Actions

Difference between revisions of "ICX-510 (Zenitel Connect Pro)"

From Zenitel Wiki

(→‎Front view)
(→‎Start up and initial configuration)
 
(30 intermediate revisions by the same user not shown)
Line 7: Line 7:
 
== Description ==
 
== Description ==
 
=== Front view ===
 
=== Front view ===
−
ICX-510 FrontView.PNG
 
  
 +
<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
 +
<tr style="rowspan:2;">
 +
<td style="display: block; vertical-align: bottom;">[[Image:ICX-510 FrontView.PNG|500px]]</td>
 +
</tr>
 +
<tr>
 +
<td style='background-color:#efefef;'>ICX-510 Front view</td>
 +
</tr>
 +
</table>
 +
<br>
  
 
{| border="1" {{table}}}
 
{| border="1" {{table}}}
Line 15: Line 23:
 
| align="center" style="background:#ffd400;"|'''Comment'''
 
| align="center" style="background:#ffd400;"|'''Comment'''
 
|-
 
|-
−
| 1 ||Power LED||Steady green when power is applied to the ICX-510
+
|1||Power LED||Steady green when power is applied to the ICX-510
 
|-
 
|-
−
| Status LED||Flashing green when the ICX is running
+
|2||Status LED||Flashing green when the ICX-510 is running
 
|-
 
|-
−
| Fault LED||Steady amber when the system reports an error. The LED will be lit during application or system reset, or if there is a temperature alarm.
+
|3||Fault LED||Steady amber when the system reports an error. The LED will be lit during application or system reset, or if there is a temperature alarm.
 
|-
 
|-
−
| Active LED||Steady blue when the ICX-510 is operational
+
|4||Active LED||-
 
|-
 
|-
−
| Link LED||Steady green when the ethernet link 0 or 1 is up. There is one LED for each ethernet port
+
|5||Link LED||Steady green when the ethernet link 0 or 1 is up. There is one LED for each ethernet port
 
|-
 
|-
−
| RX/TX LED||Flashing when receiving or transmitting data on ethernet port 0 or 1.
+
|6||RX/TX LED||Flashing when receiving or transmitting data on ethernet port 0 or 1.
 
|-
 
|-
−
| Securing hole||2 x screw holes, diagonally placed, for M4 screws. Used for rack mounting
+
|7||Securing hole||2 x screw holes, diagonally placed, for M4 screws. Used for rack mounting
 
|-
 
|-
 
|}
 
|}
 +
 +
<br>
  
 
=== Rear view ===
 
=== Rear view ===
−
ICX-510 RearView.PNG
+
<table style="max-width:80%; border-style: double; border-color: #c7c7c7;">
 +
<tr style="rowspan:2;">
 +
<td style="display: block; vertical-align: bottom;">[[Image:ICX-510 RearView.PNG|600px]]</td>
 +
</tr>
 +
<tr>
 +
<td style='background-color:#efefef;'>ICX-510 Rear view</td>
 +
</tr>
 +
</table>
 +
 
 +
 
  
−
==Connectors and indicators==
 
−
=== Overview ===
 
 
{| border="1" {{table}}}
 
{| border="1" {{table}}}
−
| align="center" style="background:#ffd400;"|'''Connector'''
+
| align="center" style="background:#ffd400;"|'''Item'''
 +
| align="center" style="background:#ffd400;"|'''Description'''
 
| align="center" style="background:#ffd400;"|'''Type'''
 
| align="center" style="background:#ffd400;"|'''Type'''
−
| align="center" style="background:#ffd400;"|'''Description'''
+
| align="center" style="background:#ffd400;"|'''Comment'''
 
|-
 
|-
−
| Ethernet||Eth0/Eth1||Two 1Gbps ethernet interfaces.  Each Ethernet port is equipped with LED indicators for link and activity.
+
|1|| Status LED||-||Indicates the same as the LED lights on the front of the box.
 
|-
 
|-
−
| Power||24-48VDC||ICX-510 is powered from a DC power supply with nominal voltage 24VDC or 48VDC (Min/Max: 20VDC-63VDC)
+
|2|| Ethernet port||Eth0/Eth1||Two 1Gbps ethernet interfaces.  Each Ethernet port is equipped with LED indicators for link and activity.
 
