View source for Configuration of the IP Vandal Resistant Substation TKIE

{{AEIPS}}
The call button and station LED on the IP Vandal Resistant Substation TKIE must be configured.

==ICX-AlphaCom Mode==

===Call Button===
The call button is connected to input 1. The call button can be configured in two ways, either:

* Input 1 is programmed in AlphaPro as '''DAK 11''' in DAK window. The example shows DAK 11 calling stations in [[Ringing Group Feature|Ringing Group 1]] (6701):
[[File:DAK 11 RingGrp.PNG|thumb|left|700px]]
<br style="clear:both;" />

*  Or as subtype 11 in event 30. The example shows input 1 calling station 101 using event 30:
[[File:Event 30 11 ON.PNG|thumb|left|700px]]
<br style="clear:both;" />

===LED Settings===

Log into the '''station webserver''' and navigate to the I/O settings.
The station LED is from factory wired to output 2.

Choose I/O and set it as Output. 
[[File:Output2.png|thumb|left|700px]]
<br style="clear:both;" />

===Control the LED===
Use the event handler and define situations where the station LED shall be lit:
* Microphone active:
[[File:TKIE_MicOpen.png|thumb|left|700px]]
<br style="clear:both;" />

* Call Request and Ringing Group call with blinking LED:
[[File:TKIE_CRmode.png|thumb|left|700px]]
<br style="clear:both;" />

==IC-Edge Mode==
===Call button===
The call button is connected to input 1, and is by default set as input. The input is programmed in Edge Controller -> System Configuration -> Direct Access Key (DAK) and Buttons and Inputs.
The example below shows how to set up a call to directory number 101. The conversation will be ended if input or call button is pressed during conversation.

[[File:TKIE_Edge_Callbutton.PNG|thumb|left|700px]]
<br style="clear:both;" />

===LED Settings===

[[Advanced_Configuration_Mode_(Edge)|Advanced configuration mode]] must be enabled to make the following changes.

Log into the '''station webserver''' and navigate to the I/O settings.
The station LED is from factory wired to output 2.

Choose I/O and set it as Output. 
[[File:Output2.png|thumb|left|700px]]
<br style="clear:both;" />

===Control the LED===
In Edge controller, go into System Configuration -> Special Setting and select Relay setting.
 
Choose to configure output 2 in the listbox. The recommended settings are shown below:

[[File:TKIE_Edge_Output2.png|thumb|left|700px]]
<br style="clear:both;" />

==SIP Mode==

===Call Button===

The call button is connected to input 1, and is by default set as input. The input is programmed in SIP Configuration -> Direct Access Key (DAK).
The example below shows how to set up a call to directory number 101. The conversation will be ended if input or call button is pressed during conversation.

[[File:TKIE_SIP_CallButton.png|thumb|left|700px]]
<br style="clear:both;" />

===LED Settings===

[[Advanced_Configuration_Mode_(Edge)|Advanced configuration mode]] must be enabled to make the following changes.

Log into the '''station webserver''' and navigate to the I/O settings.
The station LED is from factory wired to output 2.

Choose I/O and set it as Output. 
[[File:TKIE_SIP_io2.png|thumb|left|700px]]
<br style="clear:both;" />

===Control the LED===

In the station web server, go into SIP Configuration -> Relays/Outputs.
 
Choose to configure output 2 in the listbox. The recommended settings are shown below:

[[File:TKIE_SIP_Output2.png|thumb|left|700px]]
<br style="clear:both;" />