP ID
From the "Application Type" drop-down list, select "GW\IP2IP"
Submit

Inbound IP Routing

The "IP to Trunk Group Routing Table" it used for define the routing inbound IP-to-IP calls.

The table in which this is configured uses the IP Groups that you defined before.

In the "IP to Trunk Group Routing Table" page (Configuration tab -> Protocol Configuration menu -> Routing Tables submenu -> IP to Trunk Group Routing page):

Inbound IP Routing

Index#1 for AlpahCom XE7

Dest Phone Prefix : enter the asterisk (*) symbol to indicate all destinations
Source Phone Prefix : enter the asterisk (*) symbol to indicate all destinations
Source IP Adress : enter the IP adress of the AlphaCom
Trunk Group ID : enter "-1" to indicate that these calls are IP-to-IP calls
IP Profile ID : enter "1" to assign these calls to "ProfileID#1" to use "G.711U-law"
Source IP Groupe ID : enter "1" to assign these calls to the IP Group pertaining to the AlphaCom

Index#2 for SIP Server

Dest Phone Prefix : enter the asterisk (*) symbol to indicate all destinations
Source Phone Prefix : enter the asterisk (*) symbol to indicate all destinations
Source IP Adress : enter * to receive calls from all URL/IP adresses of the SIP server
Trunk Group ID : enter "-1" to indicate that these calls are IP-to-IP calls
IP Profile ID : enter "2" to assign these calls to "ProfileID#2" to use "G.729"
Source IP Groupe ID : enter "2" to assign these calls to the IP Group pertaining to the SIP Server
Note: Enter Sorce IP Group nr of the every account you register in Accout Table in next step
Submit & Burn

Outbound IP Routing

The "Tel to IP Routing Table" it used for define the routing outbound IP-to-IP calls.

The table in which this is configured uses the IP Groups that you defined before.

In the "Tel to IP Routing" page (Configuration tab -> Protocol Configuration menu -> Routing Tables submenu -> Tel to IP Routing page):

Outbound IP Routing

Index#1 from AlpahCom XE7 to SIPServer

Src.IPGroupID : select "1" to indicate received (inbound) calls identified as belonging to the IP Group configured for AlphaCom
Dest. Phone Prefix : enter the asterisk (*) symbol to indicate all destinations and callers respectively
Dest.IPGroupID : select "2" to indicate the destination IP Group to where these calls are sent, to the SIP-Server
IP Profile ID : enter "2" to indicate the IP Profile configured for "G.729"
Note: Enter a new line with "Source Phone Prefix" set to Extension and "Dest. IP Group ID" to associated SIP account. This to control which SIP Account the each extension is using.

Index#2 from SIP Server to AlphaCom XE7

Src.IPGroupID : select "2" to indicate received (inbound) calls identified as belonging to the IP Group configured for MP-114
Dest. Phone Prefix : enter the asterisk (*) symbol to indicate all destinations and callers respectively
Dest.IPGroupID : select "1" to indicate the destination IP Group to where these calls are sent, to the AlphaCom.
IP Profile ID : enter "1" to indicate the IP Profile configured for "G.711µ-law"
Submit & Burn

Manipulation Table

This step will change the local SIP ID/Dir No to number associated to SIP accounts.

In the "Source Number Tel->IP" page (VoIP tab -> Control Network menu -> GW and IP to IP submenu -> Manipulation page):

Manipulation Tel->IP Calls

Manipulation Table for Outgoing Calls

This step is necessary to route inncoming call to right Extension on AlphaCom side.

In the "Dest Number IP->Tel" page (VoIP tab -> Control Network menu -> GW and IP to IP submenu -> Manipulation page):

Manipulation IP-> Tel Calls

Manipulation Table for route the inncoming call

Submit

AudioCodes MP-114/118 Configuration

All text and pictures refer to version 5.80

For configuration of the MP114/118 please see Configuration guide for AudioCodes MP114/118, v5.4 and higher.

The following highlighted points deviate from the standard MP114/118 configuration and are special for the SIP2SIP transcoding with AlphaCom using AudioCodes Mediant 600:

SIP Parameters

In the Proxy & Registration page (Configuration tab -> Protocol Configuration menu -> Protocol Definition submenu -> Proxy & Registration page item) set the ‘Use Default Proxy’ field to ‘Yes’.

Proxy Name must be blank
Gateway Name must be blank
Click the Proxy Set Table button. In the ‘Proxy Address’ field enter the IP address of the Mediant 600.
Set 'Transport Type' to 'UDP'.

Press Submit to save changes

Audio Codec

Select the voice coder in 'Coders Table' page (Configuration tab -> Protocol Configuration menu -> Protocol Definition submenu -> Coders page item).

From the drop-down list select G.729

Press Submit to save changes

Cisco Call Manager Configuration

All text and pictures refer to version 6.1.2

For configuration of the Cisco Call Manager please see Cisco Call Manager 6 configuration guide.

