Difference between revisions of "Dynamic group call"
From Zenitel Wiki
| Line 23: | Line 23: | ||
*Put all CRM IV’s that should have Dynamic Group Call feature in UDP group 1. | *Put all CRM IV’s that should have Dynamic Group Call feature in UDP group 1. | ||
| − | Event Handler programming | + | ===Event Handler programming=== |
| + | Event 1: | ||
{| | {| | ||
|- | |- | ||
| Line 42: | Line 43: | ||
|} | |} | ||
| + | |||
| + | Event 2: | ||
{| | {| | ||
|- | |- | ||
| Line 87: | Line 90: | ||
|} | |} | ||
| + | Event 3: | ||
| + | {| | ||
| + | |- | ||
| + | |width="100pt"|'''Event Owner''': | ||
| + | |width="300pt"|Stations w/UDP 1 (CRM IV stations) | ||
| + | |- | ||
| + | |'''Event type''': || 08 – Conversation Outgoing | ||
| + | |- | ||
| + | |'''Subevent''': || 0 | ||
| + | |- | ||
| + | |'''When change to''': || OFF | ||
| + | |- | ||
| + | |'''When related to''': || All | ||
| + | |- | ||
| + | |'''Action''': || IF %op(%2.dir,=,%1.exp) | ||
| + | |- | ||
| + | | || IF %gns(%1.exp(2),0) | ||
| + | |- | ||
| + | | || $ER U15 U1 U1 U1 N%gns(%1.exp(2),0) U3 %1.ref | ||
| + | |- | ||
| + | | || ENDIF | ||
| + | |- | ||
| + | | || ENDIF | ||
| + | |- | ||
| + | |} | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Revision as of 16:30, 7 December 2007
Operation (CRM IV)
- Press the "Group Config." button, red led in key starts flashing
- Select subscribers to be included / excluded (toggle function), flashing green led in key indicate included
- Press the "Group Config." button again, the group call is activated, red led in key stops flashing
- The green leds continue to flash during the group call
- When the group call is cancelled the group is emptied, and the green leds stop flashing
LIMITATION: You can only include subscribers, you cannot include groups!
Programming
- Software requirement: AMC 8.26 is later
- If not already existing, create 9535 = feature 95/0. The "Group Config." DAK button is programmed to 9535.
- Each CRMIV must “own” a group call that nobody else uses. The directory number of the group call should be changed so that the two last digits are identical to the group index number.
Example:
- Group 2 = 8502
- Group 10 = 8510
Etc.
- Enter the group call directory number associated to the CRMIV in the External Parameter (%1.EXP) field of the CRM IV.
- Put all CRM IV’s that should have Dynamic Group Call feature in UDP group 1.
Event Handler programming
Event 1:
| Event Owner: | Stations w/UDP 1 (CRM IV stations) |
| Event type: | 15 – Event Trigger |
| Subevent: | 0 |
| When change to: | ON or OFF |
| When related to: | Directory number: 9535 |
| Action: | IND %1.phy %1.dak(I%2.dir) 1 3 |
Event 2:
| Event Owner: | Stations w/UDP 1 (CRM IV stations) |
| Event type: | 25 – Event trigger with parameter |
| Subevent: | 0 |
| When change to: | ON or OFF |
| When related to: | All |
| Action: | IF %sgm(%2.phy,%1.exp(2)) |
| IND %1.phy %1.dak(I%2.dir) 2 3 OFF | |
| ENDIF | |
| IF %op(%sgm(%2.phy,%1.exp(2)),=,0) | |
| IND %1.phy %1.dak(I%2.dir) 2 3 ON | |
| ENDIF | |
| $GRM L%2.dir NG%1.exp(2) U2 | |
| IF %op(%2.dir,=,9535) | |
| $DISCON_ST L%1.dir 0 | |
| IND %1.phy %1.dak(I%2.dir) 2 3 OFF | |
| pause | |
| pause | |
| pause | |
| $DD L%1.dir L%1.exp | |
| ENDIF |
Event 3:
| Event Owner: | Stations w/UDP 1 (CRM IV stations) |
| Event type: | 08 – Conversation Outgoing |
| Subevent: | 0 |
| When change to: | OFF |
| When related to: | All |
| Action: | IF %op(%2.dir,=,%1.exp) |
| IF %gns(%1.exp(2),0) | |
| $ER U15 U1 U1 U1 N%gns(%1.exp(2),0) U3 %1.ref | |
| ENDIF | |
| ENDIF |
Owner: Stations w/UDP 8 (All stations) Event type: 15 – Event Trigger Subtype: 1 (NOTE: Subtype 1, NOT 0) When Change to: ON When Related to: All Action: $GRM N%gns(%2.exp(2),0) NG %2.exp(2) U0 IND %2.phy %2.dak(I%1.dir) 2 3 OFF pause IF %gns(%2.exp(2),0) $ER U15 U1 U1 U1 N%gns(%2.exp(2),0) U3 %2.ref ENDIF