IMT - Basic Intercom System Setup

Overview

The procedure for deploying IP-intercom stations is

1. Planning your system
2. Discovery of intercom devices
3. Identification of intercom devices and assigning a directory number
4. Software upgrade
5. Configuration
6. Verifying configuration

A Wizard will guide you through the procedure.

Planning the installation

Plan your installation by collecting configuration data you would need to setup your system.

Planning an AlphaCom Installation

The table below is an example of data you would need for a typical AlphaCom IP intercom installation.

AlphaCom system parameters

Parameter	Value
Station mode	AlphaCom
AlphaCom site 1	10.4.2.2
IP gateway site 1	10.4.2.1
IP address range site 1	10.4.2.x
IP network mask site 1	255.255.255.0
AlphaCom site 2	10.7.2.2
IP gateway site 2	10.7.2.1
IP address range site 2	10.7.2.x
IP network mask site 2	255.255.255.0

AlphaCom system intercom information

Dir. No.	Name	Location (Site)	IP configuration	MAC-address *	Host name	Other
101	Hans	B1, F1, R1	10.4.2.7	00:13:CB:01:5F:27	Zenitel-101
102	Thomas	B1, F1, R2	10.4.2.8	00:13:CB:06:01:4C	Zenitel-102
103	Front door	B1, Main Entrance	10.4.2.9	00:13:CB:00:AA:38	Zenitel-103	Noisy environment
104	Back door	B1, Back Door	10.4.2.10	00:13:CB:00:1B:CA	Zenitel-104
201	Emil	B2, F3, R6	DHCP	00:13:CB:01:5F:28	DHCP
202	Frano	B2, F3, R8	DHCP	00:13:CB:06:01:45	DHCP
203	Lab	B2, Lab Entrance	DHCP	00:13:CB:00:AA:39	DHCP
204	Datacenter	B2, Data Center	DHCP	00:13:CB:00:1B:CE	DHCP

*Note that you don’t need to obtain all the MAC addresses upfront. The AlphaCom directory report from the Discovery Wizard Finish step has MAC addresses in the directory list.

Planning a Pulse Installation

The tables below are examples of data you would require for a typical Pulse system installation.

Pulse system parameters

Parameter	Value
Station mode	Pulse
Server site	192.16.8.29
IP gateway site	192.16.8.1
IP address range site	192.16.8.x
IP network mask site	255.255.255.0

Pulse system intercom information

Dir. No.	Name	Location (Site)	IP configuration	MAC-address	Host name	Other
101	Reception	Reception	192.16.8.29	00:13:cb:00:32:d0	Flush Master	IP Master Station
102	John Smith	Head Office	DHCP	00:13:cb:02:5d:94	Desk Master	IP Desktop Station
103	Peter Brink	Head Office	DHCP	00:13:cb:02:5c:8e	Desk Master	IP Desktop Station
201	Entrance	Main Entrance	DHCP	00:13:cb:06:3a:3e	TCIV-3	IP Substation
202	Elevator	Main Hall	DHCP	00:13:cb:08:00:fe	TMIS-1	IP Substation
301	Office 1	1st floor	DHCP	00:13:cb:06:of:9e	TCIS-5	IP Substation
302	Office 2	2nd floor	DHCP	00:13:cb:06:2a:54	TCIS-4	IP Substation
303	Office 3	3rd floor	DHCP	00:13:cb:06:06:22	TCIS-6	IP Substation

Planning a SIP Installation

The tables below are examples of data you would require for a typical SIP IP intercom installation.

SIP system parameters

Parameter	Value
Station mode	SIP
Server site	192.16.8.100
IP gateway site	192.16.8.1
IP address range site	192.16.8.x
IP network mask site	255.255.255.0

SIP system intercom information

Dir. No.	Name	Location (Site)	IP configuration	MAC-address	Host name	Other
101	Reception	Reception	192.16.8.29	00:13:cb:00:32:d0	Flush Master	IP Master Station
102	John Smith	Head Office	192.16.8.18	00:13:cb:02:5d:94	Desk Master	IP Desktop Station
103	Peter Brink	Head Office	192.16.8.19	00:13:cb:02:5c:8e	Desk Master	IP Desktop Station
201	Entrance	Main Entrance	192.16.8.32	00:13:cb:06:3a:3e	TCIV-3	IP Substation
202	Elevator	Main Hall	192.16.8.34	00:13:cb:08:00:fe	TMIS-1	IP Substation
301	Office 1	1st floor	192.16.8.35	00:13:cb:06:of:9e	TCIS-5	IP Substation
302	Office 2	2nd floor	192.16.8.36	00:13:cb:06:2a:54	TCIS-4	IP Substation
303	Office 3	3rd floor	192.16.8.39	00:13:cb:06:06:22	TCIS-6	IP Substation

Station Discovery and Upgrade Wizard

Once the system has been planned it is time to start VS-IMT and run the Wizard.

• IMT - Discover Stations
• IMT - Identify Stations
• IMT - Discover & Upgrade
• IMT - Configure Zenitel Devices
• IMT - Review Results