Actions

Difference between revisions of "Touchless sensor (w/ backbox)"

From Zenitel Wiki

(Highlights)
 
(4 intermediate revisions by 2 users not shown)
Line 2: Line 2:
  
 
The '''Touchless sensor''' (item 2390020100) is an IR-sensor that connects to Zenitel IP stations, and is used to activate calls with gesture recognition instead of pressing the call button.
 
The '''Touchless sensor''' (item 2390020100) is an IR-sensor that connects to Zenitel IP stations, and is used to activate calls with gesture recognition instead of pressing the call button.
 +
 +
The sensor button is powered by 5 volts. Most Zenitel IP stations has a built-in 5V output which can be used to power the sensor button.
  
 
== Highlights ==
 
== Highlights ==
<div style="float:right;"> <youtube width="350" height="210">YD-qGSApQPw</youtube>  </div>
+
<div style="float:right;"> <youtube width="350" height="210">3yYBW2ADsNI</youtube>  </div>
 
* Input Voltage: 5V
 
* Input Voltage: 5V
 
* Available contacts: Normally Open & Normally Closed
 
* Available contacts: Normally Open & Normally Closed
Line 58: Line 60:
 
More information is found under [[Users & Stations (AlphaPro)#DAK|DAK programming]].
 
More information is found under [[Users & Stations (AlphaPro)#DAK|DAK programming]].
  
[[Category:Additional equipment]]
+
==Related Information==
 +
* [http://www.zenitel.com/product/touchless-sensor Additional Documentation on Zenitel.com]
 +
 
 +
[[Category:Turbine Backboxes and accessories]]

Latest revision as of 09:21, 24 October 2023

Touchless sensor, item 2390020100

The Touchless sensor (item 2390020100) is an IR-sensor that connects to Zenitel IP stations, and is used to activate calls with gesture recognition instead of pressing the call button.

The sensor button is powered by 5 volts. Most Zenitel IP stations has a built-in 5V output which can be used to power the sensor button.

Highlights

  • Input Voltage: 5V
  • Available contacts: Normally Open & Normally Closed
  • Sensor active time: 0,5 secs
  • Operating distance: 15cm
  • IP66

Connections

Connections are made to the switch using the supplied 5 pin plug.
Correct orientation of the plug is ensured by the connector locating guides.

Color code

  • Red - +5 Volt supply
  • Brown - 0 Volt supply
  • Green - Normally Closed
  • Blue - Common
  • Purple - Normally Open

Typical Application

Touchless sensor - general wiring


Use Case Examples

Touchless sensor - wiring example:

Touchless sensor wired to Input 1 on a Turbine station


Configuration on IC-Edge

  • To configure the Input select Edge Controller > System Configuration > Direct Access Keys.
  • Select Show/Hide Settings on the station you want to configure.
  • Configure the Input to Call To, and enter the directory number to call when activated.
Input 1 configured to call number 13 when triggered


More details can be found on Direct Access Key Settings.

Configuration in ICX-AlphaCom

To configure the input to call a preconfigured number:

  1. Select Users & Stations
  2. Select the intercom station to which the touchless sensor is connected
  3. Open the DAK window
  4. Select the tab DAK 11-20
  5. On DAK 11 (= input 1(*)) enter the directory number to call when the input is activated
Input 1 configured to call number 13 when triggered


(*) Input 1 - 6 on Turbine stations are mapped to DAK 11 - 16.

More information is found under DAK programming.

Related Information