The following highlighted points deviate from the standard CUCM configuration and are special for the SIP2SIP transcoding with AlphaCom using AudioCodes Mediant 600:

Configure a Region

Region Configuration

System -> Region -> Add New

Name: Zenitel
Press Save
Under Modify Relationships to other Regions select Zenitel.
Select Audio Codec to G.729
Press Save
Press Reset/Restart

Configure a SIP Trunk

Trunk Configuration

Trunk Configuration, continued

Device -> Trunk -> Add New

Trunk Type: SIP Trunk
Device Protocol: SIP
Press Next
Device Name: AlphaCom
Description: AlphaCom
Device Pool: Zenitel
Media Resource Group List: AlphaCom_MRGL
Enable: 'Media Termination Point Required'
Calling Search Space: DefaultUser
Destination Adress: The IP adress of the Mediant 600
SIP Trunk Security Profile: AlphaCom
SIP Profile: Standard SIP Profile
Press Save
Press Reset/Restart

Mobile VoIP GSM Gateway MV-370

All text and pictures refer to version 6.693.t

For configuration of the MV-370 please see Configuration guide for Mobile VoIP.

The following highlighted points deviate from the standard MV-370 configuration and are special for the SIP2SIP transcoding with AlphaCom using AudioCodes Mediant 600:

SIP settings

SIP Settings

In the menu SIP Settings -> Service Domain, enter information for "Realm 1":

Active = ON
User Name = Any text, used for Caller ID. This text will be shown in the display on incoming calls from the GSM network, together with the telephone number
Proxy Server = IP address of the Mediant 600

Status will show Not Registered.

Enable DTMF signalling by SIP INFO method:

SIP Settings > DTMF Setting: Enable Send DTMF SIP Info

Codec settings

Codec Settings

In the menu SIP Settings -> Codec Settings, set codec priority:

Codec Priority 1: = G.729

Leave the rest as is.

Difference between revisions of "SIP2SIP Transcoding using Mediant 600"

