Difference between revisions of "Group Call - Increased volume"
From Zenitel Wiki
(→Configuration) |
|||
| Line 14: | Line 14: | ||
[[File:Application14a.png|500px|left|thumb]] | [[File:Application14a.png|500px|left|thumb]] | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| − | Actions: | + | ;Actions: |
| − | + | IF %chg(1,0) | |
| − | + | tmp 0 "%gns(3,0)" | |
| − | + | LOOP | |
| − | + | IF %op(%tmp(0),=,0) | |
| − | + | STOP | |
| − | + | ENDIF | |
| − | + | $VOL N%tmp(0) U6 | |
| − | + | tmp 0 "%gns(3, %tmp(0))" | |
| − | + | ENDLOOP | |
| − | + | STOIP | |
| − | + | ENDIF | |
| − | + | tmp 0 "%gns(3,0)" | |
| − | + | LOOP | |
| − | + | IF %op(%tmp(0),=,0) | |
| − | + | STOP | |
| − | + | ENDIF | |
| − | + | $VOL N%tmp(0) U3 | |
| − | + | tmp 0 "%gns(3, %tmp(0))" | |
| − | + | ENDLOOP | |
| − | + | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
In the action strings above, there are two lines that defines the volume. Volume during group call is set to 6 (U6) by the command: | In the action strings above, there are two lines that defines the volume. Volume during group call is set to 6 (U6) by the command: | ||
Revision as of 13:35, 25 May 2022
This article describes how to increase the volume of a group call announcement. The volume is set back to default value when the group call is ended.
Prerequisites
- This event is CPU extensive. Maximum members in a group using this feature should not exceed approx. 50 stations. (Not applicable for ICX-AlphaCom)
- Minimum software: AMC version 11.
Configuration
In the following example the volume will be set to level 6 when group call 86 is called from stations in UDP group 2. The volume is set to level 3 (default) when the group call is ended.
When stations outside UDP group 2 dial group call 86 this event will not be triggered, and the volume will not be altered.
In AlphaPro, go to Exchange and System -> Events, press Insert and create the following event:
- Actions
IF %chg(1,0) tmp 0 "%gns(3,0)" LOOP IF %op(%tmp(0),=,0) STOP ENDIF $VOL N%tmp(0) U6 tmp 0 "%gns(3, %tmp(0))" ENDLOOP STOIP ENDIF tmp 0 "%gns(3,0)" LOOP IF %op(%tmp(0),=,0) STOP ENDIF $VOL N%tmp(0) U3 tmp 0 "%gns(3, %tmp(0))" ENDLOOP
In the action strings above, there are two lines that defines the volume. Volume during group call is set to 6 (U6) by the command:
- $VOL N%tmp(0) U6
Volume is set to 3 (U3) when the group call is ended by the command:
- $VOL N%tmp(0) U3
U6 and U3 can be changed to other values if required.
In %gns(3, %tmp(0)) in the example, the 3 stands for group 3 (86), and must be changed if a different group is used.
Note that a standard feature exists, which might be a better alternative: Group calls with "Setup Priority = Alarm" will automatically use the Volume Override feature of the ICX-AlphaCom, without any additional configuration required.