Revision as of 13:38, 3 October 2024

Previous Release - VSF-Fortitude8 8.2 Release Notes

This document provides the release notes for VSF-Fortitude8 9.0 with incremental bug fix releases. The release notes for VSF-Fortitude8 9.0 describe new features, improvements and issues fixed after VSF-Fortitude8 8.2.3.3.

Release info

Name: VSF-Fortitude8
Description: VSF-Fortitude8 is a firmware for Zenitel devices based on the IMX8 processor.

The firmware is delivered in two different files:

vsff8-9.0.3.x - Used for standard in-field upgrades
vsff8-prod-9.0.3.x - Used in production- and recovery upgrades.

Version: 9.0.3.0
Date: 03.10.24
Status: General Availability

VSF-FORTITUDE8 9.0.3.0

Improvements

MTN-4397 Improved certificate handling, and split SIP and HTTPS certificates into separate pages

Split SIP and HTTPS certificates into separate pages, removed turbine_server_sha1.key private key and TLS Private Key option, added factory reset handling, added backup and recovery for SIP certificates, fixed certificate regeneration on some devices, removed private keys from the device web page.

MTN-3557 New configuration option for RTSP Audio Source

There’s a new option for configuring RTSP Audio Source, “Mixed signal”. This option mixes far and near end signal.

DS-1034 Added support for codec L16x48 to Multicast Paging config

Devices can now listen to raw PCM 48 kHz audio stream (L16x48) when configured in HD-Audio mode.

DS-970 Added multicast relay feature

Device can now relay incoming RTP to specified address and port.

DS-889 Operate output when the call button is pressed in idle

Added option to configure operation of relays and outputs when the call button is pressed.

Issues fixed

MTN-4563 Changing zoom setting caused video to stop working and device reboot

When user changed video zoom setting from default one and rebooted device would get into reboot loop with video not working. Factory reset would had resolved it. This is now fixed.

MTN-4438 The 0,5 video zoom level is now available again

The 0,5 video zoom level was missing in the device web in version 8.2. It is now available again.

MTN-4383 Added Missing SNMP traps on TCIV+

Fixed missing “Input Button Pressed/Released“ option in Advanced Network on TCIV+ devices.

MTN-4373 Fixed a typo in I/O settings

Changed label from “Ouput“ to “Output” in I/O settings page for I/O pins.

DS-1015 Permanent Audio Stream fixes and config refresh

Some parts of the audio stream config was not working correct and mic level was very low. Also linked to RTSP “Audio Source” config for impact which signal is sent to RTP stream. Consult wiki documentation for more details.

Known Issues

MTN-4121 Known issue: Asterisk discards alternative profiles

Default setting for ITSV-5 sends 3 types (BP & MP & HP). However, Asterisk discards all but the first profile it receives (HP in this case). Since only the "Baseline profile" is supported on the device the video doesn't load. A workaround to this issue is to select "Baseline profile" as the H.264 profile type on the ITSV-5.

The issue has been reported and documented here: https://issues.asterisk.org/jira/browse/ASTERISK-29182

@@ Line 36: / Line 36: @@
 ==Issues fixed==
-===MTN-4229 HD audio for back ground music distribution in ICX-AlphaCom produced noise===
+=== MTN-4563 Changing zoom setting caused video to stop working and device reboot===
-Issue with PCM sampling is now fixed.
+When user changed video zoom setting from default one and rebooted device would get into reboot loop with video not working. Factory reset would had resolved it. This is now fixed.
-=== MTN-4206 SIP H.264 video calls are now working properly with Genetec Sipelia and Cisco===
+=== MTN-4438 The 0,5 video zoom level is now available again===
-There was an issue with SIP H.264 video calls with Genetec Sipelia and Cisco, this is now fixed.
+The 0,5 video zoom level was missing in the device web in version 8.2. It is now available again.
-=== MTN-4181 Report DAK and Report station call events as Digital Input in ONVIF options are now working for Hanwha VMS===
+=== MTN-4383 Added Missing SNMP traps on TCIV+===
-There was an issue with how Report DAK and Report station call events as Digital Input in ONVIF options were behaving in Hanwha VMS, this is now fixed and they work as expected.
+Fixed missing “Input Button Pressed/Released“ option in Advanced Network on TCIV+ devices.
-=== MTN-4176 AVC config now shown under Audio Settings===
+=== MTN-4373 Fixed a typo in I/O settings===
-AVC config was missing on 7.5 version. This is fixed, AVC is now visible and configurable.
+Changed label from “Ouput“ to “Output” in I/O settings page for I/O pins.
-=== MTN-4072 JQuery version update to version 3.6.4===
+=== DS-1015 Permanent Audio Stream fixes and config refresh===
-Now the Station Web is running newer JQuery version with included JQuery migrate to support some of the older functions.
+Some parts of the audio stream config was not working correct and mic level was very low. Also linked to RTSP “Audio Source” config for impact which signal is sent to RTP stream.
+Consult wiki documentation for more details.
 <br>

Difference between revisions of "VSF-Fortitude8 9.0 Release Notes"

From Zenitel Wiki