Difference between revisions of "IP Flush Master -V2 Board Connectors"

Latest revision as of 08:51, 17 October 2024

This chapter gives details about connections and indications for:

Item	Description	Comment
P3	Pluggable screw connector	* 1/2 = Connection to internal loudspeaker (8ohm) * 3/4 = Relay * 5/6 = Not in use
P4	Pluggable screw connector	* 1/2/ = Input 1-3 * 4 = Common * 5/6 = Station LED (5=A, 6=C)
J1	D48 Expansion Module	RJ45 Connector to connect D48 modules, via I2C bus.
P14	External loudspeaker	3-pin screw connector for 8 ohm loudspeaker (max 5W). Operates in parallel with internal speaker.
J3	5VDC	5 volt DC output
P1	LAN Port	10/100Mbps RJ-45 port for connection to the network. Supports PoE (802.3af). Draws power from either spare line or signal line.
P2	AUX Port	10/100Mbps RJ-45 port for for auxiliary equipment such as PC and IP camera. PoE is not forwarded to this port.
P600	External Power Supply	2-pin screw connector for connecting external 24-48VDC power supply. Max 300mA.
J5	Display	20-pin ZIF connector for LCD display. Separate display panels are available as a kit of 5 units (order no. 1008099000).
P5	Keyboard	Solderpoints See details further down.
J4	Keyboard	18 pin ZIF connector. See details further down.
J8	Handset/Headset	Dual RJ11 for Handset and Headset. See details further down.
J7	Gooseneck	3-pin header for connecting gooseneck microphone. 1 is +, 2 is - and 3 is GND.
S1	Microphone selector	Slide switch to select internal microphone (int) or gooseneck microphone (ext)
J10	Microphone	Internal microphone. Pin 1 is + and 2 is -.

Inputs

When "Station Type" is set as Master station in AlphaPro, the inputs are mapped as DAK 11, 12 and 13.
When the "Station Type" is set as CRM in AlphaPro, the inputs are mapped as 251, 252 and 253.

Keyboard matrix

P5 or J4 keyboard matrix

P5 pinnings:

Pinout on P5

J4 connector In software you can choose between four different matrix types, see Keyboard Settings.

18-pin ZIF-connector for keyboard. The keyboard may have up to 10 dialling keys, M and C keys, 10 DAK keys, 10 soft keys, volume up/down and light dim up/down keys connected in a matrix according to the drawing.

J4

J4/10 DAK1 Green LED
J4/11 DAK1 Red LED
J4/12 DAK2 Green LED
J4/13 DAK2 Red LED
J4/14 DAK3 Green LED
J4/15 DAK3 Red LED
J4/16 DAK4 Green LED
J4/17 DAK4 Red LED
J4/18 Common +3.3 V

Handset and Headset

Handset can optionally be connected via J11, J12 and J13.

J11, J12 & J13 - Handset

Pin header for handset connection. Same as J8 pin 1 - 6.

J11, J12, J13

J11 Pin 1 Spk+
J11 Pin 2 Spk-
J12 Pin 1 Mic+
J12 Pin 2 Mic-
J13 Pin 1 OFFHOOK
J13 Pin 2 GND

Handset:

J8

Pin 1 Mic+
Pin 2 Spk+
Pin 3 Spk- (0 V)
Pin 4 Mic-
Pin 5 Hook-switch (must be connected to pin 6 via a switch)
Pin 6 Hook-switch Ground

Headset:

J8

Pin 7 Mic+
Pin 8 Spk+
Pin 9 Spk-
Pin 10 Mic-
Pin 11 PTT Ground
Pin 12 PTT (Not currently supported by SW)

Relay switching capacity: Max. 60 watt (Max voltage: 250VAC/220VDC. Max current: 2A)

