Actions

Difference between revisions of "GSM gateway (Mobile VoIP)"

From Zenitel Wiki

(→‎Routing of calls from Mobile to AlphaCom)
(→‎Related articles)
 
(196 intermediate revisions by 6 users not shown)
Line 1: Line 1:
−
This article describes the setup of the GSM gateway MV-370 from [http://www.portech.com.tw PORTech Communications Inc]
+
{{AI}}
−
[[Image:SIP GSM Gateway.jpg|thumb|right|Configuration example]]
+
[[Image:2200003000 RS.jpg|thumb|600px|GSM Gateway MV-370]]
  
−
== Configuration of the MV-370==
+
Alternative solution: [[IP Telephony Service (ICX-AlphaCom)]]
−
The MV-370 unit is configured via a web interface. The default IP address is 192.168.0.100. Before accessing the web page, confirm that the IP address of the configuration PC is on the same subnet, e.g. 192.168.x.x.
 
  
−
*Username: voip
+
__TOC__
−
*Password: 1234
 
  
−
=== Network settings ===
+
This article describes the setup of the GSM gateway MV-370 (Mobile VoIP) for communication with the ICX system or the AlphaCom.
 +
 
 +
The GSM Gateway must be equipped with a SIM card and registered to the GSM network as a regular mobile phone subscriber. Via the gateway calls can be made from the ICX or AlphaCom to the GSM network, as well as from the GSM network in to the ICX/AlphaCom.
 +
 
 +
[[Image:MV370 ICX.png|thumb|left|500px|GSM Gateway]]
 +
<br style="clear:both;" />
 +
 
 +
It is also possible to [[Send SMS messages from ICX-AlphaCom|send SMS messages from the ICX/AlphaCom]] via the GSM gateway.
 +
 
 +
==Licenses==
 +
 
 +
*'''AlphaCom''': [[Licenses#SIP_trunk_license|License for SIP Trunk, 100 9642 001]]. One license for each connected gateway.
 +
*'''ICX''': [[Licenses for ICX-500 and ICX-AlphaCom Core|ILI-SIP2 SIP Trunking, 2 lines, 1002602101]]. One license can serve two gateways.
 +
 
 +
==GSM Gateway Configuration==
 +
'''Important:''' If you have a SIM card with PIN code activated, '''DO&nbsp;NOT'''&nbsp;insert the SIM card yet.
 +
 
 +
 
 +
===Load Factory Default values===
 +
The GSM Gateway comes with default network parameters (factory default parameters). The default IP address is '''192.168.0.100'''.
 +
 
 +
You can load factory network parameters and reset the username and password to its default settings (username: '''voip''', password: '''1234''') by following these steps:
 +
 
 +
#Press and hold the button SW1 located at the bottom of the unit (you have to remove the lid) for about 7-8 seconds
 +
#Wait for the "Mobile" and "LAN" leds to start blinking
 +
 
 +
[[File:GSM FactoryDef.PNG|left|500px|thumb|Set default IP Address: Press SW1 for 7-8 seconds]]
 +
<br style="clear:both;" />
 +
 
 +
 
 +
*The GSM Gateway will now get the IP address '''192.168.0.100''', subnet mask 255.255.255.0.
 +
 
 +
===Accessing the gateway===
 +
 
 +
*Change the IP address of your '''PC to 192.168.0.99''', subnet mask 255.255.255.0.
 +
*Connect the LAN port of the PC to the Ethernet port of the GSM Gateway.
 +
*Start your Web Browser and type 192.168.0.100 in the URL field.
 +
*Type in username '''voip''' and password '''1234'''. (Case-sensitive!)
 +
 
 +
[[File:GSM accessing.PNG|left|500px|thumb|Accessing the gateway]]
 +
<br style="clear:both;" />
 +
 
 +
 
 +
*The Home page of the Web Interface will appear:
 +
 
 +
[[File:GSM Home.PNG|thumb|left|500px|Homepage of the GSM Gateway]]
 +
<br style="clear:both;" />
 +
 
 +
===Network settings===
 
Change the network settings according to the network environment. Select '''Network > WAN Settings''':
 
Change the network settings according to the network environment. Select '''Network > WAN Settings''':
−
* '''IP Type''' = Enable ''Fixed IP''
 