|-
 
|-
−
| Console port RS232||RJ45||RS232 port is the RJ45 part of the dual connector RS232/USB. This is a console port for debugging purposes.<br>Com parameters: 115.200 baud, 8 data bits, no parity, 1 stop bit.
+
|3|| Power In||24-48VDC||ICX-510 is powered from a DC power supply with nominal voltage 24VDC or 48VDC (Min/Max: 20VDC-63VDC)
 
|-
 
|-
−
| USB||USB A<br>USB micro-B||ICX-510 features one USB A and one USB micro-B connector
+
|4|| Console port RS232||RJ45||RS232 port is the RJ45 part of the dual connector RS232/USB. This is a console port for debugging purposes.<br>Com parameters: 115.200 baud, 8 data bits, no parity, 1 stop bit.
 
|-
 
|-
−
| Fault Relay||3 pole terminal block||Fault relay is used to indicate system status together with Fault LED
+
|5|| USB A port||-||-
 
|-
 
|-
−
| SD card||Micro SD card||Used for external storage or system recovery (Behind protection lid)
+
|6|| USB Micro-B||-||-
 
|-
 
|-
−
| Factory Default Button||Tact switch||Used for resetting ICX-510 to factory default settings
+
|7|| Fault Relay||3 pole terminal block||The fault relay will trigger when the system reports an error. In normal operation the relay is energized, which means it will also trigger on power outage. The relay reports fault:
 +
*During Application or System reset
 +
*If there is a Temperature alarm (Threshold is 85 degrees C on the CPU)
 +
*If there is a Power failure
 
|-
 
|-
−
|}
+
|8|| SD card slot||Micro SD card||Used for system recovery (Behind protection lid)
−
 
 
−
 
 
−
[[File:ICX-510 rear.jpg|800px|left|thumb|Rear view of the ICX-510 Gateway.]]
 
−
<br style="clear:both;" />
 
−
 
 
−
===Power===
 
−
The [[IPS-AC1]] from Zenitel is a 48VDC power supply, with input voltage range 85-264 VAC. It is designed for DIN-Rail mounting.
 
−
 
 
−
[[File:PSU IPS-AC1.png|150px|left|thumb|The Power Supply IPS-AC1 (Item no: 1002510000)]]
 
−
<br style="clear:both;" />
 
−
 
 
−
As an option one can use a locally provided power supply unit (PSU). The ICX-510 Gateway must be powered by 24VDC or 48VDC. Recommended power rating of the PSU is minimum 24W (24V/1A or 48V/0.5A).
 
−
 
 
−
{{obs|In order to comply with UL safety requirements, the ICX-510 has to be supplied by a power supply specified as a Limited Power Source (LPS) or PS2 (cased on IEC/UL 62368-1 definition) or NEC Class 2 source of supply. The IPS-AC1 meets this criterion.}}
 
−
 
 
−
<br>
 
−
 
 
−
=== Network ===
 
−
The ICX-510 Gateway has two RJ-45 ethernet ports for IP communication. Ethernet port 0 (Eth 0) is by default configured as a Management port, allowing connection to the embedded web server. See [[Getting_Started_(Zenitel_Connect_Pro)#How_to_Access_the_Zenitel_Connect_Pro_web_interface|How to access the Zenitel Connect Pro web interface]].
 
−
 
 
−
Default IP addresses:
 
−
* Eth0: Static IP address 169.254.1.5
 
−
* Eth1: DHCP
 
−
 
 
−
<br>
 
−
 
 
−
=== Status LEDs ===
 
−
The ICX-510 Gateway has a number of status LEDs. The same LEDs are located both in front and at the rear side of the unit.
 
−
 
 
−
{| border="1" {{table}}}
 
−
| align="center" style="background:#ffd400;"|'''LED'''
 
−
| align="center" style="background:#ffd400;"|'''Description'''
 
−
|-
 
−
| Power||Steady green when power is applied to the ICX-510
 
−
|-
 
−
| Status||Flashing green when the ICX is running
 
−
|-
 
−
| Fault||Steady amber when the system reports an error. The LED will be lit during application or system reset, or if there is a temperature alarm.
 
