Actions

VSF-Fortitude8 9.1 Release Notes: Difference between revisions

From Zenitel Wiki

(Created page with "* Previous Release - VSF-Fortitude8 8.2 Release Notes This document provides the release notes for VSF-Fortitude8 9.0 with incremental bug fix releases. The release notes...")
 
No edit summary
 
(16 intermediate revisions by 2 users not shown)
Line 1: Line 1:
* Previous Release - [[VSF-Fortitude8 8.2 Release Notes]]
* Previous Release - [[VSF-Fortitude8 9.0 Release Notes]]
* Next Release - [[VSF-Fortitude8 9.2 Release Notes]]


This document provides the release notes for VSF-Fortitude8 9.0 with incremental bug fix releases. The release notes for VSF-Fortitude8 9.0 describe new features, improvements and issues fixed after VSF-Fortitude8 8.2.3.3.
This document provides the release notes for VSF-Fortitude8 9.1 with incremental bug fix releases. The release notes for VSF-Fortitude8 9.1 describe new features, improvements and issues fixed after VSF-Fortitude8 9.0.3.3.


==Release info==
==Release info==
Line 9: Line 10:
The firmware is delivered in two different files:
The firmware is delivered in two different files:


*vsff8-9.0.3.x - Used for standard in-field upgrades
*vsff8-9.1.3.x - Used for standard in-field upgrades
*vsff8-prod-9.0.3.x - Used in production- and recovery upgrades.
*vsff8-prod-9.1.3.x - Used in production- and recovery upgrades.


'''Version:''' 9.0.3.3<br>
'''Version:''' 9.1.3.4<br>
'''Date:''' 13.12.24 <br>
'''Date:''' 28.03.25 <br>
'''Status:''' General Availability<br>
'''Status:''' General Availability<br>


=VSF-FORTITUDE8 9.0.3.3=
=VSF-FORTITUDE8 9.1.3.4=
==Issues fixed==
==Issues fixed==
=== MTN-4511 Authentication is now required to access all web pages ===
=== DS-1319 Video stability issues ===
 
Sometimes the video stream as part of a SIP call would start after a short delay or not start at all. This has now been fixed
=== MTN-4454 Fixed issue where multicast paging configuration is lost after upgrade ===
As from 8.2.3.0, the multicast configuration in SIP and Edge mode is stored in a different format and would be lost on upgrade. From 9.0.3.3, configuration is transferred.


<br>
<br>


==Known Issues==
=VSF-FORTITUDE8 9.1.3.3=
=== MTN-4333 HD-Audio mode not working using digital microphone input ===
==Issues fixed==
Audio is distorted when digital microphone is used. Audio is OK if using analogue microphone input
=== DS-1386 The display settings for TEIV-1+ can now be configured from Zenitel Connect Pro.===
Settings for the OLED display in the TEIV-1+ station could not be configured from Zenitel Connect Pro server. This is now fixed


===MTN-4121 Known issue: Asterisk discards alternative profiles===
<br>
Default setting for ITSV-5 sends 3 types (BP & MP & HP). However, Asterisk discards all but the first profile it receives (HP in this case). Since only the "Baseline profile" is supported on the device the video doesn't load. A workaround to this issue is to select "Baseline profile" as the H.264 profile type on the ITSV-5.


The issue has been reported and documented here: https://issues.asterisk.org/jira/browse/ASTERISK-29182
=VSF-FORTITUDE8 9.1.3.2=
==Issues fixed==
=== DS-1075 Unable to configure long domain names for SIP servers ===
Previously users could only enter domain names up to 64 characters. Now supports domain names up to 253 characters long. On upgrade, all devices can handle longer domain names.


<br>


<br>


=VSF-FORTITUDE8 9.0.3.1=
=VSF-FORTITUDE8 9.1.3.1=
==Issues fixed==
==Issues fixed==
===MTN-4590 Multicast relay sometimes had issues working with multicast paging===
=== DS-1344 The device input 6 is now operating correctly.===
When devices were using SIP over UDP it could get multiple re-invites quickly that keep restarting media which in turn could mess up multicast paging on devices. As re-invites should not support media reconfiguration for multicast relay this is now disabled and paging works ok.  
Input 6 was not working after upgrading to 9.1.3.0. This is now fixed.
 
<br>


==Known Issues==
==Known Issues==
=== MTN-4333 HD-Audio mode not working using digital microphone input ===
=== MTN-4333 HD-Audio mode not working using digital microphone input ===
Audio is distorted when digital microphone is used. Audio is OK if using analogue microphone input
Audio is distorted when digital microphone is used. Audio is OK if using analogue microphone input
===MTN-4121 Known issue: Asterisk discards alternative profiles===
Default setting for ITSV-5 sends 3 types (BP & MP & HP). However, Asterisk discards all but the first profile it receives (HP in this case). Since only the "Baseline profile" is supported on the device the video doesn't load. A workaround to this issue is to select "Baseline profile" as the H.264 profile type on the ITSV-5.
The issue has been reported and documented here: https://issues.asterisk.org/jira/browse/ASTERISK-29182


<br>
<br>


=VSF-FORTITUDE8 9.0.3.0=
=VSF-FORTITUDE8 9.1.3.0=
==Improvements==
==Improvements==
===MTN-4558 RTSP/ONVIF backchannel loudspeaker audio feedback to mic RTSP channel===
===DS-1152 Added a configuration option in "Call Settings" in the device web for not encode the “#” as “%23” in sip invite URIs===
If a VMS system opens both the device loudspeaker backchannel and mic listen channel at the same time a full feedback will be heard on far-end. The loudspeaker backchannel is still routed outside AEC algorithm, but fixed for now by always muting mic RTP channel when backchannel is active. 
 
