Latest revision as of 15:58, 27 May 2024

Previous Release - VSF-Fortitude8 8.1 Release Notes

This document provides the release notes for VSF-Fortitude8 8.2 with incremental bug fix releases. The release notes for VSF-Fortitude8 8.2 describe new features, improvements and issues fixed after VSF-Fortitude8 8.1.3.2.

Release info

Name: VSF-Fortitude8
Description: VSF-Fortitude8 is a firmware for Turbine Plus Intercoms including the following devices: TCIV-2+, TCIV-3+, TCIV-5+, TCIV-6+, TKIV+, TMIV-1+, TEIV-1+ and TEIV-4+.

The firmware is delivered in two different files:

vsff8-8.2.3.x - Used for standard in-field upgrades
vsff8-prod-8.2.3.x - Used in production- and recovery upgrades.

Version: 8.2.3.0
Date: 24.05.2024
Status: General Availability

VSF-FORTITUDE8 8.2.3.0

Improvements

DS-899 SIP/SDP support for dynamic payload for codec L16x48 (HD-Audio)

Now supporting SIP media attribute L16/48000 with dynamic payload type in range 96..127. Note! The device needs to be configured in “HD-Audio” mode and voice processing (AEC and NC) is not supported.

DS-802 The keypad backlight of TEIV-1+ is now on in idle state

The backlight will be off if the station is in active or false state.

DS-798 Improved digital zoom

Now image is more clear when zooming. Also possible to zoom down to X4.

DS-781 Reversing procedure for call and opening door on TEIV-1+ with keyboard

To make an intercom call, dial the intercom number. To open the door, dial # then PIN code. On earlier firmware versions it was opposite operation (Intercom call: dial # then intercom number. Door Opening: Dial PIN code.)

Fixed Issues

MTN-4435 RTSP stream could stop in some cases

In case of audio issues, RTSP stream would terminate. Now the stream will continue with a moment of silence instead.

MTN-4403 Sound Detection (VAD) levels were not calibrated correct towards configured input

Since major release 7.0 and newer the audio signal levels have been changed, but the the Sound Detection configured levels was not adjusted making threshold levels significantly off, and not as on 6.x SW and older.

The dBA configured values are now re-calibrated using a TCIV+ as reference. Measure reference level is 0.5 meter in front of station. A Pink noise signal have been used as test signal. The new values shows to be a few dB more sensitive then older 6.x SW but not significant. Note! This is not fine calibrated per product variant so there might be product variations, but all TCIS/TCIV/TFIE should be close in levels.

MTN-4394 Multicast paging working again on intercom devices

Multicast paging was not working on intercom devices when configuring from the webpage. This is now fixed.

MTN-4362 Fixed wrong description in Sound Detection settings

The description of “Minimum time before reactivation” is corrected to “Choose how long to wait before enabling VAD after triggering the DAK key”

MTN-4340 ONVIF backchannel could cut last second of audio

In some cases backchannel could cut around last second of audio when using push to talk or pre-recorded messages that terminate backchannel session.

This does not happen anymore if client sends TEARDOWN command correctly.

MTN-4329 Fixed an issue with wrong intervals for ONVIF events reports

Fixed an issue with wrong parsing of some PullMessages parameters. In some VMSs, PullMessages parameters Timeout and MessageLimit were not parsed correctly on VS-IS8.0.3.2 and wrong values were used.

MTN-4320 Weak cipher suites no longer supported on devices

Removed the AES128-SHA AES128-SHA256:ECDHE-RSA-AES128-SHA:ECDHE-RSA-AES256-SHA:CAMELLIA128-SHA:CAMELLIA256-SHA ciphers reported by security scanner

MTN-4228 Turbine devices could not be used with Bosch VMS

There was a problem on Zenitel ONVIF devices that caused software to crash and device to reboot which made Bosch VMS unable to connect to the device.

