Difference between revisions of "Dynamic group call"
From Zenitel Wiki
(New page: ==Operation (CRM IV)== *Press the "Group Config." button, red led in key starts flashing *Select subscribers to be included / excluded (toggle function), flashing green led in key indicate...) |
(→Programming) |
||
| Line 14: | Line 14: | ||
*If not already existing, create 9535 = feature 95/0. The "Group Config." DAK button is programmed to 9535. | *If not already existing, create 9535 = feature 95/0. The "Group Config." DAK button is programmed to 9535. | ||
| − | Each CRMIV must “own” a group call that nobody else uses. The directory number of the group call should be changed so that the two last digits are identical to the group index number. | + | *Each CRMIV must “own” a group call that nobody else uses. The directory number of the group call should be changed so that the two last digits are identical to the group index number. |
Example: | Example: | ||
| − | *Group '''2''' = 85'''02''' | + | **Group '''2''' = 85'''02''' |
| − | *Group '''10''' = 85'''10''' | + | **Group '''10''' = 85'''10''' |
Etc. | Etc. | ||
Revision as of 16:19, 7 December 2007
Operation (CRM IV)
- Press the "Group Config." button, red led in key starts flashing
- Select subscribers to be included / excluded (toggle function), flashing green led in key indicate included
- Press the "Group Config." button again, the group call is activated, red led in key stops flashing
- The green leds continue to flash during the group call
- When the group call is cancelled the group is emptied, and the green leds stop flashing
LIMITATION: You can only include subscribers, you cannot include groups!
Programming
- Software requirement: AMC 8.26 is later
- If not already existing, create 9535 = feature 95/0. The "Group Config." DAK button is programmed to 9535.
- Each CRMIV must “own” a group call that nobody else uses. The directory number of the group call should be changed so that the two last digits are identical to the group index number.
Example:
- Group 2 = 8502
- Group 10 = 8510
Etc.
- Enter the group call directory number associated to the CRMIV in the External Parameter (%1.EXP) field of the CRM IV.
- Put all CRM IV’s that should have Dynamic Group Call feature in UDP group 1.
Event Handler programming:
Owner: Stations w/UDP 1 (CRM IV stations) Event type: 15 – Event Trigger Subtype: 0 When Change to: ON or OFF When Related to: Directory number 0 | 9535 Action: IND %1.phy %1.dak(I%2.dir) 1 3
Owner: Stations w/UDP 1 (CRM IV stations)
Event type: 25 – Event Trigger w/User parameter
Subtype: 0
When Change to: ON or OFF
When Related to: All
Action: IF %sgm(%2.phy,%1.exp(2))
IND %1.phy %1.dak(I%2.dir) 2 3 OFF
ENDIF
IF %op(%sgm(%2.phy,%1.exp(2)),=,0)
IND %1.phy %1.dak(I%2.dir) 2 3 ON
ENDIF
$GRM L%2.dir NG%1.exp(2) U2
IF %op(%2.dir,=,9535)
$DISCON_ST L%1.dir 0
IND %1.phy %1.dak(I%2.dir) 2 3 OFF
pause
pause
pause
$DD L%1.dir L%1.exp
ENDIF
Owner: Stations w/UDP 1 (CRM IV stations) Event type: 08 – Conversation Outgoing When Change to: OFF When Related to: All Action: IF %op(%2.dir,=,%1.exp) IF %gns(%1.exp(2),0) $ER U15 U1 U1 U1 N%gns(%1.exp(2),0) U3 %1.ref ENDIF ENDIF
Owner: Stations w/UDP 8 (All stations)
Event type: 15 – Event Trigger
Subtype: 1 (NOTE: Subtype 1, NOT 0)
When Change to: ON
When Related to: All
Action: $GRM N%gns(%2.exp(2),0) NG %2.exp(2) U0
IND %2.phy %2.dak(I%1.dir) 2 3 OFF
pause
IF %gns(%2.exp(2),0)
$ER U15 U1 U1 U1 N%gns(%2.exp(2),0) U3 %2.ref
ENDIF