=== MTN-4397 Improved certificate handling, and split SIP and HTTPS certificates into separate pages===
Split SIP and HTTPS certificates into separate pages, removed turbine_server_sha1.key private key and TLS Private Key option, added factory reset handling, added backup and recovery for SIP certificates, fixed certificate regeneration on some devices, removed private keys from the device web page.


=== MTN-3557 New configuration option for RTSP Audio Source===  
=== DS-1055 Increased maximum operating temperature ===
There’s a new option for configuring RTSP Audio Source, “Mixed signal”. This option mixes far and near end signal.
The maximum operating temperature increased to 105°c, which will trigger a shutdown


=== DS-1034 Added support for codec L16x48 to Multicast Paging config===  
===DS-958 New option added to factory reset the device with keeping IP settings===
Devices can now listen to raw PCM 48 kHz audio stream (L16x48) when configured in HD-Audio mode.
With the new option under Main Settings page, it is now possible to factory reset the device with keeping IP, firewall and 802.1X settings.
 
=== DS-970 Added multicast relay feature===
Device can now relay incoming RTP to specified address and port.
 
=== DS-889 Operate output when the call button is pressed in idle===
Added option to configure operation of relays and outputs when the call button is pressed.


<br>
<br>


==Issues fixed==
==Issues fixed==
=== MTN-4563 Changing zoom setting caused video to stop working and device reboot===
=== DS-1317 The GPO event will now get published with correct GPIO pin. ===
When user changed video zoom setting from default one and rebooted device would get into reboot loop with video not working. Factory reset would had resolved it. This is now fixed.
 
=== MTN-4438 The 0,5 video zoom level is now available again===
The 0,5 video zoom level was missing in the device web in version 8.2. It is now available again.
 
=== MTN-4383 Added Missing SNMP traps on TCIV+===
Fixed missing “Input Button Pressed/Released“ option in Advanced Network on TCIV+ devices.
 
=== DS-1015 Permanent Audio Stream fixes and config refresh===
Some parts of the audio stream config was not working correct and mic level was very low. Also linked to RTSP “Audio Source” config for impact which signal is sent to RTP stream.
Consult wiki documentation for more details.


<br>
<br>
Line 97: Line 70:
=== MTN-4333 HD-Audio mode not working using digital microphone input ===
=== MTN-4333 HD-Audio mode not working using digital microphone input ===
Audio is distorted when digital microphone is used. Audio is OK if using analogue microphone input
Audio is distorted when digital microphone is used. Audio is OK if using analogue microphone input
===MTN-4121 Known issue: Asterisk discards alternative profiles===
Default setting for ITSV-5 sends 3 types (BP & MP & HP). However, Asterisk discards all but the first profile it receives (HP in this case). Since only the "Baseline profile" is supported on the device the video doesn't load. A workaround to this issue is to select "Baseline profile" as the H.264 profile type on the ITSV-5.
The issue has been reported and documented here: https://issues.asterisk.org/jira/browse/ASTERISK-29182




Latest revision as of 14:28, 7 November 2025

This document provides the release notes for VSF-Fortitude8 9.1 with incremental bug fix releases. The release notes for VSF-Fortitude8 9.1 describe new features, improvements and issues fixed after VSF-Fortitude8 9.0.3.3.

Release info

Name: VSF-Fortitude8
Description: VSF-Fortitude8 is a firmware for Zenitel devices based on the IMX8 processor.

The firmware is delivered in two different files:

  • vsff8-9.1.3.x - Used for standard in-field upgrades
  • vsff8-prod-9.1.3.x - Used in production- and recovery upgrades.

Version: 9.1.3.4
Date: 28.03.25
Status: General Availability

VSF-FORTITUDE8 9.1.3.4

Issues fixed

DS-1319 Video stability issues

Sometimes the video stream as part of a SIP call would start after a short delay or not start at all. This has now been fixed


VSF-FORTITUDE8 9.1.3.3

Issues fixed

DS-1386 The display settings for TEIV-1+ can now be configured from Zenitel Connect Pro.

Settings for the OLED display in the TEIV-1+ station could not be configured from Zenitel Connect Pro server. This is now fixed


VSF-FORTITUDE8 9.1.3.2

Issues fixed

DS-1075 Unable to configure long domain names for SIP servers

Previously users could only enter domain names up to 64 characters. Now supports domain names up to 253 characters long. On upgrade, all devices can handle longer domain names.



VSF-FORTITUDE8 9.1.3.1

Issues fixed

DS-1344 The device input 6 is now operating correctly.

Input 6 was not working after upgrading to 9.1.3.0. This is now fixed.

Known Issues

MTN-4333 HD-Audio mode not working using digital microphone input

Audio is distorted when digital microphone is used. Audio is OK if using analogue microphone input


VSF-FORTITUDE8 9.1.3.0

Improvements

DS-1152 Added a configuration option in "Call Settings" in the device web for not encode the “#” as “%23” in sip invite URIs

DS-1055 Increased maximum operating temperature

The maximum operating temperature increased to 105°c, which will trigger a shutdown

DS-958 New option added to factory reset the device with keeping IP settings

With the new option under Main Settings page, it is now possible to factory reset the device with keeping IP, firewall and 802.1X settings.


Issues fixed

DS-1317 The GPO event will now get published with correct GPIO pin.


Known Issues

MTN-4333 HD-Audio mode not working using digital microphone input

Audio is distorted when digital microphone is used. Audio is OK if using analogue microphone input



Retrieved from "https://wiki.zenitel.com/w/index.php?title=VSF-Fortitude8_9.1_Release_Notes&oldid=241215"
MediaWiki spam blocked by CleanTalk.