@@ Line 1: / Line 1: @@
 {{AEIS}}This chapter gives details about connections and indications for:
-*[[IP Flush Master -V2]]
-[[File:IPFlushMasterKitPCB.png|right]]
+*[[IP Flush Master -V2]]
+*[[IP-CROR]]
+*[[IP Master Station Kit - 1008493000|IP Master Station Kit -V2]]
+<br clear=all/>
+__NOTOC__
-====P1 LAN port & P2 AUX port====
+[[File:IPFlushDrawingwith numbers.png|thumb|left|800px]]
-<u>'''P1:'''</u>
+<br clear=all/>
-LAN connector for 10/100 Mbit Ethernet connection. The station can be powered from this connection if the line supports Power over Ethernet (PoE).
+{| border="1" }
+| align="center" style="background:#ffd400;" |'''Item'''
+| align="center" style="background:#ffd400;" |'''Description'''
+| align="center" style="background:#ffd400;" |'''''Comment'''''
+|-
+| P3 || Pluggable screw connector || * 1/2 = Connection to internal loudspeaker (8ohm) <br> * 3/4 = Relay <br> * 5/6 = Not in use
+|-
+| P4 || Pluggable screw connector || * 1/2/ = Input 1-3 <br> * 4 = Common <br> * 5/6 = Station LED (5=A, 6=C)
+|-
+| J1 || [[IP Flush Master DAK-48 Module|D48 Expansion Module]] || RJ45 Connector to connect D48 modules, via I2C bus.
+|-
+| P14 || External loudspeaker || 3-pin screw connector for 8 ohm loudspeaker (max 5W). Operates in parallel with internal speaker.
+|-
+| J3 || 5VDC || 5 volt DC output
+|-
+| P1 || LAN Port || 10/100Mbps RJ-45 port for connection to the network. Supports PoE (802.3af). Draws power from either spare line or signal line.
+|-
+| P2 || AUX Port || 10/100Mbps RJ-45 port for for auxiliary equipment such as PC and IP camera. PoE is not forwarded to this port.
+|-
+| P600 || External Power Supply || 2-pin screw connector for connecting external 24-48VDC power supply. Max 300mA.
+|-
+| J5 || Display || 20-pin ZIF connector for LCD display. Separate display panels are available as a kit of 5 units (order no. 1008099000).
+|-
+| P5 || Keyboard || Solderpoints See details further down.
+|-
+| J4 || Keyboard || 18 pin ZIF connector. See details further down.
+|-
+| J8 || Handset/Headset || Dual RJ11 for Handset and Headset. See details further down.
+|-
+| J7 || Gooseneck || 3-pin header for connecting gooseneck microphone. 1 is +, 2 is - and 3 is GND.
+|-
+| S1 || Microphone selector || Slide switch to select internal microphone (int) or gooseneck microphone (ext)
+|-
+| J10 || Microphone || Internal microphone. Pin 1 is + and 2 is -.
+|-
+|}
-The connector has two LEDs in front where the right (R) LED indicates Ethernet speed and the left (L) LED verifies Ethernet link and traffic. (L and R as seen from the connector side)
+==Inputs==
+{{Note|
+* ''When "Station Type" is set as '''Master station''' in AlphaPro, the inputs are mapped as DAK '''11, 12''' and '''13'''.''
+* ''When the "Station Type" is set as '''CRM''' in AlphaPro, the inputs are mapped as '''251, 252''' and '''253'''.''
+}}
-<u>'''P2:'''</u>
+==Keyboard matrix==
+[[File:IP-StationWeb Keyboard Matrix Standard.PNG|left|thumb|300px|P5 or J4 keyboard matrix]]