−
* '''IP''' = IP address of the Mobile VoIP unit
 
−
* '''Mask''' = Network mask
 
−
* '''Gateway''' = IP address of the network gateway
 
  
−
=== Route settings ===
+
:*'''IP Type''' = Enable ''Fixed IP''
−
====Routing of calls from Mobile to AlphaCom====
+
:*'''IP''' = IP address of the Mobile VoIP unit
 +
:*'''Mask''' = Network mask
 +
:*'''Gateway''' = IP address of the network gateway <br style="clear:both;" />
 +
 
 +
[[Image:MV-370-WAN.PNG|left|thumb|500px|Network Settings]]
 +
<br style="clear:both;" />
 +
 
 +
 
 +
===Mobile settings===
 +
Go to '''Mobile''' > '''Settings''' and define the following parameters:
 +
 
 +
*'''SIP From''' = User/Tel (Not Reg)
 +
*'''Mobile PIN Code''' = ON. Code: Enter the PIN code for the SIM card. Confirmed: Enter the PIN code again.
 +
 
 +
[[Image:MV-370-MobileSettings.PNG|left|thumb|500px|Mobile settings]]
 +
<br style="clear:both;" />
 +
 
 +
 
 +
 
 +
The SIM card can now be inserted. The gateway uses Standard (Mini) SIM card (15x25mm).
 +
[[File:GSM SIM Placement.PNG|thumb|left|300px|SIM card placement]]
 +
<br style="clear:both;" />
 +
 
 +
After the SIM card is inserted, you can check that the gateway is successfully registered to the GSM network in '''Mobile''' > '''Status'''.
 +
 
 +
Some parameters to look for are:
 +
 
 +
*'''Operator''' = The telecom provider
 +
*'''Signal Quality''' = Shows the signal strength. The signal should be in the range of 10 - 31.
 +
 
 +
[[File:GSM Registered.PNG|thumb|left|500px|Gateway successfully registered to the GSM network]]
 +
<br style="clear:both;" />
 +
 
 +
If these parameters does not show, your gateway is not registered to the GSM network. Check that SIM card is properly inserted, and that the PIN code is correctly entered.
 +
 
 +
'''TIP''': Try the SIM card in a regular mobile phone.
 +
 
 +
===SIP settings===
 +
In the menu '''SIP Settings > Service Domain''', enter information for "Realm 1":
 +
 
 +
:*'''Active''' = ON
 +
:*'''User Name''' = Any text, used for Caller ID. This text will be shown in the display on incoming calls from the GSM network, together with the telephone number
 +
:*'''Proxy Server''' = IP address of the ICX or AlphaCom
 +
 
 +
[[Image:MV-370-SIP.PNG|left|thumb|500px|SIP Settings]]
 +
<br style="clear:both;" />
 +
 
 +
'''Status''' will show ''Not Registered''.
 +
 
 +
===Configure outgoing calls to the GSM network===
 +
 
 +
The configuration is done in '''Route''' > '''Lan To Mobile Settings'''.
 +
 
 +
====Two-stage dialing====
 +
This is the default-setting after a factory-reset.
 +
 
 +
The call progress is like this:
 +
 
 +
#The caller dials a prefix
 +
#A connection will be established to the GSM Gateway, and a second dial-tone is generated from the GSM-gateway
 +
#The caller dials the destination phone number
 +
 
 +
[[File:GSM mv370-two-stage-lantomobile.PNG|left|thumb|400px|Two-stage Lan to Mobile]]
 +
<br style="clear:both;" />
 +
 
 +
''Additional information:'' <br>
 +
As soon as the prefix is dialed, a voice connection is established between the ICX/AlphaCom and the GSM gateway. The GSM gateway will respond with the SIP message OK. Further dialing is signaled as DTMF signals to the GSM gateway.
 +
 
 +
====One-stage dialing====
 +
In this mode the outgoing number can either be configured directly in the GSM gateway or be sent to the GSM-gateway in the SIP invite from the ICX/AlphaCom.
 +
 
 +
''Phone number defined in the GSM gateway:''<br>
 +
In this mode the call is set up to the GSM gateway and the defined number is dialed automatically.
 +
[[File:GSM mv370-one-stage-in-mv370.PNG|left|thumb|400px|One-stage Lan to Mobile]]
 +
<br style="clear:both;" />
 +
 
 +
''Phone number received in SIP-INVITE from ICX/AlphaCom:''<br>
 +
In this mode the entire number is sent from the ICX/AlphaCom. 
 +
 
 +
'''N.B. If using MV-370 together with an ATLB card and analogue stations this is the recommended method.'''
 +
[[File:GSM mv370-one-stage-sipinvite.PNG|left|thumb|400px|One-stage lan to Mobile]]
 +
<br style="clear:both;" />
 +
 