−
|-
 
−
| Active||Steady blue when the ICX-510 is operational
 
 
|-
 
|-
−
| Link||Steady green when the ethernet link 0 or 1 is up. There is one LED for each ethernet port
+
|9|| Factory Default Button||Tact switch||Used for resetting ICX-510 to factory default settings
−
|-
 
−
| RX/TX||Flashing when receiving or transmitting data on ethernet port 0 or 1.
 
 
|-
 
|-
 
|}
 
|}
−
 
−
<br>
 
−
 
−
=== Fault Relay ===
 
−
The fault relay will trigger when the system reports an error. In normal operation the relay is energized, which means it will also trigger on power outage.
 
−
 
−
The relay reports fault:
 
−
* During Application or System reset
 
−
* If there is a Temperature alarm (Threshold is 85 degrees C on the CPU)
 
−
* If there is a Power failure
 
−
 
 
<br>
 
<br>
  
Line 124: Line 92:
 
# Power up the ICX-510 Gateway
 
# Power up the ICX-510 Gateway
 
# Watch the LEDs. During startup the Power LED and the Fault LED will be lit. The system uses approx. 2 minutes to start up. When up and running, the green status LED will start flashing.
 
# Watch the LEDs. During startup the Power LED and the Fault LED will be lit. The system uses approx. 2 minutes to start up. When up and running, the green status LED will start flashing.
 +
# Connect your laptop to Ethernet port 0 (Eth 0) of the ICX-510 unit. Open a web browser (e.g. Chrome or Firefox), and enter the IP address of the ICX-510 in the address bar. The default IP address is '''169.254.1.5''', with subnet mask '''255.255.0.0'''. Default username and password: '''admin'''/'''admin'''. Make sure your laptop is in the 169.254.x.x range.
 
# For further details, see the [[Getting Started (Zenitel Connect Pro)]] article.
 
# For further details, see the [[Getting Started (Zenitel Connect Pro)]] article.
  
−
 
+
<br>
−
=== Station & Device configuration===
 
−
To add stations and devices to the ICX-510 see [[Getting_Started_(Zenitel_Connect_Pro)#Adding_Stations_and_Devices|Adding Stations and Devices]]
 
−
 
 
−
=== Network requirements ===
 
−
In order to configure the intercoms and have audio and video communication between intercoms, the appropriate ports must be open in the [[Firewall (Zenitel Connect Pro)|firewall]]. Necessary ports are open by default.
 
  
 
==Factory Reset ==
 
==Factory Reset ==
Line 163: Line 127:
 
<li> Keep the button pressed for approx. 5 sec., then release it</li>
 
<li> Keep the button pressed for approx. 5 sec., then release it</li>
 
<li> Once the ICX-510 is up and running again, connect a PC with a browser to Eth0. Navigate to '''169.254.1.5:82'''.<br>
 
<li> Once the ICX-510 is up and running again, connect a PC with a browser to Eth0. Navigate to '''169.254.1.5:82'''.<br>
−
[[File:ZCP_SoftwareRecovery.png|thumb|left|700px|Software Upgrade window]]
+
[[File:ZCP_SoftwareRecovery.png|thumb|left|600px|Software Upgrade window]]
 
<br style="clear:both;" /></li>
 
<br style="clear:both;" /></li>
 
<li> Drag and drop or upload the software update image (.swu).</li>
 
<li> Drag and drop or upload the software update image (.swu).</li>

Latest revision as of 14:25, 23 October 2024

ZCP IconPlatf.PNG
The ICX-510 Gateway (Item no: 1002000200)

The ICX-510 Gateway is the latest generation Intelligent Communications Platform from Zenitel. This article gives a general description of the hardware, and how to get started with the configuration of the system.


