Difference between revisions of "SET CALL REQ MODE"
From Zenitel Wiki
m (Text replacement - "<br\>" to "<br />") |
|||
| Line 8: | Line 8: | ||
|colspan="5"|'''$SCRM L101 L102 U0 U1''' | |colspan="5"|'''$SCRM L101 L102 U0 U1''' | ||
|- | |- | ||
| − | |colspan="5"|Turn on/off message "your call is registered, please wait", then ring/flashing at a station. Note that the station leaves this mode if becomes busy for some reason (dialing, incoming conv.)<br | + | |colspan="5"|Turn on/off message "your call is registered, please wait", then ring/flashing at a station. Note that the station leaves this mode if becomes busy for some reason (dialing, incoming conv.)<br />"Call requester mode" is normally used to inform the user about a successful activation of call request. |
|- | |- | ||
| − | |align=center|1||[[NET_OBJ_REF]]<br | + | |align=center|1||[[NET_OBJ_REF]]<br />{[[ECL_STATION]]}||colspan="3"|Station |
|- | |- | ||
| − | |align=center|2||[[NET_OBJ_REF]]<br | + | |align=center|2||[[NET_OBJ_REF]]<br />{[[ECL_STATION]]}||colspan="3"|Station that received the call request mail (i.e. sender of this command) |
|- | |- | ||
|align=center|3||[[UINT1]]||colspan="3"|UserDefined Properties ([[UDP]]) of the station that received the call request mail. | |align=center|3||[[UINT1]]||colspan="3"|UserDefined Properties ([[UDP]]) of the station that received the call request mail. | ||
|- | |- | ||
| − | |align=center|4||[[UINT1]]||colspan="3"|New call requester mode:<br | + | |align=center|4||[[UINT1]]||colspan="3"|New call requester mode:<br /> 0 = off<br />1 = on |
|- | |- | ||
| − | |align=center|5||[[UINT1]]<br | + | |align=center|5||[[UINT1]]<br />||colspan="3"|Mail Priority 0 - 255<br /> |
|- | |- | ||
| − | |align=center|6||[[UINT1]]<br | + | |align=center|6||[[UINT1]]<br />||colspan="2"|Mail Flags: [[SEND_MAIL | SEND_MAIL]] |
|- | |- | ||
|colspan="2"|Response:||colspan="3"|[[COMMAND_RESPONSE]] | |colspan="2"|Response:||colspan="3"|[[COMMAND_RESPONSE]] | ||
Revision as of 10:46, 8 March 2016
| SET_CALL_REQ_MODE | 0x006C | 108 | AMC 07.00 | |
|---|---|---|---|---|
| $SCRM L101 L102 U0 U1 | ||||
| Turn on/off message "your call is registered, please wait", then ring/flashing at a station. Note that the station leaves this mode if becomes busy for some reason (dialing, incoming conv.) "Call requester mode" is normally used to inform the user about a successful activation of call request. | ||||
| 1 | NET_OBJ_REF {ECL_STATION} |
Station | ||
| 2 | NET_OBJ_REF {ECL_STATION} |
Station that received the call request mail (i.e. sender of this command) | ||
| 3 | UINT1 | UserDefined Properties (UDP) of the station that received the call request mail. | ||
| 4 | UINT1 | New call requester mode: 0 = off 1 = on | ||
| 5 | UINT1 |
Mail Priority 0 - 255 | ||
| 6 | UINT1 |
Mail Flags: SEND_MAIL | ||
| Response: | COMMAND_RESPONSE | |||