Difference between revisions of "Turbine Extended series board connectors"
From Zenitel Wiki
(Created page with "{{AEIS}} <br clear=all/> thumb|left|500px|Turbine Extended connectors <br clear=all/> {| border="1" } | align="center" style="backgrou...") |
|||
| (One intermediate revision by the same user not shown) | |||
| Line 23: | Line 23: | ||
| 6 || TA-10 connector || Connection for [[TA-10]] Relay Module | | 6 || TA-10 connector || Connection for [[TA-10]] Relay Module | ||
|- | |- | ||
| − | | 7¹ || Power Input || Optional 24VDC power input from external power supply (if PoE is not provided) | + | | 7¹ || Power Input || Optional 24VDC/0.5A power input from external power supply (if PoE is not provided) |
|- | |- | ||
| 8 || LAN Port || Dual 10/100Mbps RJ-45 port for Ethernet connection (inbuilt switch). PoE is supported | | 8 || LAN Port || Dual 10/100Mbps RJ-45 port for Ethernet connection (inbuilt switch). PoE is supported | ||
| Line 38: | Line 38: | ||
* Relay switching capacity: Max. 60 watt (Max voltage: 250VAC/220VDC. Max current: 2A) | * Relay switching capacity: Max. 60 watt (Max voltage: 250VAC/220VDC. Max current: 2A) | ||
* The 5,3V output can deliver 200mA current maximum}} | * The 5,3V output can deliver 200mA current maximum}} | ||
| − | <br | + | |
| + | {{Note| | ||
| + | If connected to two PoE-capable switches, only one of the ports will negotiate PoE; hence this is not a good solution for power redundancy (switch failure might lead to a reboot). Instead a “dumb” PoE injector (spare-pair power) should be used for the two Ethernet ports or a local 24 VDC local power backup. | ||
| + | <br>If used together with PoE the station can be powered by 24 VDC as a local power backup. | ||
| + | }} | ||
=== J9: Keyboard connector === | === J9: Keyboard connector === | ||
Latest revision as of 14:33, 2 July 2024
| Item | Description | Comment |
| 1¹ | 2 Relays | Double Throw (SPDT) relay contact with 60W switching power. Max: 250VAC/220VDC, 2A, 60W |
| 2¹ | I/O interface | 6 general purpose I/Os. Each I/O can be configured either as an input or 12mA LED driver output |
| 3¹ | Line Output | Balanced 600 ohm audio line out. Suitable for external induction loop amplifier, PA amplifiers etc |
| 4¹ | Speaker Output | Connection for 8 ohm loudspeaker |
| 5¹ | Microphone Input | Electret mic input |
| 6 | TA-10 connector | Connection for TA-10 Relay Module |
| 7¹ | Power Input | Optional 24VDC/0.5A power input from external power supply (if PoE is not provided) |
| 8 | LAN Port | Dual 10/100Mbps RJ-45 port for Ethernet connection (inbuilt switch). PoE is supported |
| 9 | AUX | Auxiliary connector for Handset and Headset, and Line IN * Headset/handset speaker (pin 6/7): Minimum 32 Ohms * Microphone input (pin 4/5): For electret type. Bias voltage is 1,25V. * Line In: Maximum input level is 1.228 Vrms (Professional line level). |
|
¹) Connectable conductors: 0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm². |
|
|
|
|
|
If connected to two PoE-capable switches, only one of the ports will negotiate PoE; hence this is not a good solution for power redundancy (switch failure might lead to a reboot). Instead a “dumb” PoE injector (spare-pair power) should be used for the two Ethernet ports or a local 24 VDC local power backup.
|
J9: Keyboard connector
Only available on TKIE-3. See keyboard matrix article for details.