Difference between revisions of "Turbine Extended Board Connectors"
From Zenitel Wiki
(→J8: Headset/Handset connector) |
(→J8: Headset/Handset connector) |
||
| Line 59: | Line 59: | ||
=== J8: Headset/Handset connector === | === J8: Headset/Handset connector === | ||
| − | *Pin 1 Offhook | + | *Pin 1: Offhook |
| − | *Pin 2 GND | + | *Pin 2: GND |
| − | *Pin 3 PTT | + | *Pin 3: PTT |
| − | *Pin 4 Handset Mic Positive | + | *Pin 4: Handset Mic Positive |
| − | *Pin 5 Handset Mic Negative | + | *Pin 5: Handset Mic Negative |
| − | *Pin 6 Headphone Positive | + | *Pin 6: Headphone Positive |
| − | *Pin 7 Headphone Negative | + | *Pin 7: Headphone Negative |
| − | *Pin 8 Line In Positive | + | *Pin 8: Line In Positive |
| − | *Pin 9 Line In Negative | + | *Pin 9; Line In Negative |
| − | * Headset speaker | + | * Headset/handset speaker (pin 6/7): Minimum 32 Ohms |
| − | * Microphone input | + | * Microphone input (pin 4/5): For electret type. Bias voltage is 1,25V. |
=== J9: Keyboard connector === | === J9: Keyboard connector === | ||
Revision as of 10:16, 2 January 2019
Contents
- 1 PCB - Front
- 1.1 P1 & P2: RJ45 PoE port for 10/100 Mbit Ethernet connection
- 1.2 P3: Secondary Power; 24-48VDC
- 1.3 P4: 10-pin plug-on terminal for external connections
- 1.4 P5: 6-pin plug-on terminal for external connections
- 1.5 P6: Loudspeaker & Electret microphone
- 1.6 J2: Turbine Relay Module - TA-10
- 1.7 J8: Headset/Handset connector
- 1.8 J9: Keyboard connector
PCB - Front
P1 & P2: RJ45 PoE port for 10/100 Mbit Ethernet connection
- The station can be powered from this port if the line supports Power over Ethernet (PoE).
P3: Secondary Power; 24-48VDC
P4: 10-pin plug-on terminal for external connections
- Pin 1 5.3V
- Pin 2 GND
- Pin 3 Button Input or LED Driver
- Pin 4 Button Input or LED Driver
- Pin 5 Button Input or LED Driver
- Pin 6 Button Input or LED Driver
- Pin 7 Button Input or LED Driver
- Pin 8 Button Input or LED Driver
- Pin 9 600 ohm balanced line out +
- Pin 10 600 ohm balanced line out -
- Output ratings: 12mA as LED drivers
- Connectable conductors: 0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm².
P5: 6-pin plug-on terminal for external connections
- Pin 1 COM relay 1 (Common)
- Pin 2 NO relay 1 (Normal Open)
- Pin 3 NC relay 1 (Normal Closed)
- Pin 4 COM relay 2(Common)
- Pin 5 NO relay 2 (Normal Open)
- Pin 6 NC relay 2 (Normal Closed)
- Relay switching capacity: Max. 60 watt (Max voltage: 250VAC/220VDC. Max current: 2A)
- Connectable conductors: 0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm².
P6: Loudspeaker & Electret microphone
- Pin 1 10W Speaker amplifier +
- Pin 2 10W Speaker amplifier -
- Pin 3 Electret Microphone +
- Pin 4 Electret Microphone -
- Connectable conductors: 0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm².
J2: Turbine Relay Module - TA-10
For details, see Turbine Relay Module - TA-10
J8: Headset/Handset connector
- Pin 1: Offhook
- Pin 2: GND
- Pin 3: PTT
- Pin 4: Handset Mic Positive
- Pin 5: Handset Mic Negative
- Pin 6: Headphone Positive
- Pin 7: Headphone Negative
- Pin 8: Line In Positive
- Pin 9; Line In Negative
- Headset/handset speaker (pin 6/7): Minimum 32 Ohms
- Microphone input (pin 4/5): For electret type. Bias voltage is 1,25V.
J9: Keyboard connector
Only available on TKIE-3. See keyboard matrix article for details.