Search results
Create the page "AS" on this wiki! See also the search results found.
- * <source.phys.no> is [[Physical number]] considered as sender of paging, used for filling in predefined mails. Not used for Free t1 KB (179 words) - 16:15, 4 October 2019
- ...DGE site to public telephones without need to use additional hardware such as MP-114 gateways. The IC-EDGE System connects to a SIP Service Provider on t ...l by default use this number. An exception is if the station is configured as a direct destination in the "internal number" list.9 KB (1,446 words) - 13:06, 26 June 2024
- As an option, it is also possible to play a prerecorded message at the door, s ...ical RCO is assigned to a physical address. The physical address is given as '''Station ID''' + '''Pin Number'''.7 KB (1,107 words) - 11:16, 24 October 2023
- ...e AMC 07.09: No active reporting of reset, so procedure for “device down” as described below was always used. ...] message is sent to the device and the procedure follows the same pattern as described for “Control Up”.13 KB (1,946 words) - 08:21, 8 September 2017
- ...ing a group of stations is limited to maximum 6 stations in one operation. As from software AMC 11.2 this is extended to 16 stations.2 KB (235 words) - 12:51, 30 June 2022
- |align=center|11||[[TEXT16]]||colspan="3"|Message as Text. All spaces if no message.2 KB (269 words) - 16:04, 3 October 2019
- ...open up for a few stations by putting them in a group, and use this group as “give access to” group in the directory number table. ...u make a group of those stations that should not have access, and use that as “block access from” group in the directory number table.6 KB (1,019 words) - 15:43, 20 May 2022
- ..., and enter the IP address of Eth1 (same as entered in the Web interface), as shown in the image above. ...nused user from the left table and enter settings for the Desktop intercom as highlighted in the image below:9 KB (1,490 words) - 12:56, 26 February 2024
- The use of the call handler plugin is licensed as detailed below. Zenitel devices are recognized in the MOBOTIX HUB as ONVIF compatible devices and are added to the system in the same way.21 KB (3,311 words) - 15:46, 25 May 2023
- ...mpany name used in some countries, in other countries the company is known as '''G4S Technology''' or '''G4 Tec'''. '''Symmetry''' is also sold under the *Incoming intercom calls can be treated as alarms where required in critical environments21 KB (3,404 words) - 09:12, 8 April 2024
- ...ne and speaker. The status of the stations is reported to AlphaWeb as well as to 3rd party management systems using SNMP, Syslog, OP C or the STENTOFON S3 KB (534 words) - 13:52, 14 June 2018
- This station is fully supported as form AlphaCom version 10.202 KB (201 words) - 09:20, 16 August 2022
- This station is fully supported as from AlphaCom version 11.2.3.112 KB (205 words) - 09:33, 20 June 2024
- The use of the call handler plugin is licensed as detailed below. Zenitel devices are recognized in the Milestone XProtect system as ONVIF compatible devices and are added to the system in the same way.22 KB (3,426 words) - 15:09, 25 May 2023
- ...s then connected to the AlphaCom Ethernet port directly or on the same LAN as the AlphaCom2 KB (257 words) - 05:34, 25 March 2022
- ...re sent to the display, the synchronous output, the asynchronous output or as digits back to the exchange, depending on the command type. The address range of the incoming messages is divided as follows:15 KB (2,324 words) - 14:05, 14 June 2018
- ...-4156 Added option for using Normally Closed switch on I/O Pins configured as input===2 KB (224 words) - 10:16, 2 May 2024
- This station is fully supported as form AlphaCom version 10.202 KB (214 words) - 09:21, 16 August 2022
- This station is fully supported as form AlphaCom version 10.502 KB (211 words) - 11:43, 21 November 2023
- * Connect the plugbox cable as shown below1 KB (225 words) - 15:25, 23 June 2023