From Zenitel Wiki

Latest revision as of 11:39, 15 August 2022

Contents

AlphaCom Configuration

Mediant 600 Configuration

Restore to factory default settings

Access to the embedded web server

IP Configuration

Add Software Upgrade Key

Enable IP-to-IP Capabilities

Number of Media Channels

Proxy Sets Table

IP Group Table

IP Profiles for Voice Coders

IP Profiles for Voice Coders

Inbound IP Routing

Outbound IP Routing

Configuration of Mediant 600 with SIP Account as End Point

Proxy Sets Table

IP Group Table

IP Profiles for Voice Coders

Account Table

Inbound IP Routing

Outbound IP Routing

Manipulation Table

AudioCodes MP-114/118 Configuration

SIP Parameters

Audio Codec

Cisco Call Manager Configuration

Configure a Region

Configure a SIP Trunk

Mobile VoIP GSM Gateway MV-370

SIP settings

Codec settings

@@ Line 1: / Line 1: @@
+{{A}}
 The Mediant 600 has the capability to transcode a SIP call from e.g. G711µ-law to G729. Here are some examples using the Mediant 600 to transcode G711µ-law to G729.
 The examples shown are between:
-:* AlphaCom XE7 and Cisco Call Manager
+:* AlphaCom XE and Cisco Call Manager
-:* AlphaCom XE7 and AudioCodes MP-114/118
+:* AlphaCom XE and AudioCodes MP-114/118
-:* AlphaCom XE7 and Mobile VoIP GSM Gateway MV-370
+:* AlphaCom XE and Mobile VoIP GSM Gateway MV-370
 [[Image:SIP2SIP-M600.PNG|thumb|650px|Configuration example]]
@@ Line 10: / Line 11: @@
 = AlphaCom Configuration =
-''All text and pictures refer to AMC version 11.1.3.3''
-<br/>
-<br/>
-== AlphaWeb Configuration ==
-=== Assign IP address to the AlphaCom XE Ethernet port(s) ===
-Log on to AlphaWeb and enter a valid IP address on the Ethernet port.
-In the example below, Ethernet port 1 is used.
-Consult your network administrator to obtain the IP address.
-[[image:AlphaWeb Int3.PNG|thumb|left|500px|]]
-<br style="clear:both;" />
-=== Insert SIP Trunk licenses ===
-The AlphaCom requires only 1 x SIP Trunk License for this configuration. <br/>
-Log on to AlphaWeb and install the SIP Trunk license.
-[[image:AXE7-InsertLicense.PNG|thumb|left|500px|]]
-<br style="clear:both;" />
-=== Firewall (filter) settings ===
-Enable the SIP protocol on the desired Ethernet port
-(default enabled for Ethernet port1).
-[[image:AXE7-Filters.PNG|thumb|left|500px|]]
-<br style="clear:both;" />
-== AlphaPro Configuration ==
-=== Create a SIP Trunk Node ===
-From the AlphaPro main menu, use the ‘+’ button next to the ‘Select Exchange’ dropdown list to create a new exchange. The exchange type must be set to ‘SIP Node’.
-Set the parameters as shown in the image:
-[[image:Configuration guide for AudioCodes MP114 118 - Create a SIP Trunk Node.PNG|thumb|left|500px|]]
-<br style="clear:both;" />
-The SIP Trunk IP address must be identical to the IP address of the SIP Gateway (i.e. Mediant 600).
-'''Note:''' If the AlphaCom is configured with a SIP Registar node in addition to the SIP Trunk node, the SIP Registar node must have a lower node number than the SIP Trunk node.
-<br style="clear:both;" />
-=== Create AlphaCom/SIP Audio links ===
-''This paragraph is only relevant for AMC software 10.04 or earlier.''
-From AMC 10.05 the audio links are assigned dynamically whenever needed, and there is no need to specify the links in AlphaPro. Proceed to [http://10.5.2.54/wiki/index.php/Configuration_guide_for_AudioCodes_MP114/118#Define_the_AlphaCom_.2F_SIP_routing Define the AlphaCom / SIP routing].
-However, if you want to reserve VoIP channels for the SIP Gateway, you can do so by following the description below.
-In '''Exchange & System > NetAudio''' use the ''Insert'' button to create one or several audio (VoIP) links between the AlphaCom and the SIP Gateway. The physical number specifies the VoIP channel and must be in the range 605 – 634 (start with 605). Normally the number of audio links will be equal to the number of phone lines connected to the SIP Gateway.
-[[image:Configuration guide for AudioCodes MP114 118 - Create AlphaCom SIP Audio links.PNG|thumb|left|500px|]]
-<br style="clear:both;" />
-=== Define the AlphaCom / SIP routing ===
-In '''Exchange & System > Net Routing''' use the ''Insert'' button to create a
-route between the AlphaCom and SIP Gateway. Set '''Preferred codec'''
-to ''G711u'' and '''RTP Packet Size''' to ''20 ms''.
-[[image:Configuration guide for AudioCodes MP114 118 - Define the AlphaCom SIP routing.PNG|thumb|left|500px|]]
-<br style="clear:both;" />
-=== Prefix and Global numbers ===
-The telephone line can be accessed in different ways:
-* Prefix number: Dial Prefix + Phone number. “Phone number” will be called
-* Integrated Prefix number: Dial Prefix + Phone number. The prefix will be included as a part of the called telephone number.
-* Global number: Dial the phone number without using prefix
-==== Prefix number ====
-The directory number must be programmed in the AlphaCom directory table with feature 81 and Node = SIP Trunk node number (100 in this example). In the “Parameter 2” field (“Collect N more digits (SIP)” in earlier AlphaPro versions) you must enter the maximum number of digits in a phone number.