-RJ45 connector for auxiliary equipment like IP camera, PC or a second IP station. This port does not have an individual IP address. It does not carry power for AUX equipment.
-[[File:IP Master Board 1.PNG|left|thumb|200px|P1/P2]]
 <br style="clear:both;" />
-====P3 - Internal Loudspeaker, Relay Output and External Power Input====
+'''P5 pinnings:'''
--pin plug-on screw terminal for external connections.
+[[File:IPFlushMasterPCB P5 new.png|left|thumb|300px|Pinout on P5]]
-[[File:IPFlushMasterPCB_P3.png|left|thumb|200px|P3]]
 <br style="clear:both;" />
-*Pin 1/2  Connect to the internal loudspeaker.
-**Typical impedance: 8 Ω
-**Recommended impedance: 6-25 Ω.
-*Pin 3/4  Internal NO relay contact for door lock control etc.
-*Pin 5/6  Not in use.
-====P4 - Inputs and Station LED====
--pin plug-on screw terminal for external connections.
-[[File:IP Master Board 3.PNG|thumb|left|200px|P4]]
-<br style="clear:both;" />
-*Pin 1/4  Input 1
-*Pin 2/4  Input 2
-*Pin 3/4  Input 3
-*Pin 5/6  Station LED for call message info.
-{{Note|
-* ''When "Station Type" is set as '''Master station''' in AlphaPro, the inputs are mapped as DAK '''11, 12''' and '''13'''.''
-* ''When the "Station Type" is set as '''CRM''' in AlphaPro, the inputs are mapped as '''251, 252''' and '''253'''.'' }}
-====J4/P5 - Keyboard and DAK LED====
-Keyboard matrix is available on connector J4. Pin 1-9 is used.
+'''J4 connector'''
 In software you can choose between four different matrix types, see [[Keyboard Settings]].
-[[File:IP-StationWeb Keyboard Matrix Standard.PNG|left|thumb|300px|"Standard matrix" pinout on J4]]
-<br style="clear:both;" />
-'''J4 - Keyboard matrix'''
 -pin ZIF-connector for keyboard. The keyboard may have up to 10 dialling keys, M and C keys, 10 DAK keys, 10 soft keys, volume up/down and light dim up/down keys connected in a matrix according to the drawing.
@@ Line 55: / Line 68: @@
 <br style="clear:both;" />
-'''P5 - Keyboard'''
+*J4/10   DAK1 Green LED
-[[File:IPFlushMasterPCB P5.png|left|thumb|300px|Pinout on P5]]
+*J4/11   DAK1 Red LED
-<br style="clear:both;" />
+*J4/12   DAK2 Green LED
+*J4/13   DAK2 Red LED
-'''J4 - DAK LED connection'''
+*J4/14   DAK3 Green LED
+*J4/15   DAK3 Red LED
-Optional DAK LED connection.
+*J4/16   DAK4 Green LED
+*J4/17   DAK4 Red LED
-*J4/10   DAK1 Green LED
-*J4/11   DAK1 Red LED
-*J4/12   DAK2 Green LED
-*J4/13   DAK2 Red LED
-*J4/14   DAK3 Green LED
-*J4/15   DAK3 Red LED
-*J4/16   DAK4 Green LED
-*J4/17   DAK4 Red LED
 *J4/18   Common +3.3 V
-The DAK keys and the DAK LEDs are programmed using IND commands in the Event Handler. DAKs 1 to 4 and Soft keys 1 to 4 are used in current master stations.
-Privacy on/off is accomplished by pressing the C key for 3 seconds. A circled ''P'' is shown in the display during Privacy mode.
-<br style="clear:both;" />
-====J5 - Display====
+==Handset and Headset==
--pin ZIF connector for LCD display. Separate display panels are available as a kit of 5 units (order no. 100 8099 000).
