Avaya-Nortel CS1000 v. 7.6
From Zenitel Wiki
This article describes how to configure Avaya Communication Server 1000E R7.6 to interoperate with Zenitel Stentofon Turbine Intercom using SIP Line Gateway- Issue 0.1
Contents
Introduction
The article describe the configuration steps required for Zenitel Stentofon Turbine Intercom to interoperate with Avaya Communication Server 1000E R7.6 using SIP Line Gateway (SLG). The Zenitel Stentofon Turbine Intercom is a door communicator that supports voice transmission using the Session Initiation Protocol (SIP), in addition to being a door entry device. In the compliance testing, the Zenitel Stentofon Turbine Intercom was set up as a 3rd Party SIP Extension on Avaya Communication Server 1000E and underwent testing of various call scenarios with other Avaya telephones and Zenitel Stentofon Turbine Intercom units.
Configuration example
The illustrated configuration is an example for interoperability of Stentofon with CS 1000E. The CS1000E R7.6 runs on the Common Processor Pentium Mobile (CPPM) server as a co-resident configuration. The SLG application on the signaling server co-resides on the CPPM. Element Manager is used to access the SLG which resides on the Unified Communication Management Server which is accessed through the System Manager. SIP and Unistim Avaya 1140 IP Deskphones were configured. Stentofon Turbine is registered to the SLG as a Third Party SIP Client (SIP3). An ISDN-PRI trunk connects the CS1000E to the PSTN.
Equipment and Software
| Equipment/Software | Release/Version |
|---|---|
| Avaya Communication Server 1000E | 7.6 |
| Avaya 1140E IP Telephone | 4.3 SP1 |
| Zenitel STENTOFON Turbine Intercom | Software version: 02.03.3.2 |
Configure Avaya Communication Server 1000E
The configuration operations illustrated in this section are performed using terminal access to the CS1000E over an SSH session. It is implied a working system is already in place and the SIP Line Gateway (SLG) is fully configured. For all other provisioning information such as installation and configuration, please refer to the Avaya product documentation.
Configuring Data block: SLS (SIP Line Services)
Create an SLS Data block using the change command in Overlay 15. Type LD 15 to enter the overlay. The User Agent Prefix (UAPR) is required when configuring the UEXT for each Stentofon Turbine.
LD 15
Prompt Response Description >LD 15 Enter Overlay 15 REQ CHG Change TYPE SLS_DATA SIP Line Services Data block CUST 0 Customer Number SIPL_ON YES SIP Line on UAPR 27 Prefix used to auto-generate the User Agent NMME NO Multimedia Service
Configuring Universal Extension (UEXT)
Configure the UEXT on the CS1000E using the NEW command in overlay 11. Type LD 11 to enter the overlay. At the Key 01 prompt use UAPR as configured in the SLS_DATA Block in the previous section. The SIP User (SIPU) and Station control Password (SCPW) are required when configuring each Stentofon Turbine.
LD 11
Prompt Response Description > LD 11 Enter Overlay 11 REQ: NEW Create New TYPE: UEXT Universal Extension TN 100 0 02 00 Terminal Number DES SIPL Description CUST 0 Customer Number UXTY SIPL Universal Extension Type MCCL YES Maximum Client Count Limit SIPN 0 SIP Line for Nortel SIP3 1 SIP Line for third-party FMCL 0 Fixed Mobility Converged Line SIPU 3020 Required for Stentofon Turbine USER ID NDID 163 Node ID SUPR NO Super User ZONE 1 Bandwidth Zone assigned for IP Sets SCPW 1234 Required for Stentofon Turbine USER Password KEY 00 SCR 3020 0 Key 0 CPND New Calling Party Name Disply Name Stentofon2030 Name Key 01 HOT U 273020 The HOT U number is derived from the UAPR as configured in the SLS_Data plus the Key 0 extension Key 02