Difference between revisions of "Group Call - Increased volume"
From Zenitel Wiki
(→Prerequisites) |
|||
| Line 58: | Line 58: | ||
In the action strings above, there are two lines that defines the volume. Volume during group call is set to 6 (U6) by the command: | In the action strings above, there are two lines that defines the volume. Volume during group call is set to 6 (U6) by the command: | ||
| − | $VOL N%tmp(0) U6 | + | '''$VOL N%tmp(0) U6''' |
| + | |||
Volume is set to 3 (U3) when the group call is ended by the command: | Volume is set to 3 (U3) when the group call is ended by the command: | ||
| − | $VOL N%tmp(0) U3 | + | '''$VOL N%tmp(0) U3''' |
U6 and U3 can be changed to other values if required. | U6 and U3 can be changed to other values if required. | ||
| − | In %gns(3, %tmp(0) in the example, the 3 stands for group 3 (86), and must be changed if a different group is used | + | In %gns(3, %tmp(0)) in the example, the 3 stands for group 3 (86), and must be changed if a different group is used. |
Note that a standard feature exists, which might be a better alternative: | Note that a standard feature exists, which might be a better alternative: | ||
| − | Group calls with "[[Groups#Group_Call_Setup_Priority|Setup Priority = Alarm]]" will automatically use the [[Volume and handset override|Volume Override feature]] of the AlphaCom, without any additional configuration required. | + | Group calls with "[[Groups#Group_Call_Setup_Priority|Setup Priority = Alarm]]" will automatically use the [[Volume and handset override|Volume Override feature]] of the ICX-AlphaCom, without any additional configuration required. |
| − | [[Category:AlphaCom Applications]] | + | [[Category: AlphaCom Applications]] |
[[Category: ICX-AlphaCom Applications]] | [[Category: ICX-AlphaCom Applications]] | ||
Revision as of 10:28, 25 May 2022
This article describes how to increase the volume of a group call announcement. The volume is set back to default value when the group call is ended.
Prerequisites
- This event is CPU extensive. Maximum members in a group using this feature should not exceed approx. 50 stations. (Not applicable for ICX-AlphaCom)
- Minimum software: AMC version 11.
Configuration
In the following example the volume will be set to level 6 when group call 86 is called from stations in UDP group 2. The volume is set to level 3 (default) when the group call is ended.
When stations outside UDP group 2 dial group call 86 this event will not be triggered, and the volume will not be altered.
In AlphaPro, go to Exchange and System -> Events, press Insert and create the following event:
Actions:
| IF %chg(1,0) |
| tmp 0 "%gns(3,0)" |
| LOOP |
| IF %op(%tmp(0),=,0) |
| STOP |
| ENDIF |
| $VOL N%tmp(0) U6 |
| tmp 0 "%gns(3, %tmp(0))" |
| ENDLOOP |
| STOIP |
| ENDIF |
| tmp 0 "%gns(3,0)" |
| LOOP |
| IF %op(%tmp(0),=,0) |
| STOP |
| ENDIF |
| $VOL N%tmp(0) U3 |
| tmp 0 "%gns(3, %tmp(0))" |
| ENDLOOP |
In the action strings above, there are two lines that defines the volume. Volume during group call is set to 6 (U6) by the command:
$VOL N%tmp(0) U6
Volume is set to 3 (U3) when the group call is ended by the command:
$VOL N%tmp(0) U3
U6 and U3 can be changed to other values if required.
In %gns(3, %tmp(0)) in the example, the 3 stands for group 3 (86), and must be changed if a different group is used.
Note that a standard feature exists, which might be a better alternative: Group calls with "Setup Priority = Alarm" will automatically use the Volume Override feature of the ICX-AlphaCom, without any additional configuration required.