Actions

Difference between revisions of "IP Flush Master DAK-48 Module"

From Zenitel Wiki

(Installation)
Line 16: Line 16:
  
 
==Installation==
 
==Installation==
See article: [[CRM_V_-_Control_Room_Master#DAK-48_Expansion_module|CRM - DAK48 Installation]]
+
===DAK-48 Expansion module===
 +
The IP DAK-48 unit expands the IP Flush Master station with an additional 48 Direct Access Keys. Up to two DAK-48 units can be connected to one station.
  
 +
To interconnect the DAK-48 unit to the main unit, use the cable which is coming with the DAK-48 unit. The DAK-48 unit receive its power and data via this cable.
  
 +
'''WARNING:''' A standard patch cable (1:1) must not be used. It might damage the unit!
  
 +
Installing the IP DAK-48 Unit:
 +
* Power off the IP Flush Master station by disconnecting the ethernet cable in the LAN port
 +
* Plug one end of the cable coming with the DAK-48 unit into the RJ45 port on the right hand side of the IP Flush Master station (when the station is viewed from the front).
 +
* Plug the other end of the cable into the left RJ45 port on the DAK-48 unit (when the unit is viewed from the front).
 +
* Power up the IP Flush Master station by connecting the ethernet cable to the LAN port
  
The IP DAK-48 unit expands the IP Flush Master station with an additional 48 Direct Access Keys. This unit can also be used with the IP OR Station and the IP Master Station Kit.
+
[[File:IP_Master_DAK-48_Unit_Installation.PNG]]
  
Before installation, disconnect power from the IP Flush Master station
 
 
The accompanying RJ45-RJ45 cable is used to install the DAK unit on an IP Flush Master station. This cable has an RJ45 plug at both ends. The two ends are interchangeable. Up to two DAK units can be installed per station. Each DAK unit has two RJ45 ports, one located on the left side and one on the right side.
 
 
<u>'''To install the IP DAK-48 Unit:'''</u><br/>
 
* Plug one end of the RJ45-RJ45 cable into the RJ45 port on the right of the station (when the station is viewed from the front).
 
* Plug the other end of the RJ45-RJ45 cable into the left (when the unit is viewed from the front) RJ45 port on the DAK unit.
 
 
[[File:IP_Master_DAK-48_Unit_Installation.PNG]]<br/>
 
 
Installing the IP DAK-48 Unit
 
Installing the IP DAK-48 Unit
 
  To add another DAK unit, plug one end of an RJ45-RJ45 cable into the RJ45 port of  
 
  To add another DAK unit, plug one end of an RJ45-RJ45 cable into the RJ45 port of  

Revision as of 12:49, 24 October 2016

DAK-48 Unit
Note! The license 1009648001 is required to extend the IP Flush Master with the optional IP DAK-48 Unit.

Highlights

  • Extends IP Flush Master Station with 48 programmable DAK keys (direct access keys)
  • Ideal for control room applications
  • Visual indications with two LEDs (green/red) per DAK key
  • All keys have backlight (adjustable)
  • Easy labeling of keys

Software requirements

  • IP Flush Master: Version 01.09.3.0 or later
  • AMC-IP: Version 10.60.3.0 or later

Installation

DAK-48 Expansion module

The IP DAK-48 unit expands the IP Flush Master station with an additional 48 Direct Access Keys. Up to two DAK-48 units can be connected to one station.

To interconnect the DAK-48 unit to the main unit, use the cable which is coming with the DAK-48 unit. The DAK-48 unit receive its power and data via this cable.

WARNING: A standard patch cable (1:1) must not be used. It might damage the unit!

Installing the IP DAK-48 Unit:

  • Power off the IP Flush Master station by disconnecting the ethernet cable in the LAN port
  • Plug one end of the cable coming with the DAK-48 unit into the RJ45 port on the right hand side of the IP Flush Master station (when the station is viewed from the front).
  • Plug the other end of the cable into the left RJ45 port on the DAK-48 unit (when the unit is viewed from the front).
  • Power up the IP Flush Master station by connecting the ethernet cable to the LAN port

IP Master DAK-48 Unit Installation.PNG

Installing the IP DAK-48 Unit

To add another DAK unit, plug one end of an RJ45-RJ45 cable into the RJ45 port of 
the installed unit and plug the other end into the RJ45 port of the new unit.


Additional Documentation on Zenitel.com

Related article

Related products

  • Label Paper for IP DAK-48 Unit - 1008010101 (20 sheets)