Difference between revisions of "Faulty Station Line (Event Type)"
From Zenitel Wiki
| (21 intermediate revisions by 6 users not shown) | |||
| Line 1: | Line 1: | ||
| + | {{AI}} | ||
==Event description== | ==Event description== | ||
{| | {| | ||
|- | |- | ||
| − | |width=" | + | |width="180pt"|'''Event Owner''': |
| − | |width=" | + | |width="500pt"|A station or an [[UDP]] group |
|- | |- | ||
|'''Event type''': || 13 - Faulty station line | |'''Event type''': || 13 - Faulty station line | ||
|- | |- | ||
| − | |'''Subevent''': || | + | |'''Subevent''': || 0 = station faults. <br> 2-27 = failure states related to [[IP-ARIO]] PA control. (AMC 11.02)<br> 100 = Tonetest failures (AMC 11.5.3.4) |
|- | |- | ||
| − | |'''When change to ON''': || | + | |'''When change to ON''': || A station's line monitoring has found a problem or if the whole ASLT board becomes faulty |
|- | |- | ||
| − | |'''When change to OFF''': || | + | |'''When change to OFF''': || A station's line monitoring has found the station OK |
|- | |- | ||
|'''When related to''': || N/A | |'''When related to''': || N/A | ||
|- | |- | ||
|} | |} | ||
| − | <br> | + | <br> |
| + | |||
| + | == Application== | ||
| + | Switch over a PA-system to a standby circuit | ||
== Additional information == | == Additional information == | ||
| − | + | The faulty station event is reported On after reset/power-off of AlphaCom, if the station was removed during the reset. IP stations and SIP stations are reported faulted if not registered within 4-5 minutes after AlphaCom reset (and the station was registered before the reset). (Since AMCD 10.55, {{Bugzilla|204}}) | |
| − | + | There is also a default "Faulty Line" event, which becomes active if one more stations are faulty. This event is used for general line error reporting. The reporting is configured from AlphaPro, Exchange & System -> RCI -> Faults: Faulty Line. Default setting is [[MST - Mail to Station|MST]] 1 0 28, which is by reporting line errors (28) to station 1. | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
[[Category:Event Handler]] | [[Category:Event Handler]] | ||
| + | [[Category:Event types]] | ||
Latest revision as of 16:14, 4 October 2019
Event description
| Event Owner: | A station or an UDP group |
| Event type: | 13 - Faulty station line |
| Subevent: | 0 = station faults. 2-27 = failure states related to IP-ARIO PA control. (AMC 11.02) 100 = Tonetest failures (AMC 11.5.3.4) |
| When change to ON: | A station's line monitoring has found a problem or if the whole ASLT board becomes faulty |
| When change to OFF: | A station's line monitoring has found the station OK |
| When related to: | N/A |
Application
Switch over a PA-system to a standby circuit
Additional information
The faulty station event is reported On after reset/power-off of AlphaCom, if the station was removed during the reset. IP stations and SIP stations are reported faulted if not registered within 4-5 minutes after AlphaCom reset (and the station was registered before the reset). (Since AMCD 10.55, BZ 204)
There is also a default "Faulty Line" event, which becomes active if one more stations are faulty. This event is used for general line error reporting. The reporting is configured from AlphaPro, Exchange & System -> RCI -> Faults: Faulty Line. Default setting is MST 1 0 28, which is by reporting line errors (28) to station 1.