VSF-Fortitude8 8.1 Release Notes

• Previous Release - VSF-Fortitude8 8.0 Release Notes

This document provides the release notes for VSF-Fortitude8 8.1 with incremental bug fix releases. The release notes for VSF-Fortitude8 8.0 describe new features, improvements and issues fixed after VSF-Fortitude8 8.0.3.2.

Release info

Name: VSF-Fortitude8
Description: VSF-Fortitude8 is a firmware for Turbine Plus Intercoms including the following devices: TCIV-2+, TCIV-3+, TCIV-5+, TCIV-6+, TKIV+, TMIV-1+, TEIV-1+ and TEIV-4+.

The firmware is delivered in two different files:

• vsff8-8.1.3.x - Used for standard in-field upgrades
• vsff8-prod-8.1.3.x - Used in production- and recovery upgrades.

Version: 8.1.3.1
Date: 29.02.2024
Status: General Availability

VSF-FORTITUDE8 8.1.3.1

Fixed Issues

DS-817 Zenitel Connect Pro 1.1 compatible

Compatible with Zenitel Connect Pro 1.1. No changes for ICX-AlphaCom, SIP and IC-EDGE mode.

Known Issues

MTN-4333 HD-Audio mode not working using digital microphone input

Audio is distorted when digital microphone is used. Audio is OK if using analogue microphone input

MTN-4121 Known issue: Asterisk discards alternative profiles

Default setting for ITSV-5 sends 3 types (BP & MP & HP). However, Asterisk discards all but the first profile it receives (HP in this case). Since only the "Baseline profile" is supported on the device the video doesn't load. A workaround to this issue is to select "Baseline profile" as the H.264 profile type on the ITSV-5.

The issue has been reported and documented here: https://issues.asterisk.org/jira/browse/ASTERISK-29182

VSF-FORTITUDE8 8.1.3.0

Improvements

MTN-4156 Added option for using Normally Closed switch on I/O Pins configured as input

The default input configuration is Normally Open and the switch contact needs to close to activate the function. A new option “Input NC” has been added to the I/O Pin configuration, which inverts the default behavior and the function is activated on switch open.

Issues fixed

MTN-4346 User experience: Audio output level too low when in open duplex conversation with imx6 and im8 based devices

The gain was increased after AEC but before the audio signal compander (with AGC function) so transmitted signal level reaches target level of -23 dBFS with “nominal voice input”

MTN-4288 TCIV+ video stream is now working properly with Ganz Control VMS

There was an issue with video stream in Ganz Control VMS, this is now fixed.

MTN-4284 Relay activation by Pin code can now play audio messages

Activating of Relay caused by PIN-code function will now trigger audio messages if it is configured.

MTN-4230 Fixed issue where audio is not heard when station is using SRTP

When stations are registered to a SIP server using TLS, Secure SIP and SRTP, audio was heard only on the caller side. This is now fixed, and audio can be heard on both sides.

MTN-4219 'DAVC' and 'Offline Relays' were not visible in the station web menu in ICX-AlphaCom mode

The DAVC and Offline Relays settings are now available in the station web menu in ICX-AlphaCom mode.

MTN-4217 Allowing underscore in SNMP community string

Underscore is now allowed in the SNMP community string.

MTN-4095 Fixed an issue with distorted video when streaming in MJPG format from TCIV+

The sensor format configuration for MJPEG stream that was removed earlier has been added back.

Known Issues

MTN-4333 HD-Audio mode not working using digital microphone input

Audio is distorted when digital microphone is used. Audio is OK if using analogue microphone input

MTN-4121 Known issue: Asterisk discards alternative profiles

Default setting for ITSV-5 sends 3 types (BP & MP & HP). However, Asterisk discards all but the first profile it receives (HP in this case). Since only the "Baseline profile" is supported on the device the video doesn't load. A workaround to this issue is to select "Baseline profile" as the H.264 profile type on the ITSV-5.

The issue has been reported and documented here: https://issues.asterisk.org/jira/browse/ASTERISK-29182