-When the prefix is dialed, the AlphaCom will wait for further digits. When the number of digits specified in the “Parameter 2” field (Collect N more digits (SIP in earlier versions of AlphaPro) are collected, a call setup message is sent to the SIP gateway. If fewer digits are entered, the AlphaCom will time out after 4 seconds, and the call setup message will be sent. You can also terminate the digit collection by pressing the M-key. The call setup message will then be sent immediately.
+How to set up a SIP Trunk in the AlphaCom is described here: [[SIP trunk node - configuration]]
-In the example below the directory number 0 is used as a prefix.
-[[image:Example of prefix number.PNG|thumb|left|500px|Example of prefix number]]
-<br style="clear:both;" />
-Dialing examples:
-: 0 + 12345678: Telephone number 12345678 will be called
-: 0 + 1234: After a 4 second timeout, telephone number 1234 will be called
-: 0 + 1234 + M: Telephone number 1234 will be called
-==== Integrated Prefix number ====
-The directory number must be programmed in the AlphaCom directory table with feature 83 and Node = SIP Trunk node number (100 in this example). In the “Parameter 2” field (“Collect N more digits (SIP)” in earlier AlphaPro versions) you must enter the maximum number of digits in a phone number.
-When the prefix is dialed, the AlphaCom will wait for further digits. When the number of digits specified in the “Parameter 2” field (“Collect N more digits (SIP)” in earlier AlphaPro versions) are collected, a call setup message is sent to the SIP gateway. If fewer digits are entered, the AlphaCom will time out after 4 seconds, and the call setup message will be sent. You can also terminate the digit collection by pressing the M-key. The call setup message will then be sent immediately.
-In the example below the directory number 57 is used as a prefix.
-[[image:Example of integrated prefix number.PNG|thumb|left|500px|Example of integrated prefix number]]
-<br style="clear:both;" />
-Dialing examples:
-: 57 + 12345678: Telephone number 5712345678 will be called
-: 57 + 1234: After a 4 second timeout, telephone number 571234 will be called
-: 57 + 1234 + M: Telephone number 571234 will be called
-==== Global number ====
-The directory number must be programmed in the AlphaCom directory table with feature 83 and Node = SIP Trunk node number (100 in this example). The “Parameter 2” field (in earlier AlphaPro version “Collect N more digits (SIP)”) must be left blank.
-When the global number is dialed, the AlphaCom will immediately send a call setup message to the SIP gateway.
-In the example below directory number 12345678 is defined as a global number. When dialing this number a call setup message is sent to the SIP gateway, instructing it to call this phone number.
-[[image:Example of global number.PNG|thumb|left|500px|Example of global number]]
-<br style="clear:both;" />
-=== Update the exchange ===
-Log on to the exchange and update the exchange by pressing the
-SendAll button.
 = Mediant 600 Configuration =
@@ Line 126: / Line 20: @@
 == Restore to factory default settings ==
-[[Image:M1K Ext.Comm. ResetButton.png|thumb|350px|Reset Button]]
+[[Image:M1K Ext.Comm. ResetButton.png|left|thumb|500px|Reset Button]]
+<br style="clear:both;" />
 :*With a paper clip, press and hold down the Reset button (located on the CPU Module) for at least 12 seconds (no more than 25 seconds)<br>
 :*The device restores to factory default settings<br>
+== Access to the embedded web server ==
+[[Image:M600-Home.PNG|left|thumb|500px|Home Page]]
 <br style="clear:both;" />
-== Access to the embedded web server ==
-[[Image:M600-Home.PNG|thumb|350px|Home Page]]
 :The default Network parameter of the Mediant 600:
@@ Line 155: / Line 49: @@
 '''''<u>Note:</u>''' For the rest of configuration used the tree menu in '''Full''' mode''
+== IP Configuration ==
+[[Image:AudioCodes Mediant 1000 Configure Network Parameters.jpg|left|thumb|500px|Initial configuration]]
 <br style="clear:both;" />
-== IP Configuration ==
 RETURN TO THIS
-[[Image:AudioCodes Mediant 1000 Configure Network Parameters.jpg|thumb|150px|Initial configuration]]
+[[Image:M1K Ext.Comm. IPConfig.png|left|thumb|500px|IP Settings]]
-[[Image:M1K Ext.Comm. IPConfig.png|thumb|350px|IP Settings]]
+<br style="clear:both;" />
 :In the "IP Settings" page ('''Configuration''' tab -> '''Network Settings''' menu -> '''IP Settings''' page) enter :
@@ Line 168: / Line 62: @@
 ::*Default Gateway
 ::* Click "Submit" to apply the changes
-<br>
 :The IP address is immediately changed when pressing Submit, but it is not permanently stored<br>
 :Without resetting or powering off the device, you need to log on to the Gateway using its new IP address in order to Burn the new IP address to flash:
@@ Line 176: / Line 70: @@
 ::* Click "Burn" to permanently apply the changes
+== Add Software Upgrade Key ==
+The license for SIP IP2IP must be uploaded as a Software Upgrade Key.
+[[Image:M600-InsertLicense.JPG|left|thumb|500px|Software Upgrade Key]]
 <br style="clear:both;" />
-== Add Software Upgrade Key ==
