Audio Settings (Devices)

This article describes the Audio Settings for devices running firmware version 7.1 or later. For description of older versions see Audio Settings (SIP) - older versions

From the Audio Settings page one can set loudspeaker volume, enable various audio signal processing feature and more.

Accessing the Audio Settings page

How to access the Audio Settings page depends on the mode of operation:

• Edge mode: Edge Configuration > Audio Settings
• SIP mode: SIP Configuration > Audio Settings
• ICX-AlphaCom mode: Advanced ICX-AlphaCom > Audio Settings

Available settings depends on device type and whether or not accessories are selected. More options become available when enabling Advanced Configuration mode.

Normal Mode

"Normal mode" is the default view in the device web interface. One can set the level of the internal loudspeaker, as well as Line Out level and the output level on any accessories connected (e.g. handset, headset or external speaker).

In addition one can enable Automatic Gain Control (AGC), Active Noise Cancellation (ANC) and Automatic Volume Control (AVC). Not all these features are available for all types of devices.

Audio Settings - Normal mode

• The available volume range for the loudspeaker depends on the intercom/device type. See this table for details.
• When the loudspeaker volume is set to 0dB (default) it will produce a nominal loudspeaker output of 65 dBA at 0.5 meter distance.

Devices in ICX-AlphaCom mode

When a device is used in ICX-AlphaCom mode the following settings are controlled by the ICX-AlphaCom server, and configured from AlphaPro:

• Internal Loudspeaker volume
• Automatic Noise Cancellation (ANC)
• Line Out level

These settings should not be changed in the device web interface, as they will be overwritten by the settings done from AlphaPro.

Volume settings controlled from AlphaPro

Advanced Configuration Mode

When selecting Advanced Configuration mode in the top right corner of the web interface, the Audio Settings page will change, and is divided into the following sections:

• Audio Outputs
• Audio Inputs
• Audio signal processing
• Other Audio Related Config (available in ICX-AlphaCom mode only)

Audio Settings - Advanced Configuration mode

Audio Outputs

Available settings depends on device type and whether or not accessories are selected.

Audio Output settings - Advanced Configuration mode

• Internal Loudspeaker: The value in the left field ("Gain") sets the regular volume. The value in the right field ("Override Gain") sets the volume when the Volume Override feature is active. For details, see here (Edge) and here (ICX-AlphaCom).
• On Turbine devices the "audio source" for playing in the speaker can be selected:
  • Main Audio Line: Play audio from VoIP signal (default)
  • Pure Line IN Signal: When the device is in idle play audio from the Line IN input. When the device is in a call, play audio from the VoIP signal
  • Pure Line In+GPIO: When the device is in idle play audio from the Line IN input if Input 6 is active. When the device is in a call, play audio from the VoIP signal
• Handset Loudspeaker: Sets the level for regular volume (left filed) and Volume Override (right field). This setting appears only when Accessories = Handset (or Headset) is selected.
• Line Out: The value in the left field ("Gain") sets the regular volume. The value in the right field ("Override Gain") sets the volume when the Volume Override feature is active.
• Additional options available when "No Accessory" is selected:
  • Main Audio Line: Play audio from VoIP signal
  • Pure Mic Signal: Audio from microphone without any signal processing
  • Processed Mic Signal: Audio from microphone with signal processing

• Selective PA: Used for special application. Leave it disabled.
• Force Loudspeaker Ringing: Enable the ringing signal from an incoming call to be heard in the internal loudspeaker if a headset, handset or external loudspeaker is used.

Stations with additional output for External Loudspeaker:
The IP Flush Master, IP-CROR and the TFIX-V2 series of stations have an additional output for external loudspeaker. This loudspeaker output needs to be enabled from the web interface, and volume can be configured separately from the internal speaker:

External Loudspeaker configuration

Audio Inputs

In this menu you select the input gain for the internal microphone, and other input sources that might be connected to the device.

You should normally not change the "Internal Microphone Gain" for "standard products". This gain is calibrated for these products to avoid clipping or feedback from loudspeaker to mic, and to produce a "nominal voice signal" with talker at "nominal distance". The microphone gain configuration is mainly intended for Kits with unknown microphone or for finetuning/calibration of component variations in known products.

If the device has headset or handset connected, the gain from this microphone can be adjusted separately:

Audio Input options in a Desktop station with handset

On devices with Analog Line In option (e.g. TKIE kit), you can choose to use the microphone or the Line In as input source (only when "No Accessory" is selected):

Audio Input options in TKIE kit - The microphone is disabled when the Line In is enabled

On devices with a digital MEMS microphone (e.g. TCIS and TCIV+ stations), one can choose to use an external electret mic instead.

Audio Input options in TCIV+ station

• Electret Mic: Use an electret microphone connected to the the analog mic input instead of the digital microphone.
• Digital Mic (default): Use the built-in MEMS microphone

There is also an option to switch between the internal digital mic and an external microphone by activating an input. This makes it possible to connect a handset or headset to TCIS/TCIV+, and connect the hook-switch of the handset to the input. One can choose which input to use for the hook-switch.

• I/O Pin A>D Switch: When the input is triggered, the analog mic input (e.g. handset) is enabled. When the input is not triggered, the digital mic is enabled. The input must be configured as "Input" in the IO Settings page.
• I/O Pin A>D Switch (until call-end): When the input is triggered, the analog mic input (e.g. handset) is enabled. When the call is ended the digital mic is enabled.

Switch between analog mic and digital mic by input 5 (= hook-switch). Mute the loudspeaker when the handset (= analog mic) is in use

New default settings

IP Intercom

The IP-station audio output has been normalized based on ITU recommendations. The input signal which is used for the output measurements is an ITU Voice Signal with an average RMS energy of -23 dBFS. Output levels are measured at a distance of 0.5 meter. The actual SPL of the IP-CROR station is 3 dB lower than indicated in the table below due to the covering of the speaker grill with a foil.
Kit output levels are based on the same speaker arrangement as for the comparable station.

Product family	Gain range
	Minimum	Default	Maximum	Override maximum
TCIS/TICV/TCIV+/TKIV+/TKIS	-10	0	+13	+23
TFIE/TKIE	-10	0	+18	+28
TMIS/TMIV+	-17	0	+4	+14
ECPIR	-17	0	+4	+14
TFIX	-10	0	+3	+4
TFIX-V2	-10	0	+3	+4
IP Desk Master (100840xxxx)	-8	0	+16	+18
IP Flush Master (1008431000)	-14	0	+10	+12
IP-Station, Clean Room/OR (1008415000)	-14	0	+10	+12

IP Speakers

The IP Speaker audio output has been normalized based on ITU recommendations. The input signal which is used for the output measurements is an ITU Voice Signal with an average RMS energy of -23 dBFS. Output levels are measured at a distance of 1.0 meter

Product family	Gain range
	Minimum	Default	Maximum	Override maximum
ELSII-10WM	-10	10	+16	+17
ELSIR-10CM	-10	10	+16	+17
ELSII-10HM	0	10	+29	+30
ELSII-10LHM	0	10	+35	+36
ELSII-10PM	-10	10	+13	+14