Actions

Difference between revisions of "VSF-Fortitude8 7.4 Release Notes"

From Zenitel Wiki

(→‎Issues fixed)
(→‎Issues fixed)
Line 51: Line 51:
 
The loudspeaker level after boot was always similar to configuration, about +4dB. A configuration change up and down was needed to get back to configured audio level. The audio level shall now be applied as configured after boot.
 
The loudspeaker level after boot was always similar to configuration, about +4dB. A configuration change up and down was needed to get back to configured audio level. The audio level shall now be applied as configured after boot.
  
 +
=== MTN-3910 Uploaded certificates can now be deleted===
 +
The deletion of certificates uploaded in the device web was previously not possible. This is now fixed.
 +
 +
=== MTN-3906 Device now waits for the ONVIF subscription timer to run out before deleting subscription===
 +
Subscription timer for ONVIF messages was running out before the message timer. This is now fixed.
 +
 +
=== MTN-3896 Factory reset audio parameters now affects only Audio Settings page===
 +
Factory reset audio parameters doesn't affect VAD, Tone Test and DAVC settings, only settings which are configured on Audio Settings page.
  
 
<br>
 
<br>

Revision as of 14:28, 1 February 2023

Previous Release - VSF-Fortitude8 7.3 Release Notes

This document provides the release notes for VSF-Fortitude8 7.4 with incremental bug fix releases. The release notes for VSF-Fortitude8 7.4 describe new features, improvements and issues fixed after VSF-Fortitude8 7.3.3.1.

Contents

Release info

Name: VSF-Fortitude8
Description: VSF-Fortitude8 is a firmware for Turbine Plus Intercoms including the following devices: TCIV-2+, TCIV-3+, TCIV-5+, TCIV-6+, TKIV+ and TMIV-1+

The firmware is delivered in two different files:

  • vsff8-7.4.3.x - Used for standard in-field upgrades
  • vsff8-prod-7.4.3.x - Used in production- and recovery upgrades.

Version: 7.3.3.1
Date: 25.11.2022
Status: General Availability

VSF-FORTITUDE8 7.4.3.0

New Features

MTN-3847 Option to disable registration in SIP mode added

A new option, No-Reg, has been added for Registration Method in Account Settings which will prevent registration towards a server. Device can operate in peer to peer mode.


Improvements

MTN-3867 Relay activation is now supported from NxWitness VMS

Added support for <onvifDevice:RelayOutputToken> tag to handle NxWitness implementation.

MTN-3434 SNMP traps are now sent only on registration change state.

For example a trap will be sent when the devices goes from registered to unregistered (or vice versa), it was previously sent after each registration interval even if there were no changes to the state.


Issues fixed

MTN-4008 Syncing is now properly mapped for Alphacom "Noise Reduction" configuration level 0 to 7

The new configuration "Moderate" was not mapped. New mapping:

  • 0: ANC Disabled
  • 1,2: ANC Enabled with Low Suppression
  • 3,4: ANC Enabled with Moderate Suppression
  • 5,6: ANC Enabled with High Suppression
  • 7: ANC Enabled with Very High Suppression

MTN-3958 Changing VoIP port range adds 1000 ports to the start value

Max port number is 65535, if start value is higher than 64535, remaining ports are allocated.

MTN-3952 Added support for disabling factory reset from call button or input

If the checkbox is enabled it's not possible to factory reset the device via call button or input.

MTN-3951 Loudspeaker volume configuration now applied correctly after reboot

The loudspeaker level after boot was always similar to configuration, about +4dB. A configuration change up and down was needed to get back to configured audio level. The audio level shall now be applied as configured after boot.

MTN-3910 Uploaded certificates can now be deleted

The deletion of certificates uploaded in the device web was previously not possible. This is now fixed.

MTN-3906 Device now waits for the ONVIF subscription timer to run out before deleting subscription

Subscription timer for ONVIF messages was running out before the message timer. This is now fixed.

MTN-3896 Factory reset audio parameters now affects only Audio Settings page

Factory reset audio parameters doesn't affect VAD, Tone Test and DAVC settings, only settings which are configured on Audio Settings page.


Known Issues

SUN-476 HTTP MJPEG stream has color distortions when viewed in LenelS2 OnGuard

HTTP MJPEG stream has color distortions when viewed in LenelS2 OnGuard, recommendation is to use RTSP H.264 for video integration instead.

SUN-349 MJPEG stream shows green image in Avigilon

MJPEG stream shows green image in Avigilon, recommendation is to use H.264 for video integration instead.



VSF-FORTITUDE8 7.3.3.0

Issues fixed

MTN-3922 Intercom set to correct device type after software upgrade

Fixed an issue where intercom would be set as a kit after the upgrade.

MTN-3918 AVC - Default value for Far-end Lockout Time changed to 100 ms. Debug in Display now shows 0 dB

Default value for AVC parameter Far-end Lockout Time was set to 1 second. This is now changed to 100 milliseconds. Also, Debug in Display wouldn't show correct value for no gain raise, i.e. 0 dBA raise, this is now fixed, and correct 0 dB value is shown.

MTN-3905 Triggering relay via ONVIF in ICX-AlphaCom mode fixed

Fixed an issue which prevented relay being triggered over ONVIF if station is in ICX-AlphaCom mode

MTN-3882 Fixed DAK function for Volume Control

When DAK function is set to Volume Control, pressing DAK wouldn't raise or lower the gain. This is now fixed, and volume can be configured also with DAK.

MTN-3860 ONVIF issue with AMAG Symmetry fixed

Fixed an issue which prevented station from being added to AMAG Symmetry.


Known Issues

SUN-476 HTTP MJPEG stream has color distortions when viewed in LenelS2 OnGuard

HTTP MJPEG stream has color distortions when viewed in LenelS2 OnGuard, recommendation is to use RTSP H.264 for video integration instead.

SUN-349 MJPEG stream shows green image in Avigilon

MJPEG stream shows green image in Avigilon, recommendation is to use H.264 for video integration instead.

Retrieved from "https://wiki.zenitel.com/w/index.php?title=VSF-Fortitude8_7.4_Release_Notes&oldid=231549"