-[[Image:M600-InsertLicense.JPG|thumb|350px|Software Upgrade Key]]
-The license for SIP IP2IP must be uploaded as a Software Upgrade Key.
 :In the "Software Upgrade Key Status" page ('''Management''' tab -> '''Software Update''' menu -> '''Software Upgrade Key''' page): <br/>
 ::*Enter the license key in the "Add a Software Upgrade Key" field
@@ Line 187: / Line 81: @@
 ::*Reset the device (Device Action -> Reset -> Reset)
+== Enable IP-to-IP Capabilities ==
+[[Image:M600-EnableIP2IP.PNG|left|thumb|500px|Applications Enabling]]
 <br style="clear:both;" />
-== Enable IP-to-IP Capabilities ==
-[[Image:M600-EnableIP2IP.PNG|thumb|350px|Applications Enabling]]
 :In the "Applications Enabling" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Applications Enabling''' page):<br>
@@ Line 198: / Line 90: @@
 ::*Wait the next step for Reset the device
+== Number of Media Channels ==
+[[Image:M600-SetNumberOfMediaChannels.PNG|left|thumb|500px|IP Media Settings]]
 <br style="clear:both;" />
-== Number of Media Channels ==
-[[Image:M600-SetNumberOfMediaChannels.PNG|thumb|350px|IP Media Settings]]
 :In the "IP Media Settings" page ('''Configuration''' tab -> '''Media Settings''' menu -> '''IP Media Settings''' page):<br>
@@ Line 207: / Line 98: @@
 ::*Submit & Burn
 ::*Reset the device (Device Action -> Reset -> Reset)
-<br style="clear:both;" />
 == Proxy Sets Table ==
-[[Image:M600-SetProxy1.PNG|thumb|350px|Proxy Set ID1]]
-[[Image:M600-SetProxy2.PNG|thumb|350px|Proxy Set ID2]]
 These "Proxy Sets" are later assigned to "IP Groups"
 Note that the "Proxy Set" represents the actual destination to which the call is routed
-<br>
-<br>
 :In the "Proxy Sets Table" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Proxies,Registration,IP Groups''' submenu -> '''Proxy Sets Table''' page):<br>
+[[Image:M600-SetProxy1.PNG|left|thumb|500px|Proxy Set ID1]]
+<br style="clear:both;" />
-:*Proxy Set ID#1 for AlpahCom XE7
+:*Proxy Set ID#1 for AlpahCom XE
 ::*From the "Proxy Set ID" drop-down list, select "1"
 ::*In the "Proxy Address" column, enter the IP address of the AlphaCom
 ::*From the "Transport Type" drop-down list corresponding to the IP address entered above, select "UDP"
 ::*Submit
+----
+[[Image:M600-SetProxy2.PNG|left|thumb|500px|Proxy Set ID2]]
+<br style="clear:both;" />
+:*Proxy Set ID#2 for MP-114
+::*From the "Proxy Set ID" drop-down list, select "2"
+::*In the "Proxy Address" column, enter the IP address of the MP-114
+::*From the "Transport Type" drop-down list corresponding to the IP address entered above, select "UDP"
+::*Submit & Burn
+<br style="clear:both;" />
 == IP Group Table ==
+These "IP Groups" are later used by the device for routing calls
-These "IP Groups" are later used by the device for routing calls
-<br>
-<br>
 :In the "IP Group Table" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Proxies,Registration,IP Groups''' submenu -> '''IP Group Table''' page):<br>
-[[Image:M600-SetIPGroup1.PNG|thumb|350px|IP Group 1]]
+[[Image:M600-SetIPGroup1.PNG|left|thumb|500px|IP Group 1]]
-:*IP Group #1 for AlpahCom XE7
+<br style="clear:both;" />
+:*IP Group #1 for AlpahCom XE
 ::*From the "Index" drop-down list, select "1"
 ::*In the "Description" field, type an arbitrary name for the IP Group (e.g. AlphaCom)
 ::*From the "Proxy Set ID" drop-down list, select "1" (For this "IP Group" communicate with the "Proxy Set" of the AlphaCom)
 ::*In the "SIP Group Name" field, enter the IP Adress sent in the SIP Request From/To headers for this IP Group (AlphaCom's IP Adress)
-::*Contact User = name that is sent in the SIP Request contact header for this IP Group (e.g. AXE7)
+::*Contact User = name that is sent in the SIP Request contact header for this IP Group (e.g. AXE)
 ::*From the "IP Profile ID" drop-down list, select "1" (the IP Profile is configured later)
 ::*Submit
+----
+[[Image:M600-SetIPGroup2.PNG|left|thumb|500px|IP Group 2]]
 <br style="clear:both;" />
-[[Image:M600-SetIPGroup2.PNG|thumb|350px|IP Group 2]]
 :*IP Group #2 for MP-114
 ::*From the "Index" drop-down list, select "2"
@@ Line 258: / Line 153: @@
 <br style="clear:both;" />
+== IP Profiles for Voice Coders ==
+For use transcoding it's necessary create two IP Profiles for define two types of coders used.
-:*Proxy Set ID#2 for MP-114
+These profiles are later used in the "Inbound IP Routing" and "Outbound IP Routing" tables.
-::*From the "Proxy Set ID" drop-down list, select "2"
-::*In the "Proxy Address" column, enter the IP address of the MP-114
-::*From the "Transport Type" drop-down list corresponding to the IP address entered above, select "UDP"
-::*Submit & Burn
-<br style="clear:both;" />
-== IP Profiles for Voice Coders ==
-For use transcoding it's necessary create two IP Profiles for define two types of coders used.<br>
-These profiles are later used in the "Inbound IP Routing" and "Outbound IP Routing" tables.
-<br>
-<br>
 :In the "Coder Group Settings" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Coders And Profile Definitions''' submenu -> '''Coder Group Settings''' page):<br>
-[[Image:M600-CoderGroup1.PNG|thumb|350px|Coder Group 1]]
+[[Image:M600-CoderGroup1.PNG|left|thumb|500px|Coder Group 1]]
