Difference between revisions of "Touchless sensor (w/ backbox)"
From Zenitel Wiki
(→Configuration in ICX-AlphaCom) |
(→Highlights) |
||
(11 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
− | [[File:2390020100 touchless sensor 1.jpg|thumb| | + | [[File:2390020100 touchless sensor 1.jpg|thumb|200px|right|Touchless sensor, item 2390020100]] |
− | The '''Touchless sensor''' (item 2390020100) is an IR-sensor that connects to | + | The '''Touchless sensor''' (item 2390020100) is an IR-sensor that connects to Zenitel IP stations, and is used to activate calls with gesture recognition instead of pressing the call button. |
+ | |||
+ | The sensor button is powered by 5 volts. Most Zenitel IP stations has a built-in 5V output which can be used to power the sensor button. | ||
== Highlights == | == Highlights == | ||
+ | <div style="float:right;"> <youtube width="350" height="210">3yYBW2ADsNI</youtube> </div> | ||
* Input Voltage: 5V | * Input Voltage: 5V | ||
* Available contacts: Normally Open & Normally Closed | * Available contacts: Normally Open & Normally Closed | ||
Line 13: | Line 16: | ||
Connections are made to the switch using the supplied 5 pin plug. <br> | Connections are made to the switch using the supplied 5 pin plug. <br> | ||
Correct orientation of the plug is ensured by the connector locating guides. | Correct orientation of the plug is ensured by the connector locating guides. | ||
+ | |||
=== Color code === | === Color code === | ||
* Red - +5 Volt supply | * Red - +5 Volt supply | ||
Line 25: | Line 29: | ||
== Use Case Examples == | == Use Case Examples == | ||
− | Touchless sensor | + | Touchless sensor - wiring example: |
− | [[File:Touchless sensor wiring example.png|thumb|500px|left|Touchless sensor | + | |
+ | [[File:Touchless sensor wiring example.png|thumb|500px|left|Touchless sensor wired to Input 1 on a Turbine station]] | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
Line 55: | Line 60: | ||
More information is found under [[Users & Stations (AlphaPro)#DAK|DAK programming]]. | More information is found under [[Users & Stations (AlphaPro)#DAK|DAK programming]]. | ||
− | [[Category: | + | ==Related Information== |
+ | * [http://www.zenitel.com/product/touchless-sensor Additional Documentation on Zenitel.com] | ||
+ | |||
+ | [[Category:Turbine Backboxes and accessories]] |
Latest revision as of 09:21, 24 October 2023
The Touchless sensor (item 2390020100) is an IR-sensor that connects to Zenitel IP stations, and is used to activate calls with gesture recognition instead of pressing the call button.
The sensor button is powered by 5 volts. Most Zenitel IP stations has a built-in 5V output which can be used to power the sensor button.
Contents
Highlights
- Input Voltage: 5V
- Available contacts: Normally Open & Normally Closed
- Sensor active time: 0,5 secs
- Operating distance: 15cm
- IP66
Connections
Connections are made to the switch using the supplied 5 pin plug.
Correct orientation of the plug is ensured by the connector locating guides.
Color code
- Red - +5 Volt supply
- Brown - 0 Volt supply
- Green - Normally Closed
- Blue - Common
- Purple - Normally Open
Typical Application
Use Case Examples
Touchless sensor - wiring example:
Configuration on IC-Edge
- To configure the Input select Edge Controller > System Configuration > Direct Access Keys.
- Select Show/Hide Settings on the station you want to configure.
- Configure the Input to Call To, and enter the directory number to call when activated.
More details can be found on Direct Access Key Settings.
Configuration in ICX-AlphaCom
To configure the input to call a preconfigured number:
- Select Users & Stations
- Select the intercom station to which the touchless sensor is connected
- Open the DAK window
- Select the tab DAK 11-20
- On DAK 11 (= input 1(*)) enter the directory number to call when the input is activated
(*) Input 1 - 6 on Turbine stations are mapped to DAK 11 - 16.
More information is found under DAK programming.