Difference between revisions of "IP Desktop with Video Display - Release Notes"
From Zenitel Wiki
(→Firmware version 1.0) |
|||
(16 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
− | '''Note:''' These release notes are for the | + | '''Note:''' These release notes are for the ''LCD screen'' in the [[IP Desktop Station with Video Display - 1408001635]]. |
− | + | Release notes for the IP desktop station is here: [[:Category:INCA Release notes|INCA Release notes]]. | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | = | + | === Version 2.4 === |
− | == | + | * Improved compatibility with the TCIV station. Due to an unexpected FIN packet the connection was disconnected without the socket resources released. |
− | + | * Increased socket count for better network performance | |
− | |||
− | == | + | === Version 2.3 === |
− | + | * Performance optimization for the UART interface between the Desk Station and the display | |
− | + | ** FreeRTOS Update V9.0.0 | |
+ | ** CMX-CSOS changed Task-TCBs to static | ||
+ | ** UART-Drv of DTC-FIFO changed due to Overflow in HW-RX-Buffers, since the ISR was called too late. | ||
+ | === Version 2.2 === | ||
+ | * Fixed a bug where display text fragments were erroneously displayed | ||
+ | * Added a touch calibration dialog to the display | ||
− | = | + | === Version 2.1 === |
− | == | + | * Fixed a display bug when restarting the station via display |
− | |||
− | Fixed a bug | ||
− | == | + | === Version 2.0 === |
− | + | * Added SIP-/PULSE-Support | |
+ | * Revised display handling and output | ||
− | = | + | === Version 1.13 === |
− | + | * Fixed an index error in the camera type list | |
− | + | * Fixed an endless loop when trying to access an invalid camera URL | |
+ | * The resync timer for the camera stream will now be stopped, when syncronisation is successful | ||
− | == | + | === Version 1.12 === |
− | + | * Fixed a bug when entering an IP address and a subnet mask that don't "fit" | |
− | |||
− | |||
− | |||
− | = | + | === Version 1.11 === |
− | + | * Added factory reset via display | |
− | + | * Increased the length of the camera type name in the dynamic camera type list to 100 characters | |
+ | * Increased the number of cameras to 80 | ||
+ | * Increased camera name to 15 characters | ||
− | == | + | === Version 1.10 === |
− | + | * Removed the MJPG streaming path for Grundig cameras | |
− | + | * Added a dynamic list for up to 3 custom camera types including streaming path | |
− | |||
− | = | + | === Version 1.9 === |
− | + | * Fixed a bug where some display texts weren't cleared correctly | |
− | + | * Added the MJPG streaming path for Grundig cameras | |
− | Fixed a bug where | ||
− | == | + | === Version 1.8 === |
− | + | * Fixed a bug where, in manual camera selection, the first element in the list always required a passcode, even when passcode authentication was disabled | |
− | + | * Changed the URL for Axis cameras from "mjpg/video.mjpg" to "axis- cgi/mjpg/video.cgi" | |
+ | * Changed the MJPG stream function to be compatible with older non-RFC-compliant Axis cameras | ||
+ | * Changed the behavior of the LED (the "auo" DIP message does no longer turn off the LED) | ||
+ | * Fixed a web server bug that was causing problems with digest authentication under IE9+ | ||
+ | * The "aue" DIP message is now ignored | ||
+ | * Changed the fallback settings for username and password to "admin"/"alphaadmin" | ||
+ | * Fixed a bug that incorrectly reconnected a camera, when another camera is manually selected during a connected call | ||
+ | * Changed the LED time base | ||
+ | * The station now displays an error screen when trying to stream a video in the wrong format/resolution | ||
+ | * Fixed a timing problem when trying to connect to the camera of an incoming call, when manual camera selection is active | ||
− | = | + | === Version 1.7 === |
− | + | * Added detection of missing DIP messages | |
− | + | * Changed font to a fixed width font | |
+ | * Increased camera count to 48 | ||
+ | * Added manual camera selection with passcode authentication via display | ||
+ | * Added automatic camera switching, if more than one camera is added to a remote station | ||
+ | * Overhauled the UI and web interface | ||
+ | * Added a download/upload functionality for the camera list | ||
+ | * The station does not need to reboot anymore, after changing the settings | ||
+ | * Added factory reset via web interface | ||
− | == | + | === Version 1.6 === |
− | + | * Fixed a bug where the display wasn't cleared correctly in some cases | |
− | + | * Font improvements (narrow characters are now centered instead of left aligned) | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | = | + | === Version 1.5 === |
− | + | * Implemented encryption of the firmware file | |
− | + | * Workflow adaptation | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | == | + | === Version 1.4 === |
− | + | * Implemented DIP protocol via internal serial interface | |
− | + | * Implemented bootloader with firmware upload via web interface | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
+ | === Version 1.3 === | ||
+ | * Fixed a bug where the LEDs weren't correctly updated in some scenarios | ||
− | = | + | === Version 1.2 === |
− | = | + | * Fixed a problem with the web server, that could cause problems, if someone tries to access the web interface, while the device has initiated a reboot |
− | + | * Fixed a bug where the LEDs weren't correctly switched off when the state changed from "incoming call" to "idle" | |
− | Fixed a bug where | ||
− | == | + | === Version 1.1 === |
− | + | * Fixed a network bug in DHCP mode | |
− | + | * Improved network stability | |
− | = | + | === Version 1.0 === |
− | + | * First release | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | + | [[Category: Release notes]] | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− |
Latest revision as of 09:41, 30 June 2022
Note: These release notes are for the LCD screen in the IP Desktop Station with Video Display - 1408001635.