-:*Coder Group ID#1 for AlpahCom XE7
+<br style="clear:both;" />
+:*Coder Group ID#1 for AlphaCom XE
 ::*From the "Coder Group ID" drop-down list, select "1"
 ::*In the "Coder Name" drop-down list, select "G.711U-law" (Coder used by AlphaCom)
 ::*Submit
 <br style="clear:both;" />
+----
-[[Image:M600-CoderGroup2.PNG|thumb|350px|Coder Group 2]]
+[[Image:M600-CoderGroup2.PNG|left|thumb|500px|Coder Group 2]]
+<br style="clear:both;" />
 :*Coder Group ID#2 for MP-114
 ::*From the "Coder Group ID" drop-down list, select "2"
@@ Line 289: / Line 177: @@
 <br style="clear:both;" />
+----
 :In the "IP Profile Settings" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Coders And Profile Definitions''' submenu -> '''IP Profile Settings''' page):<br>
-[[Image:M600-IPProfile1.PNG|thumb|350px|Profile ID 1]]
+[[Image:M600-IPProfile1.PNG|left|thumb|500px|Profile ID 1]]
-:*Profile ID#1 for AlpahCom XE7
+<br style="clear:both;" />
+:*Profile ID#1 for AlpahCom XE
 ::*From the "Profile ID" drop-down list, select "1"
 ::*From the "Coder Group" drop-down list, select "Coder Group 1"
@@ Line 299: / Line 188: @@
 <br style="clear:both;" />
+----
-[[Image:M600-IPProfile2.PNG|thumb|350px|Profile ID 2]]
+[[Image:M600-IPProfile2.PNG|left|thumb|500px|Profile ID 2]]
+<br style="clear:both;" />
 :*Profile ID#2 for MP-114
 ::*From the "Profile ID" drop-down list, select "2"
@@ Line 309: / Line 199: @@
 == IP Profiles for Voice Coders ==
+For use transcoding it's necessary create two IP Profiles for define two types of coders used.
-For use transcoding it's necessary create two IP Profiles for define two types of coders used.<br>
 These profiles are later used in the "Inbound IP Routing" and "Outbound IP Routing" tables.
-<br>
-<br>
 :In the "Coder Group Settings" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Coders And Profile Definitions''' submenu -> '''Coder Group Settings''' page):<br>
-[[Image:CoderGroupAlphaCom.jpg|thumb|350px|Coder Group 1]]
+[[Image:CoderGroupAlphaCom.jpg|left|thumb|500px|Coder Group 1]]
-:*Coder Group ID#1 for AlpahCom XE7
+<br style="clear:both;" />
+:*Coder Group ID#1 for AlpahCom XE
 ::*From the "Coder Group ID" drop-down list, select "1"
 ::*In the "Coder Name" drop-down list, select "G.711U-law" (Coder used by AlphaCom)
 ::*Submit
 <br style="clear:both;" />
+----
-[[Image:CoderGroupSIPServer.jpg|thumb|350px|Coder Group 2]]
+[[Image:CoderGroupSIPServer.jpg|left|thumb|500px|Coder Group 2]]
+<br style="clear:both;" />
 :*Coder Group ID#2 for MP-114
 ::*From the "Coder Group ID" drop-down list, select "2"
@@ Line 330: / Line 222: @@
 <br style="clear:both;" />
+----
 :In the "IP Profile Settings" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Coders And Profile Definitions''' submenu -> '''IP Profile Settings''' page):<br>
-[[Image:M600-IPProfile1.PNG|thumb|350px|Profile ID 1]]
+[[Image:M600-IPProfile1.PNG|left|thumb|500px|Profile ID 1]]
-:*Profile ID#1 for AlpahCom XE7
+<br style="clear:both;" />
+:*Profile ID#1 for AlpahCom XE
 ::*From the "Profile ID" drop-down list, select "1"
 ::*From the "Coder Group" drop-down list, select "Coder Group 1"
@@ Line 340: / Line 233: @@
 <br style="clear:both;" />
+----
-[[Image:M600-IPProfile2.PNG|thumb|350px|Profile ID 2]]
+[[Image:M600-IPProfile2.PNG|left|thumb|500px|Profile ID 2]]
+<br style="clear:both;" />
 :*Profile ID#2 for MP-114
 ::*From the "Profile ID" drop-down list, select "2"
@@ Line 350: / Line 244: @@
 == Inbound IP Routing ==
+The "IP to Trunk Group Routing Table" it used for define the routing inbound IP-to-IP calls.
-The "IP to Trunk Group Routing Table" it used for define the routing inbound IP-to-IP calls.<br>
 The table in which this is configured uses the IP Groups that you defined before.
-<br>
-<br>
 :In the "IP to Trunk Group Routing Table" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Routing Tables''' submenu -> '''IP to Trunk Group Routing''' page):<br>
-[[Image:M600-RoutingIPTrunkGroup.PNG|thumb|350px|Inbound IP Routing]]
+[[Image:M600-RoutingIPTrunkGroup.PNG|left|thumb|500px|Inbound IP Routing]]
+<br style="clear:both;" />
 :*Index#1 for AlpahCom XE7
@@ Line 379: / Line 274: @@
 == Outbound IP Routing ==
+The "Tel to IP Routing Table" it used for define the routing outbound IP-to-IP calls.
-The "Tel to IP Routing Table" it used for define the routing outbound IP-to-IP calls.<br>
 The table in which this is configured uses the IP Groups that you defined before.
-<br>
-<br>
 :In the "Tel to IP Routing" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Routing Tables''' submenu -> '''Tel to IP Routing''' page):<br>
-[[Image:M600-RoutingTelToIP.PNG|thumb|350px|Outbound IP Routing]]
+[[Image:M600-RoutingTelToIP.PNG|left|thumb|500px|Outbound IP Routing]]
+<br style="clear:both;" />
 :*Index#1 from AlpahCom XE7 to MP-114
@@ Line 410: / Line 306: @@
 == Proxy Sets Table ==
-[[Image:ProxySet1.JPG|thumb|350px|Proxy Set ID1]]
-[[Image:ProxySet2.JPG|thumb|350px|Proxy Set ID2]]
 These "Proxy Sets" are later assigned to "IP Groups"
 Note that the "Proxy Set" represents the actual destination to which the call is routed
-<br>
-<br>