 +
''Additional information:'' <br>
 +
When One-Stage Dialing is used, the GSM gateway will respond with the SIP message RINGING while the call is being established. The caller will hear the ringing tone generated by the ICX/AlphaCom. When the remote party answers the call, the GSM Gateway will send SIP message OK, and the voice communication will be established between the ICX/AlphaCom and the GSM gateway.
 +
 
 +
===Configure incoming calls from the GSM network===
 +
 
 +
There are two options:
 +
 
 +
*Two-stage dialing
 +
*Automatic dialing
 +
 
 +
====Two-stage dialing====
 +
With this setting there will be a second Dial-Tone presented on incoming calls from the GSM network. The user must dial the intercom number. The dialing can be terminated by '#', or alternatively one can wait for 5 seconds and the call will be established.
 +
 
 +
Select '''Route > Mobile to LAN Settings''', and set:<br>
 +
 
 +
:*'''CID''' = *
 +
:*'''URL''' = *
 +
 
 +
====Automatic dialing====
 +
With this setting incoming calls will automatically be connected to station 101 (or any other number you enter) in the ICX/AlphaCom.
 +
 
 +
 
 +
Select '''Route > Mobile to LAN Settings''', and set:<br>
 +
 
 +
:*'''CID''' = *
 +
:*'''URL''' = 101
 +
 
 +
 +
[[Image:MV-370-MobileToLAN.PNG|left|thumb|500px|Routing Mobile to LAN - Automatic dialing]]
 +
<br style="clear:both;" />
 +
 
 +
 
 +
===DTMF Input from outside line===
 +
During a conversation between a intercom station and a telephone, the telephone operator can activate an output (e.g. trigger a relay for door opening) in the ICX/AlphaCom by pressing a digit on the phone.
 +
 
 +
To enable digit actions from the telephone line during conversation, go to set '''SIP Settings''' > '''DTMF Setting''', and enable "SIP INFO":
 +
 
 +
[[File:GSM SIPINFO.PNG|left|thumb|500px|Set DTMF by 'SIP INFO']]
 +
<br style="clear:both;" />
 +
 
 +
==Configuration of ICX/AlphaCom==
 +
 
 +
Create a SIP trunk node in the ICX/AlphaCom. Follow the instructions in this article: [[SIP trunk node - configuration|SIP trunk node]]
 +
 
 +
===Two-stage dialing===
 +
This section is valid when using two-stage dialing for outgoing calls.
 +
 
 +
#To access the GSM Gateway from the ICX/AlphaCom, a directory number with feature 83/<SIP node> must be created in the Directory & Features window of AlphaPro.
 +
 
 +
[[Image:AlphaPro Create SIP AccessCode.jpg|left|thumb|500px|Example: Directory number "0" used for accessing the GSM Gateway]]
 +
<br style="clear:both;" />
 +
 
 +
:2. In order to automatically call a fixed telephone number from a DAK key, from a Call Button, or via Call Forwarding or AutoSearch, set "SIP dial delay" = 20 (2 sec.) in '''Exchange & System -> System -> VoIP''':
 +
 
 +
[[File:SIP Delay.PNG|left|thumb|500px|Set "SIP Dial Delay" when using automatic call to fixed phone number]]
 +
<br style="clear:both;" />
 +
 
 +
DAK key configuration:
 +
[[File:DAK Phone.PNG|left|thumb|500px|DAK 1 will dial 0 + 73456823]]
 +
<br style="clear:both;" />
 +
 
 +
===One-stage dialing===
 +
This section is valid when using One-stage dialing.
  
−
Select '''Route > Mobile to LAN Settings'''<br>
+
*To collect the phone number in ICX/AlphaCom, a directory number with feature 81/<SIP node> must be created in the Directory & Features window of AlphaPro. Parameter 2 defines the max amount of digits in the phone number.
−
Alternative 1 (default):
+
*If less digits than "max" is dialed, you can press M-key to send the number, or wait for timeout (3 sec by default).
−
* '''CID''' = *
 
−
* '''URL''' = *
 
−
This setting will give a second Dial-Tone on incoming calls to AlphaCom. The user must then dial the intercom number. The Mobile VoIP unit will connect the call 5 seconds after having received the last digit in the intercom number.
 
