Difference between revisions of "SET CALL REQ MODE"
From Zenitel Wiki
(New page: {| border="1" align=left |- !style="background:#ffdead;" width="90pt" colspan="2"|SET_CALL_REQ_MODE !style="background:#ffdead;" width="100pt"|0x006C !style="background:#ffdead;" width="3...) |
|||
| Line 6: | Line 6: | ||
!style="background:#ffdead;" width="100pt"|AMC 07.00 | !style="background:#ffdead;" width="100pt"|AMC 07.00 | ||
|- | |- | ||
| − | |colspan" | + | |colspan="5"|'''$SCRM L101 L102 U0 U1''' |
|- | |- | ||
| − | Turn on/off message "your call is registered, please wait", then ring/flashing at a station. Note that the station leaves this mode if becomes busy for some reason (dialing, incoming conv.<br\>"Call requester mode" is normally used to inform the user about a successful activation of call request. | + | |colspan="5"|Turn on/off message "your call is registered, please wait", then ring/flashing at a station. Note that the station leaves this mode if becomes busy for some reason (dialing, incoming conv.)<br\>"Call requester mode" is normally used to inform the user about a successful activation of call request. |
|- | |- | ||
| − | |align=center|1||NET_OBJ_REF<br\>{ECL_STATION}||colspan="3"|Station | + | |align=center|1||[[NET_OBJ_REF]]<br\>{[[ECL_STATION]]}||colspan="3"|Station |
|- | |- | ||
| − | |align=center|2||NET_OBJ_REF<br\>{ECL_STATION}||colspan"3"|Station that received the call request mail (i.e. sender of this command) | + | |align=center|2||[[NET_OBJ_REF]]<br\>{[[ECL_STATION]]}||colspan="3"|Station that received the call request mail (i.e. sender of this command) |
|- | |- | ||
| − | |align=center|3|| | + | |align=center|3||[[UINT1]]||colspan="3"|UserDefined Properties ([[UDP]]) of the station that received the call request mail. |
|- | |- | ||
| − | |align=center|4|| | + | |align=center|4||[[UINT1]]||colspan="3"|New call requester mode:<br\> 0 = off<br\>1 = on |
|- | |- | ||
| − | |colspan"2"|Response:||colspan="3"| | + | |colspan="2"|Response:||colspan="3"|[[COMMAND_RESPONSE]] |
|- | |- | ||
|} | |} | ||
Revision as of 13:48, 14 June 2007
| SET_CALL_REQ_MODE | 0x006C | 108 | AMC 07.00 | |
|---|---|---|---|---|
| $SCRM L101 L102 U0 U1 | ||||
| Turn on/off message "your call is registered, please wait", then ring/flashing at a station. Note that the station leaves this mode if becomes busy for some reason (dialing, incoming conv.)<br\>"Call requester mode" is normally used to inform the user about a successful activation of call request. | ||||
| 1 | NET_OBJ_REF<br\>{ECL_STATION} | Station | ||
| 2 | NET_OBJ_REF<br\>{ECL_STATION} | Station that received the call request mail (i.e. sender of this command) | ||
| 3 | UINT1 | UserDefined Properties (UDP) of the station that received the call request mail. | ||
| 4 | UINT1 | New call requester mode:<br\> 0 = off<br\>1 = on | ||
| Response: | COMMAND_RESPONSE | |||