-:In the "Proxy Sets Table" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Proxies,Registration,IP Groups''' submenu -> '''Proxy Sets Table''' page):<br>
-:*Proxy Set ID#1 for AlpahCom XE7
+:In the "Proxy Sets Table" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Proxies,Registration,IP Groups''' submenu -> '''Proxy Sets Table''' page):
+[[Image:ProxySet1.JPG|left|thumb|500px|Proxy Set ID1]]
+<br style="clear:both;" />
+:*Proxy Set ID#1 for AlpahCom XE
 ::*From the "Proxy Set ID" drop-down list, select "1"
 ::*In the "Proxy Address" column, enter the IP address of the AlphaCom
 ::*From the "Transport Type" drop-down list corresponding to the IP address entered above, select "UDP"
 ::*Submit
+----
+[[Image:ProxySet2.JPG|left|thumb|500px|Proxy Set ID2]]
+<br style="clear:both;" />
 :*Proxy Set ID#2 for SIP Server
 ::*From the "Proxy Set ID" drop-down list, select "2"
@@ Line 436: / Line 330: @@
 == IP Group Table ==
+These "IP Groups" are later used by the device for routing calls
-These "IP Groups" are later used by the device for routing calls
+:In the "IP Group Table" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Proxies,Registration,IP Groups''' submenu -> '''IP Group Table''' page):
-<br>
-<br>
-:In the "IP Group Table" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Proxies,Registration,IP Groups''' submenu -> '''IP Group Table''' page):<br>
-[[Image:IPGrouptable-AlphaCom.jpg|thumb|350px|IP Group 1]]
+[[Image:IPGrouptable-AlphaCom.jpg|left|thumb|500px|IP Group 1]]
+<br style="clear:both;" />
 :*IP Group #1 for AlpahCom XE7
 ::*From the "Index" drop-down list, select "1"
@@ Line 451: / Line 345: @@
 <br style="clear:both;" />
+----
-[[Image:IPGrouptable-SIPserverAccount.jpg|thumb|350px|IP Group 2]]
+[[Image:IPGrouptable-SIPserverAccount.jpg|left|thumb|500px|IP Group 2]]
+<br style="clear:both;" />
 :*IP Group #2 for SIP-Server
 ::*From the "Index" drop-down list, select "2"
@@ Line 464: / Line 359: @@
 == IP Profiles for Voice Coders ==
+For use transcoding it's necessary create two IP Profiles for define two types of coders used.
-For use transcoding it's necessary create two IP Profiles for define two types of coders used.<br>
 These profiles are later used in the "Inbound IP Routing" and "Outbound IP Routing" tables.
-<br>
-<br>
-:In the "Coder Group Settings" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Coders And Profile Definitions''' submenu -> '''Coder Group Settings''' page):<br>
-[[Image:CoderGroupAlphaCom.jpg|thumb|350px|Coder Group 1]]
+:In the "Coder Group Settings" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Coders And Profile Definitions''' submenu -> '''Coder Group Settings''' page):
+[[Image:CoderGroupAlphaCom.jpg|left|thumb|500px|Coder Group 1]]
+<br style="clear:both;" />
 :*Coder Group ID#1 for AlpahCom XE7
 ::*From the "Coder Group ID" drop-down list, select "1"
@@ Line 477: / Line 373: @@
 ::*Submit
 <br style="clear:both;" />
+----
-[[Image:CoderGroupSIPServer.jpg|thumb|350px|Coder Group 2]]
+[[Image:CoderGroupSIPServer.jpg|left|thumb|500px|Coder Group 2]]
+<br style="clear:both;" />
 :*Coder Group ID#2 for SIP Server
 ::*From the "Coder Group ID" drop-down list, select "2"
@@ Line 484: / Line 381: @@
 ::*Note: If SIP Provider supports another Codec, please choose from the drop down list.
 ::*Submit & Burn
 <br style="clear:both;" />
+----
 :In the "IP Profile Settings" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Coders And Profile Definitions''' submenu -> '''IP Profile Settings''' page):<br>
-[[Image:IPProfileAlphaCom.jpg|thumb|350px|Profile ID 1]]
+[[Image:IPProfileAlphaCom.jpg|left|thumb|500px|Profile ID 1]]
+<br style="clear:both;" />
 :*Profile ID#1 for AlpahCom XE7
 ::*Enter the Profile name "AlphaCom"
@@ Line 495: / Line 392: @@
 ::*From the "Coder Group" drop-down list, select "Coder Group 1"
 ::*Submit
 <br style="clear:both;" />
+----
-[[Image:IPProfileSIPServer.jpg|thumb|350px|Profile ID 2]]
+[[Image:IPProfileSIPServer.jpg|left|thumb|500px|Profile ID 2]]
+<br style="clear:both;" />
 :*Profile ID#2 for SIP Server
 ::*Enter the Profile name "SIP Server"
@@ Line 504: / Line 401: @@
 ::*In the "Coder Group" drop-down list, select "Coder Group 2"
 ::*Submit & Burn
 <br style="clear:both;" />
 == Account Table ==
-[[Image:AccountTable.jpg|thumb|350px|Account Tables]]
+These "Account Table" should be assigned to "IP Groups" for each account to control which account to call out with.
-These "Account Table" should be assigned to "IP Groups" for each account to control which account to call out with.
 Note that the "IP Groups" is made for each Account done in earlier step.
-<br>
-<br>
-:In the "Proxy Sets Table" page ('''Configuration''' tab -> '''Control Network''' menu -> '''SIP Definitions''' submenu -> '''Account Table''' page):<br>
+:In the "Proxy Sets Table" page ('''Configuration''' tab -> '''Control Network''' menu -> '''SIP Definitions''' submenu -> '''Account Table''' page):
+[[Image:AccountTable.jpg|left|thumb|500px|Account Tables]]
+<br style="clear:both;" />
 :*Account Table for SIP Server
 ::*Start line 1 in Add field and Press "Add"