Description

Front view

ICX-510 FrontView.PNG
ICX-510 Front view


Item Description Comment
1 Power LED Steady green when power is applied to the ICX-510
2 Status LED Flashing green when the ICX-510 is running
3 Fault LED Steady amber when the system reports an error. The LED will be lit during application or system reset, or if there is a temperature alarm.
4 Active LED -
5 Link LED Steady green when the ethernet link 0 or 1 is up. There is one LED for each ethernet port
6 RX/TX LED Flashing when receiving or transmitting data on ethernet port 0 or 1.
7 Securing hole 2 x screw holes, diagonally placed, for M4 screws. Used for rack mounting


Rear view

ICX-510 RearView.PNG
ICX-510 Rear view


Item Description Type Comment
1 Status LED - Indicates the same as the LED lights on the front of the box.
2 Ethernet port Eth0/Eth1 Two 1Gbps ethernet interfaces. Each Ethernet port is equipped with LED indicators for link and activity.
3 Power In 24-48VDC ICX-510 is powered from a DC power supply with nominal voltage 24VDC or 48VDC (Min/Max: 20VDC-63VDC)
4 Console port RS232 RJ45 RS232 port is the RJ45 part of the dual connector RS232/USB. This is a console port for debugging purposes.
Com parameters: 115.200 baud, 8 data bits, no parity, 1 stop bit.
5 USB A port - -
6 USB Micro-B - -
7 Fault Relay 3 pole terminal block The fault relay will trigger when the system reports an error. In normal operation the relay is energized, which means it will also trigger on power outage. The relay reports fault:
  • During Application or System reset
  • If there is a Temperature alarm (Threshold is 85 degrees C on the CPU)
  • If there is a Power failure
8 SD card slot Micro SD card Used for system recovery (Behind protection lid)
9 Factory Default Button Tact switch Used for resetting ICX-510 to factory default settings


Mounting and Installation

Please see the ICX-510 Mounting & Installation Manual


Start up and initial configuration

Starting up the ICX-510
  1. Power up the ICX-510 Gateway
  2. Watch the LEDs. During startup the Power LED and the Fault LED will be lit. The system uses approx. 2 minutes to start up. When up and running, the green status LED will start flashing.
  3. Connect your laptop to Ethernet port 0 (Eth 0) of the ICX-510 unit. Open a web browser (e.g. Chrome or Firefox), and enter the IP address of the ICX-510 in the address bar. The default IP address is 169.254.1.5, with subnet mask 255.255.0.0. Default username and password: admin/admin. Make sure your laptop is in the 169.254.x.x range.
  4. For further details, see the Getting Started (Zenitel Connect Pro) article.


Factory Reset

In case there is a need to restore factory settings, there are two options:

  • Factory reset from the web interface
  • Hardware reset by using the reset button on the rear side of the unit

From the web interface

Factory reset can be done from the Zenitel Connect Pro web interface. For details see Backup and Recovery (Zenitel Connect Pro).

Using the Reset button

The reset button is available through a small hole at the rear side of the ICX-510.

Warning icon Hardware reset will remove the configuration, as well as all running containers; Once the ICX-510 has restarted it is necessary to do a software upgrade procedure to load the application software


If proceeding, this will:

  • remove the database
  • remove licenses
  • remove the backup file - always store backup file and license file in a safe location
  • reset all IP settings to default (E.g. IP addresses and Firewall). Eth0 will get IP address 169.254.1.5, subnet mask 255.255.0.0.
  • remove all containers (in effect all application software)

If you get a login window like this, the ICX is in recovery mode and you need to upgrade by using port 82. See the procedure below.

ZCP Recovery mode


Procedure to recover the ICX-510:

  1. Press and hold the "Factory Default" button
  2. Power up the ICX-510 while the button is pressed
  3. Keep the button pressed for approx. 5 sec., then release it
  4. Once the ICX-510 is up and running again, connect a PC with a browser to Eth0. Navigate to 169.254.1.5:82.
    Software Upgrade window

  5. Drag and drop or upload the software update image (.swu).
  6. Wait for the update to complete, the device will restart. See the Getting Started (Zenitel Connect Pro) article on how to configure the unit.


Additional information

Retrieved from "https://wiki.zenitel.com/w/index.php?title=ICX-510_(Zenitel_Connect_Pro)&oldid=238086"