Difference between revisions of "IMT - Basic Intercom System Setup"
From Zenitel Wiki
| Line 15: | Line 15: | ||
Plan your installation by collecting configuration data you would need to setup your system. | Plan your installation by collecting configuration data you would need to setup your system. | ||
| − | === Planning an AlphaCom Installation === | + | === Planning an IC-Edge Installation === |
| + | IC-Edge systems should be configured from the [[Edge Controller|IC-Edge Controller]], Use IMT only for firmware upgrade. | ||
| + | |||
| + | === Planning an ICX-AlphaCom Installation === | ||
The table below is an example of data you would need for a typical AlphaCom IP intercom installation. | The table below is an example of data you would need for a typical AlphaCom IP intercom installation. | ||
Revision as of 14:24, 16 August 2022
Contents
Overview
The procedure for deploying IP-intercom stations is
- Planning your system
- Discovery of intercom devices
- Identification of intercom devices and assigning a directory number
- Software upgrade
- Configuration
- Verifying configuration
A Wizard will guide you through the procedure.
Planning the installation
Plan your installation by collecting configuration data you would need to setup your system.
Planning an IC-Edge Installation
IC-Edge systems should be configured from the IC-Edge Controller, Use IMT only for firmware upgrade.
Planning an ICX-AlphaCom Installation
The table below is an example of data you would need for a typical AlphaCom IP intercom installation.
AlphaCom system parameters
| Parameter | Value |
|---|---|
| Station mode | AlphaCom |
| AlphaCom site 1 | 10.4.2.2 |
| IP gateway site 1 | 10.4.2.1 |
| IP address range site 1 | 10.4.2.x |
| IP network mask site 1 | 255.255.255.0 |
| AlphaCom site 2 | 10.7.2.2 |
| IP gateway site 2 | 10.7.2.1 |
| IP address range site 2 | 10.7.2.x |
| IP network mask site 2 | 255.255.255.0 |
AlphaCom system intercom information
| Dir. No. | Name | Location (Site) | IP configuration | MAC-address * | Host name | Other |
|---|---|---|---|---|---|---|
| 101 | Hans | B1, F1, R1 | 10.4.2.7 | 00:13:CB:01:5F:27 | Zenitel-101 | |
| 102 | Thomas | B1, F1, R2 | 10.4.2.8 | 00:13:CB:06:01:4C | Zenitel-102 | |
| 103 | Front door | B1, Main Entrance | 10.4.2.9 | 00:13:CB:00:AA:38 | Zenitel-103 | Noisy environment |
| 104 | Back door | B1, Back Door | 10.4.2.10 | 00:13:CB:00:1B:CA | Zenitel-104 | |
| 201 | Emil | B2, F3, R6 | DHCP | 00:13:CB:01:5F:28 | DHCP | |
| 202 | Frano | B2, F3, R8 | DHCP | 00:13:CB:06:01:45 | DHCP | |
| 203 | Lab | B2, Lab Entrance | DHCP | 00:13:CB:00:AA:39 | DHCP | |
| 204 | Datacenter | B2, Data Center | DHCP | 00:13:CB:00:1B:CE | DHCP |
*Note that you don’t need to obtain all the MAC addresses upfront. The AlphaCom directory report from the Discovery Wizard Finish step has MAC addresses in the directory list.
Planning a Pulse Installation
The tables below are examples of data you would require for a typical Pulse system installation.
Pulse system parameters
| Parameter | Value |
|---|---|
| Station mode | Pulse |
| Server site | 192.16.8.29 |
| IP gateway site | 192.16.8.1 |
| IP address range site | 192.16.8.x |
| IP network mask site | 255.255.255.0 |
Pulse system intercom information
| Dir. No. | Name | Location (Site) | IP configuration | MAC-address | Host name | Other |
|---|---|---|---|---|---|---|
| 101 | Reception | Reception | 192.16.8.29 | 00:13:cb:00:32:d0 | Flush Master | IP Master Station |
| 102 | John Smith | Head Office | DHCP | 00:13:cb:02:5d:94 | Desk Master | IP Desktop Station |
| 103 | Peter Brink | Head Office | DHCP | 00:13:cb:02:5c:8e | Desk Master | IP Desktop Station |
| 201 | Entrance | Main Entrance | DHCP | 00:13:cb:06:3a:3e | TCIV-3 | IP Substation |
| 202 | Elevator | Main Hall | DHCP | 00:13:cb:08:00:fe | TMIS-1 | IP Substation |
| 301 | Office 1 | 1st floor | DHCP | 00:13:cb:06:of:9e | TCIS-5 | IP Substation |
| 302 | Office 2 | 2nd floor | DHCP | 00:13:cb:06:2a:54 | TCIS-4 | IP Substation |
| 303 | Office 3 | 3rd floor | DHCP | 00:13:cb:06:06:22 | TCIS-6 | IP Substation |
Planning a SIP Installation
The tables below are examples of data you would require for a typical SIP IP intercom installation.
SIP system parameters
| Parameter | Value |
|---|---|
| Station mode | SIP |
| Server site | 192.16.8.100 |
| IP gateway site | 192.16.8.1 |
| IP address range site | 192.16.8.x |
| IP network mask site | 255.255.255.0 |
SIP system intercom information
| Dir. No. | Name | Location (Site) | IP configuration | MAC-address | Host name | Other |
|---|---|---|---|---|---|---|
| 101 | Reception | Reception | 192.16.8.29 | 00:13:cb:00:32:d0 | Flush Master | IP Master Station |
| 102 | John Smith | Head Office | 192.16.8.18 | 00:13:cb:02:5d:94 | Desk Master | IP Desktop Station |
| 103 | Peter Brink | Head Office | 192.16.8.19 | 00:13:cb:02:5c:8e | Desk Master | IP Desktop Station |
| 201 | Entrance | Main Entrance | 192.16.8.32 | 00:13:cb:06:3a:3e | TCIV-3 | IP Substation |
| 202 | Elevator | Main Hall | 192.16.8.34 | 00:13:cb:08:00:fe | TMIS-1 | IP Substation |
| 301 | Office 1 | 1st floor | 192.16.8.35 | 00:13:cb:06:of:9e | TCIS-5 | IP Substation |
| 302 | Office 2 | 2nd floor | 192.16.8.36 | 00:13:cb:06:2a:54 | TCIS-4 | IP Substation |
| 303 | Office 3 | 3rd floor | 192.16.8.39 | 00:13:cb:06:06:22 | TCIS-6 | IP Substation |
Station Discovery and Upgrade Wizard
Once the system has been planned it is time to start IMT and run the Wizard.