@@ Line 528: / Line 421: @@
 ::*From the "Application Type" drop-down list, select "GW\IP2IP"
 ::*Submit
 <br style="clear:both;" />
 == Inbound IP Routing ==
+The "IP to Trunk Group Routing Table" it used for define the routing inbound IP-to-IP calls.
-The "IP to Trunk Group Routing Table" it used for define the routing inbound IP-to-IP calls.<br>
 The table in which this is configured uses the IP Groups that you defined before.
-<br>
-<br>
-:In the "IP to Trunk Group Routing Table" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Routing Tables''' submenu -> '''IP to Trunk Group Routing''' page):<br>
-[[Image:IP-to-Tel-Routing.jpg|thumb|350px|Inbound IP Routing]]
+:In the "IP to Trunk Group Routing Table" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Routing Tables''' submenu -> '''IP to Trunk Group Routing''' page):
+[[Image:IP-to-Tel-Routing.jpg|left|thumb|500px|Inbound IP Routing]]
+<br style="clear:both;" />
 :*Index#1 for AlpahCom XE7
@@ Line 562: / Line 453: @@
 == Outbound IP Routing ==
+The "Tel to IP Routing Table" it used for define the routing outbound IP-to-IP calls.
-The "Tel to IP Routing Table" it used for define the routing outbound IP-to-IP calls.<br>
 The table in which this is configured uses the IP Groups that you defined before.
-<br>
-<br>
-:In the "Tel to IP Routing" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Routing Tables''' submenu -> '''Tel to IP Routing''' page):<br>
-[[Image:Tel-to-IP-Routing.jpg|thumb|350px|Outbound IP Routing]]
+:In the "Tel to IP Routing" page ('''Configuration''' tab -> '''Protocol Configuration''' menu -> '''Routing Tables''' submenu -> '''Tel to IP Routing''' page):
+[[Image:Tel-to-IP-Routing.jpg|left|thumb|500px|Outbound IP Routing]]
+<br style="clear:both;" />
 :*Index#1 from AlpahCom XE7 to SIPServer
 ::*Src.IPGroupID : select "1" to indicate received (inbound) calls identified as belonging to the IP Group configured for AlphaCom
@@ Line 586: / Line 475: @@
 <br style="clear:both;" />
 == Manipulation Table ==
-[[Image:Manipulation-table-Outgoing-call.jpg|thumb|350px|Manipulation Tel->IP Calls]]
+This step will change the local SIP ID/Dir No to number associated to SIP accounts.
-This step will change the local SIP ID/Dir No to number associated to SIP accounts.
-<br>
-<br>
 :In the "Source Number Tel->IP" page ('''VoIP''' tab -> '''Control Network''' menu -> '''GW and IP to IP''' submenu -> '''Manipulation''' page):
+[[Image:Manipulation-table-Outgoing-call.jpg|left|thumb|500px|Manipulation Tel->IP Calls]]
+<br style="clear:both;" />
 :*Manipulation Table for Outgoing Calls
+----
-[[Image:Manipulation-table-inncoming-call.jpg|thumb|350px|Manipulation IP-> Tel Calls]]
 This step is necessary to route inncoming call to right Extension on AlphaCom side.
-<br>
-<br>
 :In the "Dest Number IP->Tel" page ('''VoIP''' tab -> '''Control Network''' menu -> '''GW and IP to IP''' submenu -> '''Manipulation''' page):<br>
+[[Image:Manipulation-table-inncoming-call.jpg|left|thumb|500px|Manipulation IP-> Tel Calls]]
+<br style="clear:both;" />
 :*Manipulation Table for route the inncoming call
 ::*Submit
@@ Line 641: / Line 527: @@
 <br/>
 <br/>
-For configuration of the Cisco Call Manager please see [[Configuration guide for Cisco Call Manager 6]].
+For configuration of the Cisco Call Manager please see [[Cisco Call Manager 6 configuration guide]].
 The following highlighted points deviate from the standard CUCM configuration and are special for the SIP2SIP transcoding with AlphaCom using AudioCodes Mediant 600:
 == Configure a Region ==
-[[Image:SIP2SIP-Cisco-Region.PNG|350px|thumb|Region Configuration]]
+[[Image:SIP2SIP-Cisco-Region.PNG|left|500px|thumb|Region Configuration]]
+<br style="clear:both;" />
 :System -> Region -> Add New
 ::*Name: Zenitel
@@ Line 657: / Line 544: @@
 == Configure a SIP Trunk ==
-[[Image:CiscoSipTrunk 1.PNG|thumb|350px|Trunk Configuration]]
+[[Image:CiscoSipTrunk 1.PNG|left|thumb|500px|Trunk Configuration]]
-[[Image:CiscoSipTrunk 2.PNG|thumb|350px|Trunk Configuration, continued]]
+<br style="clear:both;" />
-[[Image:SIP2SIP-Cisco-SIPTrunk.PNG|thumb|350px|Trunk Configuration, continued]]
+[[Image:CiscoSipTrunk 2.PNG|left|thumb|500px|Trunk Configuration, continued]]
+<br style="clear:both;" />
+[[Image:SIP2SIP-Cisco-SIPTrunk.PNG|left|thumb|500px|Trunk Configuration, continued]]
+<br style="clear:both;" />
 :Device -> Trunk -> Add New
 ::*Trunk Type: SIP Trunk
@@ Line 687: / Line 577: @@
 == SIP settings ==
-[[Image:MV-370-SIP.PNG|thumb|SIP Settings]]
+[[Image:MV-370-SIP.PNG|left|thumb|500px|SIP Settings]]
+<br style="clear:both;" />
 In the menu '''SIP Settings -> Service Domain''', enter information for "Realm 1":
 :*'''Active''' = ON
@@ Line 699: / Line 590: @@
 == Codec settings ==
-[[Image:MV-370-Codec.PNG|thumb|Codec Settings]]
+[[Image:MV-370-Codec.PNG|left|thumb|500px|Codec Settings]]
+<br style="clear:both;" />
 In the menu '''SIP Settings -> Codec Settings''', set codec priority:
 :*'''Codec Priority 1:''' = G.729
@@ Line 706: / Line 598: @@
-[[Category:SIP]]
+[[Category:AlphaCom - SIP Integration]]
 [[Category:3rd party integration]]