Difference between revisions of "IP Flush Master -V2 Board Connectors"

Latest revision as of 08:51, 17 October 2024

This chapter gives details about connections and indications for:

Item	Description	Comment
P3	Pluggable screw connector	* 1/2 = Connection to internal loudspeaker (8ohm) * 3/4 = Relay * 5/6 = Not in use
P4	Pluggable screw connector	* 1/2/ = Input 1-3 * 4 = Common * 5/6 = Station LED (5=A, 6=C)
J1	D48 Expansion Module	RJ45 Connector to connect D48 modules, via I2C bus.
P14	External loudspeaker	3-pin screw connector for 8 ohm loudspeaker (max 5W). Operates in parallel with internal speaker.
J3	5VDC	5 volt DC output
P1	LAN Port	10/100Mbps RJ-45 port for connection to the network. Supports PoE (802.3af). Draws power from either spare line or signal line.
P2	AUX Port	10/100Mbps RJ-45 port for for auxiliary equipment such as PC and IP camera. PoE is not forwarded to this port.
P600	External Power Supply	2-pin screw connector for connecting external 24-48VDC power supply. Max 300mA.
J5	Display	20-pin ZIF connector for LCD display. Separate display panels are available as a kit of 5 units (order no. 1008099000).
P5	Keyboard	Solderpoints See details further down.
J4	Keyboard	18 pin ZIF connector. See details further down.
J8	Handset/Headset	Dual RJ11 for Handset and Headset. See details further down.
J7	Gooseneck	3-pin header for connecting gooseneck microphone. 1 is +, 2 is - and 3 is GND.
S1	Microphone selector	Slide switch to select internal microphone (int) or gooseneck microphone (ext)
J10	Microphone	Internal microphone. Pin 1 is + and 2 is -.

Inputs

When "Station Type" is set as Master station in AlphaPro, the inputs are mapped as DAK 11, 12 and 13.
When the "Station Type" is set as CRM in AlphaPro, the inputs are mapped as 251, 252 and 253.

Keyboard matrix

P5 or J4 keyboard matrix

P5 pinnings:

Pinout on P5

J4 connector In software you can choose between four different matrix types, see Keyboard Settings.

18-pin ZIF-connector for keyboard. The keyboard may have up to 10 dialling keys, M and C keys, 10 DAK keys, 10 soft keys, volume up/down and light dim up/down keys connected in a matrix according to the drawing.

J4

J4/10 DAK1 Green LED
J4/11 DAK1 Red LED
J4/12 DAK2 Green LED
J4/13 DAK2 Red LED
J4/14 DAK3 Green LED
J4/15 DAK3 Red LED
J4/16 DAK4 Green LED
J4/17 DAK4 Red LED
J4/18 Common +3.3 V

Handset and Headset

Handset can optionally be connected via J11, J12 and J13.

J11, J12 & J13 - Handset

Pin header for handset connection. Same as J8 pin 1 - 6.

J11, J12, J13

J11 Pin 1 Spk+
J11 Pin 2 Spk-
J12 Pin 1 Mic+
J12 Pin 2 Mic-
J13 Pin 1 OFFHOOK
J13 Pin 2 GND

Handset:

J8

Pin 1 Mic+
Pin 2 Spk+
Pin 3 Spk- (0 V)
Pin 4 Mic-
Pin 5 Hook-switch (must be connected to pin 6 via a switch)
Pin 6 Hook-switch Ground

Headset:

J8

Pin 7 Mic+
Pin 8 Spk+
Pin 9 Spk-
Pin 10 Mic-
Pin 11 PTT Ground
Pin 12 PTT (Not currently supported by SW)

Relay switching capacity: Max. 60 watt (Max voltage: 250VAC/220VDC. Max current: 2A)

