STATUS REPORT
From Zenitel Wiki
| STATUS_REPORT | 0x0072 | 114 | AMC 07.30 | |
|---|---|---|---|---|
| Report equipment Presence and Error/OK status for Subscriber Lines, Audio Links, Devices, Boards, etc. Intended for remote logging and external monitoring systems.
As the message is very general, the message definition will be followed by a detailed example of how the different parameters are used for each “entity” type. Unused parameters/flags are always set to 0. | ||||
| 1 | NET_OBJ_REF<br\> {ECL_STATION,<br\> ECL_AUDIO_RING,<br\> ECL_AUDIO_LINK,<br\> ECL_BOARD,<br\> ECL_DEVICE,<br\> ECL_NODE} | Entity Reference to the Station / InterExchange Link / ICC Audio Ring / Board / Device / Exchange the status message is for.<br\>The entity number is a logical number, e.g. station from 1 to 552. | ||
| 2 | NET_OBJ_REF<br\> {NRF_PHYS_ADDR} | Physical address for the entity defined in parameter 1.<br\>This is a hardware module/board/port type of information. | ||
| 3 | BITMAP[1..8] | (Error) State Flags.<br\>Bit 1 = Interface present:<br\>Bit 2 = Interface test:<br\>Bit 4 = Signaling test: Bit 6 = Audio test:<br\>Bit 7 = Device dependent test |
<br\>Board present in exchange<br\>Board reports entity missing/down<br\>Last signaling test failed<br\>Last audio (tone) test failed<br\> | |
| 4 | BITMAP[1..8] | (State) Change Flags.<br\>Each bit is set if the corresponding state flag bit was changed from the previous report and cleared if it was unchanged. | ||
| 5 | BITMAP[1..8] | Reporting Flags.<br\>Bit 8 = VERBOSE. The report is from a manually/externally started test, where the user wants a complete report. | ||
| 6 | UINT1 | Extra (Error) Status Information 1. | ||
| 7 | UINT1 | Extra (Error) Status Information 2. | ||
| 8 | NET_OBJ_REF<br\>(optional) | Entity Information field 1.<br\>. | ||
| STATUS_REPORT for Stations: | ||||
| 1 | NET_OBJ_REF | Station from 1 to 552.<br\>The Sub Class field specifies the type of station interface (TouchLine, Telephone).<br\>Status info. can have different meaning for each Sub Class. | ||
| 2 | NET_OBJ_REF | Physical address: Module/board/port.<br\>The (Implicit Type) Resource Address format is used | ||
| 3 | BITMAP[1..8] | (Error) State Flags.<br\>Bit 1 = Interface present:<br\>Bit 2 = Interface test:<br\>Bit 6 = Audio test:<br\>Bit 7 = Device dep. test: | ---What is reported for Stations:---<br\>ASLT/ATLB board missing <br\>ASLT/ATLB wire monitoring<br\>Tone Test <br\>Handset Off-Hook timeout | (no active report)<br\>(only failures)<br\>(only changes)<br\>(only failures) |
| 5 | BITMAP[1..8] | Reporting Flags.<br\>Bit 8 = VERBOSE. | <br\>Set by Tone Test started from station. | |
| 6 | UINT1 | Status information 1. | Bits describing ab- and cd- wire errors | |
| 7 | UINT1 | Status information 2. | TouchLine: Tone test signal/noise value.<br\>Telephone: Wire monitor current. | |
| 8 | NET_OBJ_REF | Entity Information field 1 | Directory Number. | |