Difference between revisions of "VOIP AUDIO CONFIG"
From Zenitel Wiki
| (5 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
| − | {{ | + | {{AI}} |
{| border="1" | {| border="1" | ||
|- | |- | ||
| Line 9: | Line 9: | ||
|colspan="3"|'''$VAC L101 U6 '10.5.11.32' W1234 W4322 '''|| colspan="2"|Configure the IP audio parameters for station 101, G.711u to 10.5.11.32 port 1234, incoming audio to AlphaCom on port 4322. | |colspan="3"|'''$VAC L101 U6 '10.5.11.32' W1234 W4322 '''|| colspan="2"|Configure the IP audio parameters for station 101, G.711u to 10.5.11.32 port 1234, incoming audio to AlphaCom on port 4322. | ||
|- | |- | ||
| − | |colspan="5"|$VAC configure the RTP audio stream for "RTP-stream station", to activate the audio the station must be called or controlled by $CONN etc. <br> Note that RTP uses even port numbers, and RTCP uses odd port numbers. So it must be at least 2 between source and destination port. E.g. 2000, 2002 etc. | + | |colspan="5"|$VAC configure the RTP audio stream for "RTP-stream station", to activate the audio the station must be called or controlled by $CONN etc. <br> Note that RTP uses even port numbers, and RTCP uses odd port numbers. So it must be at least 2 between source and destination port. E.g. 2000, 2002 etc.<br> Often used together with [[IP Dummy Station]]. |
|- | |- | ||
| Line 26: | Line 26: | ||
|} | |} | ||
| − | |||
| − | |||
| − | |||
By default the RTP stream station is "REGISTERED" during system start up. If manual registration is needed the system flag "RTP_stream_man_reg" can be used. If set the RTP stream station is down until the first "$VAC" command is received. | By default the RTP stream station is "REGISTERED" during system start up. If manual registration is needed the system flag "RTP_stream_man_reg" can be used. If set the RTP stream station is down until the first "$VAC" command is received. | ||
| + | {{code|<nowiki>&000204 .ex_profile.flags.RTP_stream_man_reg = 0 (0x00000000)</nowiki>}} | ||
<br/> | <br/> | ||
==Group Call and Program Conference== | ==Group Call and Program Conference== | ||
When the RTP-stream station is included in a group call or program conference the RTP stream is sent to the destination IP address as specified in param 3 of $VAC. The IP port used is the port specified for IP station Group Call and Program Conference. | When the RTP-stream station is included in a group call or program conference the RTP stream is sent to the destination IP address as specified in param 3 of $VAC. The IP port used is the port specified for IP station Group Call and Program Conference. | ||
| − | + | {{code|<nowiki>ex_profile.ip_config.ip_st_audio_group = 61002 (0xee4a)</nowiki> }} | |
| − | + | {{code|<nowiki>ex_profile.ip_config.ip_st_audio_prog = 61004 (0xee4c)</nowiki>}} | |
<br> | <br> | ||
| Line 43: | Line 41: | ||
[[Category: ACDP messages]] | [[Category: ACDP messages]] | ||
| − | [[Category:Audio Messaging]] | + | [[Category: Audio Messaging]] |
| − | + | [[Category: DP Commands]] | |
[[AlphaNet_Data_Protocol#Station_Connect_Operations|Back to AlphaNet message list]] | [[AlphaNet_Data_Protocol#Station_Connect_Operations|Back to AlphaNet message list]] | ||
Latest revision as of 09:48, 20 January 2023
| VAC (VOIP_AUDIO_CONFIG) | 0x00AF | 175 | AMC 11.02 | |
|---|---|---|---|---|
| $VAC L101 U6 '10.5.11.32' W1234 W4322 | Configure the IP audio parameters for station 101, G.711u to 10.5.11.32 port 1234, incoming audio to AlphaCom on port 4322. | |||
| $VAC configure the RTP audio stream for "RTP-stream station", to activate the audio the station must be called or controlled by $CONN etc. Note that RTP uses even port numbers, and RTCP uses odd port numbers. So it must be at least 2 between source and destination port. E.g. 2000, 2002 etc. Often used together with IP Dummy Station. | ||||
| 1 | NET_OBJ_REF | Source AlphaCom station | ||
| 2 | UINT1 | Codec type AlphaCom level codecs OBSOLETE, VALUE 1,2 and 3 SHOULD NOT BE USED 1. G.711u 2. G.711a 3. G722 Telecom level codecs (+9dB louder than AlphaCom level) 6. G.711u 7. G.711a 8. G.722 | ||
| 3 | TEXT16 | Destination IP address | ||
| 4 | UINT2 | Destination IP port | ||
| 5 | UINT2 (optional) |
Port in AlphaCom for receiving audio from external source. (If port not specified streaming to AlphaCom is not possible) | ||
| 6 | UINT1 (optional) |
MultiCast Ethernet port 0 or 1. If the AlphaCom system is set up for MultiCast this parameter specify the physical eth where the MulitCast rtp group and program conference should be transmitted. Default is unicast (value 2). | ||
By default the RTP stream station is "REGISTERED" during system start up. If manual registration is needed the system flag "RTP_stream_man_reg" can be used. If set the RTP stream station is down until the first "$VAC" command is received.
&000204 .ex_profile.flags.RTP_stream_man_reg = 0 (0x00000000)
|
Group Call and Program Conference
When the RTP-stream station is included in a group call or program conference the RTP stream is sent to the destination IP address as specified in param 3 of $VAC. The IP port used is the port specified for IP station Group Call and Program Conference.
ex_profile.ip_config.ip_st_audio_group = 61002 (0xee4a)
|
ex_profile.ip_config.ip_st_audio_prog = 61004 (0xee4c)
|