Release notes for the IP desktop station is here: INCA Release notes.
Contents
Version 2.4
- Improved compatibility with the TCIV station. Due to an unexpected FIN packet the connection was disconnected without the socket resources released.
- Increased socket count for better network performance
Version 2.3
- Performance optimization for the UART interface between the Desk Station and the display
- FreeRTOS Update V9.0.0
- CMX-CSOS changed Task-TCBs to static
- UART-Drv of DTC-FIFO changed due to Overflow in HW-RX-Buffers, since the ISR was called too late.
Version 2.2
- Fixed a bug where display text fragments were erroneously displayed
- Added a touch calibration dialog to the display
Version 2.1
- Fixed a display bug when restarting the station via display
Version 2.0
- Added SIP-/PULSE-Support
- Revised display handling and output
Version 1.13
- Fixed an index error in the camera type list
- Fixed an endless loop when trying to access an invalid camera URL
- The resync timer for the camera stream will now be stopped, when syncronisation is successful
Version 1.12
- Fixed a bug when entering an IP address and a subnet mask that don't "fit"
Version 1.11
- Added factory reset via display
- Increased the length of the camera type name in the dynamic camera type list to 100 characters
- Increased the number of cameras to 80
- Increased camera name to 15 characters
Version 1.10
- Removed the MJPG streaming path for Grundig cameras
- Added a dynamic list for up to 3 custom camera types including streaming path
Version 1.9
- Fixed a bug where some display texts weren't cleared correctly
- Added the MJPG streaming path for Grundig cameras
Version 1.8
- Fixed a bug where, in manual camera selection, the first element in the list always required a passcode, even when passcode authentication was disabled
- Changed the URL for Axis cameras from "mjpg/video.mjpg" to "axis- cgi/mjpg/video.cgi"
- Changed the MJPG stream function to be compatible with older non-RFC-compliant Axis cameras
- Changed the behavior of the LED (the "auo" DIP message does no longer turn off the LED)
- Fixed a web server bug that was causing problems with digest authentication under IE9+
- The "aue" DIP message is now ignored
- Changed the fallback settings for username and password to "admin"/"alphaadmin"
- Fixed a bug that incorrectly reconnected a camera, when another camera is manually selected during a connected call
- Changed the LED time base
- The station now displays an error screen when trying to stream a video in the wrong format/resolution
- Fixed a timing problem when trying to connect to the camera of an incoming call, when manual camera selection is active
Version 1.7
- Added detection of missing DIP messages
- Changed font to a fixed width font
- Increased camera count to 48
- Added manual camera selection with passcode authentication via display
- Added automatic camera switching, if more than one camera is added to a remote station
- Overhauled the UI and web interface
- Added a download/upload functionality for the camera list
- The station does not need to reboot anymore, after changing the settings
- Added factory reset via web interface
Version 1.6
- Fixed a bug where the display wasn't cleared correctly in some cases
- Font improvements (narrow characters are now centered instead of left aligned)
Version 1.5
- Implemented encryption of the firmware file
- Workflow adaptation
Version 1.4
- Implemented DIP protocol via internal serial interface
- Implemented bootloader with firmware upload via web interface
Version 1.3
- Fixed a bug where the LEDs weren't correctly updated in some scenarios
Version 1.2
- Fixed a problem with the web server, that could cause problems, if someone tries to access the web interface, while the device has initiated a reboot
- Fixed a bug where the LEDs weren't correctly switched off when the state changed from "incoming call" to "idle"
Version 1.1
- Fixed a network bug in DHCP mode
- Improved network stability
Version 1.0
- First release