@@ Line 4: / Line 4: @@
 *[[IP-CROR]]
 *[[IP Master Station Kit - 1008493000|IP Master Station Kit -V2]]
+<br clear=all/>
+__NOTOC__
-[[File:IPFlushMasterKitPCB2.png|700px|right]]
+[[File:IPFlushDrawingwith numbers.png|thumb|left|800px]]
+<br clear=all/>
-====P1 - LAN port & P2 AUX port====
+{| border="1" }
-<u>'''P1:'''</u>
+| align="center" style="background:#ffd400;" |'''Item'''
+| align="center" style="background:#ffd400;" |'''Description'''
-LAN connector for 10/100 Mbit Ethernet connection. The station can be powered from this connection if the line supports Power over Ethernet (PoE).
+| align="center" style="background:#ffd400;" |'''''Comment'''''
+|-
-The connector has two LEDs in front where the right (R) LED indicates Ethernet speed and the left (L) LED verifies Ethernet link and traffic. (L and R as seen from the connector side)
+| P3 || Pluggable screw connector || * 1/2 = Connection to internal loudspeaker (8ohm) <br> * 3/4 = Relay <br> * 5/6 = Not in use
+|-
-<u>'''P2:'''</u>
+| P4 || Pluggable screw connector || * 1/2/ = Input 1-3 <br> * 4 = Common <br> * 5/6 = Station LED (5=A, 6=C)
+|-
-RJ45 connector for auxiliary equipment like IP camera, PC or a second IP station. This port does not have an individual IP address. It does not carry power for AUX equipment.
+| J1 || [[IP Flush Master DAK-48 Module|D48 Expansion Module]] || RJ45 Connector to connect D48 modules, via I2C bus.
-[[File:IP Master Board 1.PNG|left|thumb|200px|P1/P2]]
+|-
-<br style="clear:both;" />
+| P14 || External loudspeaker || 3-pin screw connector for 8 ohm loudspeaker (max 5W). Operates in parallel with internal speaker.
+|-
-====P3 - Internal Loudspeaker, Relay Output and External Power Input====
+| J3 || 5VDC || 5 volt DC output
--pin plug-on screw terminal for external connections.
+|-
-[[File:IPFlushMasterPCB_P3.png|left|thumb|200px|P3]]
+| P1 || LAN Port || 10/100Mbps RJ-45 port for connection to the network. Supports PoE (802.3af). Draws power from either spare line or signal line.
-<br style="clear:both;" />
+|-
+| P2 || AUX Port || 10/100Mbps RJ-45 port for for auxiliary equipment such as PC and IP camera. PoE is not forwarded to this port.
-*Pin 1/2  Connect to the internal loudspeaker.
+|-
-**Typical impedance: 8 Ω
+| P600 || External Power Supply || 2-pin screw connector for connecting external 24-48VDC power supply. Max 300mA.
-**Recommended impedance: 6-25 Ω.
+|-
-*Pin 3/4  Internal NO relay contact for door lock control etc.
+| J5 || Display || 20-pin ZIF connector for LCD display. Separate display panels are available as a kit of 5 units (order no. 1008099000).
-*Pin 5/6  Not in use.
+|-
+| P5 || Keyboard || Solderpoints See details further down.
-====P4 - Inputs and Station LED====
+|-
--pin plug-on screw terminal for external connections.
+| J4 || Keyboard || 18 pin ZIF connector. See details further down.
-[[File:IP Master Board 3.PNG|thumb|left|200px|P4]]
+|-
-<br style="clear:both;" />
+| J8 || Handset/Headset || Dual RJ11 for Handset and Headset. See details further down.
+|-
-*Pin 1/4  Input 1
+| J7 || Gooseneck || 3-pin header for connecting gooseneck microphone. 1 is +, 2 is - and 3 is GND.
-*Pin 2/4  Input 2
+|-
-*Pin 3/4  Input 3
+| S1 || Microphone selector || Slide switch to select internal microphone (int) or gooseneck microphone (ext)
-*Pin 5/6  Station LED for call message info.
+|-
+| J10 || Microphone || Internal microphone. Pin 1 is + and 2 is -.
+|-
+|}
+==Inputs==
 {{Note|
 * ''When "Station Type" is set as '''Master station''' in AlphaPro, the inputs are mapped as DAK '''11, 12''' and '''13'''.''
-* ''When the "Station Type" is set as '''CRM''' in AlphaPro, the inputs are mapped as '''251, 252''' and '''253'''.'' }}
+* ''When the "Station Type" is set as '''CRM''' in AlphaPro, the inputs are mapped as '''251, 252''' and '''253'''.''
+}}
-====P5 - Keyboard====