Known Issues

MTN-4333 HD-Audio mode not working using digital microphone input

Audio is distorted when digital microphone is used. Audio is OK if using analogue microphone input

MTN-4121 Asterisk discards alternative profiles

Default setting for ITSV-5 sends 3 types (BP & MP & HP). However, Asterisk discards all but the first profile it receives (HP in this case). Since only the "Baseline profile" is supported on the device the video doesn't load. A workaround to this issue is to select "Baseline profile" as the H.264 profile type on the ITSV-5.

The issue has been reported and documented here: https://issues.asterisk.org/jira/browse/ASTERISK-29182

@@ Line 18: / Line 18: @@
 =VSF-FORTITUDE8 8.2.3.0=
-==Fixed Issues==
+== Improvements==
-=== MTN-4420 Cyber security update===
+===DS-899 SIP/SDP support for dynamic payload for codec L16x48 (HD-Audio)===
-A software update to mitigate a critical cyber security issue
+Now supporting SIP media attribute L16/48000 with dynamic payload type in range 96..127.
+Note! The device needs to be configured in “HD-Audio” mode and voice processing (AEC and NC) is not supported.
+===DS-802 The keypad backlight of TEIV-1+ is now on in idle state===
+The backlight will be off if the station is in active or false state.
-==Known Issues==
+===DS-798 Improved digital zoom===
-=== MTN-4333 HD-Audio mode not working using digital microphone input===
+Now image is more clear when zooming. Also possible to zoom down to X4.
-Audio is distorted when digital microphone is used. Audio is OK if using analogue microphone input
-===MTN-4121 Known issue: Asterisk discards alternative profiles===
+===DS-781 Reversing procedure for call and opening door on TEIV-1+ with keyboard===
-Default setting for ITSV-5 sends 3 types (BP & MP & HP). However, Asterisk discards all but the first profile it receives (HP in this case). Since only the "Baseline profile" is supported on the device the video doesn't load. A workaround to this issue is to select "Baseline profile" as the H.264 profile type on the ITSV-5.
+To make an intercom call, dial the intercom number. To open the door, dial # then PIN code. On earlier firmware versions it was opposite operation (Intercom call: dial # then intercom number. Door Opening: Dial PIN code.)
-The issue has been reported and documented here: https://issues.asterisk.org/jira/browse/ASTERISK-29182
 <br>
-=VSF-FORTITUDE8 8.1.3.1=
 ==Fixed Issues==
-=== DS-817 Zenitel Connect Pro 1.1 compatible===
+=== MTN-4435 RTSP stream could stop in some cases===
-Compatible with Zenitel Connect Pro 1.1. No changes for ICX-AlphaCom, SIP and IC-EDGE mode.
+In case of audio issues, RTSP stream would terminate. Now the stream will continue with a moment of silence instead.
-==Known Issues==
-=== MTN-4333 HD-Audio mode not working using digital microphone input===
-Audio is distorted when digital microphone is used. Audio is OK if using analogue microphone input
-===MTN-4121 Known issue: Asterisk discards alternative profiles===
-Default setting for ITSV-5 sends 3 types (BP & MP & HP). However, Asterisk discards all but the first profile it receives (HP in this case). Since only the "Baseline profile" is supported on the device the video doesn't load. A workaround to this issue is to select "Baseline profile" as the H.264 profile type on the ITSV-5.
-The issue has been reported and documented here: https://issues.asterisk.org/jira/browse/ASTERISK-29182
-<br>
-=VSF-FORTITUDE8 8.1.3.0=
+=== MTN-4403 Sound Detection (VAD) levels were not calibrated correct towards configured input===
+Since major release 7.0 and newer the audio signal levels have been changed, but the the Sound Detection configured levels was not adjusted making threshold levels significantly off, and not as on 6.x SW and older.
+The dBA configured values are now re-calibrated using a TCIV+ as reference.
+Measure reference level is 0.5 meter in front of station. A Pink noise signal have been used as test signal.
+The new values shows to be a few dB more sensitive then older 6.x SW but not significant.
+Note! This is not fine calibrated per product variant so there might be product variations, but all TCIS/TCIV/TFIE should be close in levels.