  
−
Alternative 2:  
+
[[Image:Alphapro Feature 81 one stage.jpg|left|thumb|600px|Example: Directory number "0" is used to start collecting numbers in ICX/AlphaCom. Parameter 2 defines the maximum amount of numbers]]
−
* '''CID''' = *
+
<br style="clear:both;" />
−
* '''URL''' = 101
 
−
With this setting incoming calls will automatically be connected to station 101 in the AlphaCom.
 
  
−
=== Mobile settings ===
+
==Features==
−
*Mobile > Settings > Mobile PIN Code: If the mobile needs to be unlocked by a pin code you must choose '''Enable''', and enter the pin code, and confirm the pin code
+
Outgoing calls from ICX/AlphaCom:
  
−
*Mobile > Status: Shows that the SIM card in in place, and that the Mobil VoIP unit is registered on the GSM network.
+
:*Selective: Prefix + phone number: Yes
 +
:*Dialed number shows in display: Yes
 +
:*Put call on hold and transfer: Yes
 +
:*Call to predefined phone number from DAK: Yes (Set "[[New fields (AlphaPro 10.27)|SIP dial delay]]" = 20)
 +
:*Call to predefined phone number from Substation: Yes (Set "[[New fields (AlphaPro 10.27)|SIP dial delay]]" = 20)
 +
:*Door Opening (6) from line: Yes (from firmware 669f in gateway)
 +
:*Cancel when remote phone hangs up: Yes
 +
:*Automatic cancel when remote phone is busy: Yes
 +
:*On-hook when intercom cancel the call: Yes
 +
:*Signal when dialing prefix and no lines are available : Busy tone (Camp on Busy)
 +
:*Call Forward (71) from intercom to external phone: Yes
 +
:*Forward Call Requests to phone: Yes
 +
:*Forward if phone do not answer: '''''No''''' (The gateway responds with "200 OK" immediately)
 +
:*Call to remote service requiring DTMF signaling (e.g. Call Center): Yes
 +
:*Call to remote service: DAK 0 transmit DTMF "*", DAK 1 = DTMF "#": Yes (from firmware 669f in gateway)
 +
:*Call from analogue phone (ATLB) to external phone: Yes
 +
:*Call from subscriber in remote AlphaNet node: Yes
 +
:*Call from SIP extension to external phone: Yes (X-Lite)
 +
:*Call from IP Substation: Yes
 +
:*Call from IP Master: Yes
 +
:*Access restriction for SIP Phones: Yes (OK with firmware 6.693t, was not OK with 6.690f)
 +
 +
 +
Incoming calls from GSM network:
  
−
=== SIP settings===
+
:*Two-step (selective) inward dialing - second dial tone: Yes
−
In the menu SIP Settings > Service Domain, enter information for "Realm 1":
+
:*Two-step (selective) inward dialing - voice prompt: No
−
* Active = ON
+
:*Automatic call to predefined station: Yes
−
*Display Name = Any text
+
:*Delayed automatic call to predefined station: No
−
*User Name = Access number to the gateway. This is the directory number you must dial on an intercom station to access the GSM gateway. The directory number must be programmed in the AlphaCom directory table with feature 83/<SIP node>.
+
:*Caller ID: Yes. The display will show <Phone number> + <User Name>, "User Name" is the text entered in [[#SIP_settings|SIP Settings]]. E.g. "73905391 (GSM)"
−
*Register Name = Access number to the gateway
+
:*Call to a remote node (AlphaNet) using Area Code or Global number: Yes
−
*Domain Server = IP address of the AlphaCom
+
:*Call to a SIP extension: Yes (X-Lite)
−
*Proxy Server = IP address of the AlphaCom
+
:*Make group call, with answer Meet Me (99): Yes
 +
:*M-key control from line: Yes (from firmware 669f in gateway)
 +
:*Door Opening (6) from line: Yes (from firmware 669f in gateway)
 +
:*Cancel call when on-hook from line: Yes
 +
:*Cancel call when cancel at intercom station: Yes
 +
:*Call to intercom station which is transferred (71) to an other station: Yes
 +
:*Put calls on hold and transfer (from intercom station): Yes
 +
:*Force calls from GSM network to be in Private: Yes (Set AlphaPro flag "[[New fields (AlphaPro 10.27)|Incoming calls from SIP in private ringing mode]]")
 +
:*Call to IP substation: Yes
 +
:*Call to  IP Masterstation: Yes
  
−
"Status" will show ''Registered'' when the gateway is registered at the SIP Registrar server in the AlphaCom.
+
<br>
  
−
Enable DTMF signalling by SIP INFO method:
+
==Related articles==
−
*SIP Settings > DTMF Setting: Enable "Send DTMF SIP Info"
 
  
−
=== Limitations===
+
*[[Send SMS messages from ICX-AlphaCom]]
−
Outgoing calls from AlphaCom:
+
*More documentation: https://www.zenitel.com/product/mv-370l-4g
−
* No DTMF tones can be sent from AlphaCom to the line during conversation (Nettbank kan ikke brukes).
 