+''Handset can optionally be connected via J11, J12 and J13.''
-<br style="clear:both;" />
-====J1 - DAK48 Module====
+'''J11, J12 & J13 - Handset'''
-RJ45 Connector for I2C interface. Used for connection of DAK modules.
-[[File:IP Master Board 5.PNG|left|thumb|200px|J1]]
-<br style="clear:both;" />
-*Pin 1  GND
-*Pin 2  A0 (GND)
-*Pin 3  A1 (GND)
-*Pin 4  NC (GND)
-*Pin 5  IRQ
-*Pin 6  SCL (Clock)
-*Pin 7  SDA (Data)
-*Pin 8  +13 V
-====J7 - Gooseneck Microphone====
+Pin header for handset connection. Same as J8 pin 1 - 6.
--pin header for connecting gooseneck microphone.
+[[File:IPFlushMasterPCB J11-13.png|left|thumb|400px|J11, J12, J13]]
-[[File:IP Master Board 6.PNG|left|thumb|200px|J7]]
 <br style="clear:both;" />
-*Pin 1  MIC+
-*Pin 2  MIC-
-*Pin 3  GND
-====J8 - Handset and Headset====
+*J11   Pin 1  Spk+
-Dual RJ11 for handset and headset. ''Handset can optionally be connected via J11, J12 and J13.''
+*J11   Pin 2  Spk-
+*J12   Pin 1  Mic+
+*J12   Pin 2  Mic-
+*J13   Pin 1  OFFHOOK
+*J13   Pin 2  GND
 <u>'''Handset:'''</u>
 [[File:IP Master Board 7.PNG|left|thumb|200px|J8]]
 <br style="clear:both;" />
-*Pin 1  Mic+
-*Pin 2  Spk+
+*Pin 1  Mic+
-*Pin 3  Spk- (0 V)
+*Pin 2  Spk+
-*Pin 4  Mic-
+*Pin 3  Spk- (0 V)
-*Pin 5  Hook-switch (must be connected to pin 6 via a switch)
+*Pin 4  Mic-
+*Pin 5  Hook-switch (must be connected to pin 6 via a switch)
 *Pin 6   Hook-switch Ground
@@ Line 118: / Line 108: @@
 [[File:IP Master Board 8.PNG|left|thumb|200px|J8]]
 <br style="clear:both;" />
-*Pin 7  Mic+
-*Pin 8  Spk+
+*Pin 7  Mic+
-*Pin 9  Spk-
+*Pin 8  Spk+
-*Pin 10   Mic-
+*Pin 9  Spk-
-*Pin 11   PTT Ground
+*Pin 10   Mic-
+*Pin 11   PTT Ground
 *Pin 12   PTT (Not currently supported by SW)
-==== P14 - External loudspeaker ====
+{{Note|
--pin screw connector for connecting external loudspeaker.
+Relay switching capacity: Max. 60 watt (Max voltage: 250VAC/220VDC. Max current: 2A)
-*For connection of external 8 ohm speaker (max 5W)
+}}
-*Operates in parallel with built-in speaker
+<br clear=all/>
-*Pin 2/3: 8 Ohm loudspeaker
-====J10 - Microphone====
-Internal microphone
-[[File:IP Master Board 10.PNG|left|thumb|200px|J10]]
-<br style="clear:both;" />
-*Pin 1  MIC+
-*Pin 2  MIC-
-====J11, J12 & J13 - Handset====
-Pin header for handset connection. Same as J8 pin 1 - 6.
-[[File:IP Master Board 11.PNG|left|thumb|200px|J11, J12, J13]]
-<br style="clear:both;" />
-*J11   Pin 1   Spk+
-*J11   Pin 2  Spk-
-*J12   Pin 1  Mic+
-*J12   Pin 2  Mic-
-*J13   Pin 1  OFFHOOK
-*J13   Pin 2  GND
-*J13   Pin 3  PTT (Not currently supported by SW)
-====S1 - Microphone Selection====
-Slide-switch to select internal microphone (Int) or gooseneck microphone (Ext).
-[[File:IP Master Board 12.PNG|left|thumb|200px|S1]]
-<br style="clear:both;" />
 [[Category:Turbine Connections]]

Difference between revisions of "IP Flush Master -V2 Board Connectors"

From Zenitel Wiki

Latest revision as of 08:51, 17 October 2024

Inputs

Keyboard matrix

Handset and Headset