-==Improvements==
+=== MTN-4394 Multicast paging working again on intercom devices===
-===MTN-4156 Added option for using Normally Closed switch on I/O Pins configured as input===
+Multicast paging was not working on intercom devices when configuring from the webpage. This is now fixed.
-The default input configuration is Normally Open and the switch contact needs to close to activate the function. A new option “Input NC” has been added to the I/O Pin configuration, which inverts the default behavior and the function is activated on switch open.
-<br>
+=== MTN-4362 Fixed wrong description in Sound Detection settings===
-==Issues fixed==
+The description of “Minimum time before reactivation” is corrected to
-=== MTN-4346 User experience: Audio output level too low when in open duplex conversation with imx6 and im8 based devices ===
+“Choose how long to wait before enabling VAD after triggering the DAK key”
-The gain was increased after AEC but before the audio signal compander (with AGC function) so transmitted signal level reaches target level of -23 dBFS with “nominal voice input”
-=== MTN-4288 TCIV+ video stream is now working properly with Ganz Control VMS===
+=== MTN-4340 ONVIF backchannel could cut last second of audio===
-There was an issue with video stream in Ganz Control VMS, this is now fixed.
+In some cases backchannel could cut around last second of audio when using push to talk or pre-recorded messages that terminate backchannel session.
-=== MTN-4284 Relay activation by Pin code can now play audio messages ===
+This does not happen anymore if client sends TEARDOWN command correctly.
-Activating of Relay caused by PIN-code function will now trigger audio messages if it is configured.
-=== MTN-4230 Fixed issue where audio is not heard when station is using SRTP===
+=== MTN-4329 Fixed an issue with wrong intervals for ONVIF events reports===
-When stations are registered to a SIP server using TLS, Secure SIP and SRTP, audio was heard only on the caller side. This is now fixed, and audio can be heard on both sides.
+Fixed an issue with wrong parsing of some PullMessages parameters. In some VMSs, PullMessages parameters Timeout and MessageLimit were not parsed correctly on VS-IS8.0.3.2 and wrong values were used.
-=== MTN-4219 'DAVC' and 'Offline Relays' were not visible in the station web menu in ICX-AlphaCom mode===
+=== MTN-4320 Weak cipher suites no longer supported on devices===
-The DAVC and Offline Relays settings are now available in the station web menu in ICX-AlphaCom mode.
+Removed the AES128-SHA AES128-SHA256:ECDHE-RSA-AES128-SHA:ECDHE-RSA-AES256-SHA:CAMELLIA128-SHA:CAMELLIA256-SHA ciphers reported by security scanner
-=== MTN-4217 Allowing underscore in SNMP community string===
+=== MTN-4228 Turbine devices could not be used with Bosch VMS===
-Underscore is now allowed in the SNMP community string.
+There was a problem on Zenitel ONVIF devices that caused software to crash and device to reboot which made Bosch VMS unable to connect to the device.
-=== MTN-4095 Fixed an issue with distorted video when streaming in MJPG format from TCIV+===
-The sensor format configuration for MJPEG stream that was removed earlier has been added back.
 <br>
@@ Line 87: / Line 75: @@
 === MTN-4333 HD-Audio mode not working using digital microphone input===
 Audio is distorted when digital microphone is used. Audio is OK if using analogue microphone input
-===MTN-4121 Known issue: Asterisk discards alternative profiles===
+=== MTN-4121  Asterisk discards alternative profiles===
 Default setting for ITSV-5 sends 3 types (BP & MP & HP). However, Asterisk discards all but the first profile it receives (HP in this case). Since only the "Baseline profile" is supported on the device the video doesn't load. A workaround to this issue is to select "Baseline profile" as the H.264 profile type on the ITSV-5.
 The issue has been reported and documented here: https://issues.asterisk.org/jira/browse/ASTERISK-29182
-<br>

Difference between revisions of "VSF-Fortitude8 8.2 Release Notes"

From Zenitel Wiki