+==Keyboard matrix==
-[[File:IPFlushMasterPCB P5 new.png|left|thumb|300px|Pinout on P5]]
+[[File:IP-StationWeb Keyboard Matrix Standard.PNG|left|thumb|300px|P5 or J4 keyboard matrix]]
-<br style="clear:both;" />
-[[File:IP-StationWeb Keyboard Matrix Standard.PNG|left|thumb|300px|P5 keyboard matrix]]
 <br style="clear:both;" />
-====P14 - External loudspeaker====
+'''P5 pinnings:'''
--pin screw connector for connecting external 8 ohm loudspeaker, max 5W. Operates in parallel with built-in speaker.
+[[File:IPFlushMasterPCB P5 new.png|left|thumb|300px|Pinout on P5]]
-*Pin 2/3: 8 Ohm loudspeaker
-====J1 - DAK48 Module====
-RJ45 Connector for I2C interface. Used for connection of DAK modules.
-[[File:IP Master Board 5.PNG|left|thumb|200px|J1]]
 <br style="clear:both;" />
-*Pin 1  GND
+'''J4 connector'''
-*Pin 2  A0 (GND)
-*Pin 3  A1 (GND)
-*Pin 4  NC (GND)
-*Pin 5  IRQ
-*Pin 6  SCL (Clock)
-*Pin 7  SDA (Data)
-*Pin 8  +13 V (limited at 500 mA)
-====J4 - Keyboard and DAK LED====
-Keyboard matrix is available on connector J4. Pin 1-9 is used.
 In software you can choose between four different matrix types, see [[Keyboard Settings]].
-[[File:IP-StationWeb Keyboard Matrix Standard.PNG|left|thumb|300px|"Standard matrix" pinout on J4]]
-<br style="clear:both;" />
-'''J4 - Keyboard matrix'''
 -pin ZIF-connector for keyboard. The keyboard may have up to 10 dialling keys, M and C keys, 10 DAK keys, 10 soft keys, volume up/down and light dim up/down keys connected in a matrix according to the drawing.
@@ Line 96: / Line 78: @@
 *J4/18   Common +3.3 V
-The DAK keys and the DAK LEDs are programmed using IND commands in the Event Handler. DAKs 1 to 4 and Soft keys 1 to 4 are used in current master stations.
+==Handset and Headset==
+''Handset can optionally be connected via J11, J12 and J13.''
-Privacy on/off is accomplished by pressing the C key for 3 seconds. A circled ''P'' is shown in the display during Privacy mode.
+'''J11, J12 & J13 - Handset'''
-<br style="clear:both;" />
-====J5 - Display====
+Pin header for handset connection. Same as J8 pin 1 - 6.
--pin ZIF connector for LCD display. Separate display panels are available as a kit of 5 units (order no. 1008099000).
+[[File:IPFlushMasterPCB J11-13.png|left|thumb|400px|J11, J12, J13]]
 <br style="clear:both;" />
-====J7 - Gooseneck Microphone====
+*J11   Pin 1  Spk+
--pin header for connecting gooseneck microphone.
+*J11   Pin 2  Spk-
-[[File:IP Master Board 6.PNG|left|thumb|200px|J7]]
+*J12   Pin 1  Mic+
-<br style="clear:both;" />
+*J12   Pin 2  Mic-
+*J13   Pin 1  OFFHOOK
-*Pin 1  MIC+
+*J13   Pin 2  GND
-*Pin 2  MIC-
-*Pin 3  GND
-====J8 - Handset and Headset====
-Dual RJ11 for handset and headset. ''Handset can optionally be connected via J11, J12 and J13.''
 <u>'''Handset:'''</u>
@@ Line 139: / Line 116: @@
 *Pin 12   PTT (Not currently supported by SW)
-====J10 - Microphone====
+{{Note|
-Internal microphone
+Relay switching capacity: Max. 60 watt (Max voltage: 250VAC/220VDC. Max current: 2A)
-[[File:IP Master Board 10.PNG|left|thumb|200px|J10]]
+}}
-<br style="clear:both;" />
+<br clear=all/>
-*Pin 1  MIC+
-*Pin 2  MIC-
-====J11, J12 & J13 - Handset====
-Pin header for handset connection. Same as J8 pin 1 - 6.
-[[File:IPFlushMasterPCB J11-13.png|left|thumb|400px|J11, J12, J13]]
-<br style="clear:both;" />
-*J11   Pin 1  Spk+
-*J11   Pin 2  Spk-
-*J12   Pin 1  Mic+
-*J12   Pin 2  Mic-
-*J13   Pin 1  OFFHOOK
-*J13   Pin 2  GND
-====S1 - Microphone Selection====
-Slide-switch to select internal microphone (Int) or gooseneck microphone (Ext).
-[[File:IP Master Board 12.PNG|left|thumb|200px|S1]]
-<br style="clear:both;" />
 [[Category:Turbine Connections]]

Difference between revisions of "IP Flush Master -V2 Board Connectors"

From Zenitel Wiki

Latest revision as of 08:51, 17 October 2024

Inputs

Keyboard matrix

Handset and Headset