Difference between revisions of "INCA IP DualDisplay Station - Restore Factory Defaults"
From Zenitel Wiki
(→Load factory defaults via the display menu) |
(→Load factory defaults via power boot sequence) |
||
Line 22: | Line 22: | ||
== Load factory defaults via power boot sequence == | == Load factory defaults via power boot sequence == | ||
+ | |||
+ | The unit can be set to use either '''Static IP''' or '''DHCP'''. On the rear side of the PCB there is a red status LED. Pay attention to this LED during the restore procedure: | ||
+ | |||
+ | [[File:Load Defaults without KEY.PNG|right|thumb|800px|Connect a push button between pins 1 and 4]] | ||
+ | |||
+ | # Connect a push button ('''KEY1''') between pin 1 and 4 on the P4 connector. | ||
+ | # While pressing the button, power up the station kit and keep the button pressed. | ||
+ | # Release the button '''after exactly 2 flashes''' of the LED. | ||
+ | # Let the LED flash for '''exactly 2 more times''' (Static IP) or '''exactly 4 more times''' (DHCP), then press the button again. | ||
+ | # Keep the button pressed until the LED '''flashes fast 2 times''' (Static IP) or '''flashes fast 4 times''' (DHCP) indicating a successful reset. | ||
+ | # Release the button and the station will restart with the factory default settings. | ||
+ | |||
+ | |||
+ | |||
+ | Factory default values: | ||
+ | *Station Mode: '''Pulse''' | ||
+ | *Station IP address: '''169.254.1.100''' or '''DHCP''' | ||
+ | *Username: '''admin''' | ||
+ | *Password: '''alphaadmin''' | ||
+ | |||
+ | ----------------- | ||
+ | |||
+ | |||
The Factory Default procedure can be used to either set the station to use a Static IP address, or to use IP address from a DHCP server. | The Factory Default procedure can be used to either set the station to use a Static IP address, or to use IP address from a DHCP server. | ||
Revision as of 14:34, 17 March 2017
The IP DualDisplay station can be reset to Factory Default settings in two ways:
- From the display menu
- By a power boot sequence
Contents
The Station Menu is available when the IP Station is in offline mode. i.e. not registered to the server.
- Press the Setup button beneath the display
- Enter the password 1851 and press the Ok button.
- Navigate to Load defaults and press the Sel button.
- Press the Sel button to load factory defaults.
The station will now restart with factory settings:
- Station Mode: Pulse
- Station IP address: 169.254.1.100
- Username: admin
- Password: alphaadmin
Load factory defaults via power boot sequence
The unit can be set to use either Static IP or DHCP. On the rear side of the PCB there is a red status LED. Pay attention to this LED during the restore procedure:
- Connect a push button (KEY1) between pin 1 and 4 on the P4 connector.
- While pressing the button, power up the station kit and keep the button pressed.
- Release the button after exactly 2 flashes of the LED.
- Let the LED flash for exactly 2 more times (Static IP) or exactly 4 more times (DHCP), then press the button again.
- Keep the button pressed until the LED flashes fast 2 times (Static IP) or flashes fast 4 times (DHCP) indicating a successful reset.
- Release the button and the station will restart with the factory default settings.
Factory default values:
- Station Mode: Pulse
- Station IP address: 169.254.1.100 or DHCP
- Username: admin
- Password: alphaadmin
The Factory Default procedure can be used to either set the station to use a Static IP address, or to use IP address from a DHCP server.
Restore with Static IP
- Press and hold the Privacy button. Power up the station
- When the station LED starts blinking, release the privacy button after exactly 2 blinks.
- Let the LED blink for exactly 2 more times, then press the button again.
- Keep the button pressed until the LED blinks fast 2 times indicating a successful reset with static IP.
- Release the button and the station will restart with the factory default settings.
Factory default values:
- Station Mode: Pulse
- Station IP address: 169.254.1.100
- Username: admin
- Password: alphaadmin
Restore with DHCP enabled
- Press and hold the Privacy button. Power up the station
- When the station LED starts blinking, release the privacy button after exactly 2 blinks.
- Let the LED blink for exactly 4 more times, then press the button again.
- Keep the button pressed until the LED blinks fast 4 times indicating a successful reset with DHCP.
- Release the button and the station will restart with the factory default settings.
Factory default values:
- Station Mode: Pulse
- Station IP address: From DHCP server
- Username: admin
- Password: alphaadmin