−
* Digits during conversation (e.g. door opening, M-key) not possible from the phone
 
  
−
== Configuration of AlphaCom E ==
+
[[Category: ICX-AlphaCom - SIP Integration]]
−
The AlphaCom E needs to be configured with a [[SIP registrar node - configuration|SIP registrar node]]. Because the MV-370 needs to registrer to a SIP server, the AlphaCom must be equipped with [[Licenses#SIP_station_license|license for SIP phone]] (not SIP Trunk license!).
+
[[Category: AlphaCom - SIP Integration]]
 +
[[Category: 3rd party integration]]

Latest revision as of 14:14, 16 April 2024

AI.png
GSM Gateway MV-370

Alternative solution: IP Telephony Service (ICX-AlphaCom)

This article describes the setup of the GSM gateway MV-370 (Mobile VoIP) for communication with the ICX system or the AlphaCom.

The GSM Gateway must be equipped with a SIM card and registered to the GSM network as a regular mobile phone subscriber. Via the gateway calls can be made from the ICX or AlphaCom to the GSM network, as well as from the GSM network in to the ICX/AlphaCom.

GSM Gateway


It is also possible to send SMS messages from the ICX/AlphaCom via the GSM gateway.

Licenses

GSM Gateway Configuration

Important: If you have a SIM card with PIN code activated, DO NOT insert the SIM card yet.


Load Factory Default values

The GSM Gateway comes with default network parameters (factory default parameters). The default IP address is 192.168.0.100.

You can load factory network parameters and reset the username and password to its default settings (username: voip, password: 1234) by following these steps:

  1. Press and hold the button SW1 located at the bottom of the unit (you have to remove the lid) for about 7-8 seconds
  2. Wait for the "Mobile" and "LAN" leds to start blinking
Set default IP Address: Press SW1 for 7-8 seconds



  • The GSM Gateway will now get the IP address 192.168.0.100, subnet mask 255.255.255.0.

Accessing the gateway

  • Change the IP address of your PC to 192.168.0.99, subnet mask 255.255.255.0.
  • Connect the LAN port of the PC to the Ethernet port of the GSM Gateway.
  • Start your Web Browser and type 192.168.0.100 in the URL field.
  • Type in username voip and password 1234. (Case-sensitive!)
Accessing the gateway



  • The Home page of the Web Interface will appear:
Homepage of the GSM Gateway


Network settings

Change the network settings according to the network environment. Select Network > WAN Settings:

  • IP Type = Enable Fixed IP
  • IP = IP address of the Mobile VoIP unit
  • Mask = Network mask
  • Gateway = IP address of the network gateway
Network Settings



Mobile settings

Go to Mobile > Settings and define the following parameters:

  • SIP From = User/Tel (Not Reg)
  • Mobile PIN Code = ON. Code: Enter the PIN code for the SIM card. Confirmed: Enter the PIN code again.
Mobile settings



The SIM card can now be inserted. The gateway uses Standard (Mini) SIM card (15x25mm).

SIM card placement


After the SIM card is inserted, you can check that the gateway is successfully registered to the GSM network in Mobile > Status.

Some parameters to look for are:

  • Operator = The telecom provider
  • Signal Quality = Shows the signal strength. The signal should be in the range of 10 - 31.
Gateway successfully registered to the GSM network


If these parameters does not show, your gateway is not registered to the GSM network. Check that SIM card is properly inserted, and that the PIN code is correctly entered.

TIP: Try the SIM card in a regular mobile phone.

SIP settings

In the menu SIP Settings > Service Domain, enter information for "Realm 1":

  • Active = ON
  • User Name = Any text, used for Caller ID. This text will be shown in the display on incoming calls from the GSM network, together with the telephone number
  • Proxy Server = IP address of the ICX or AlphaCom
SIP Settings


Status will show Not Registered.

Configure outgoing calls to the GSM network

The configuration is done in Route > Lan To Mobile Settings.

Two-stage dialing

This is the default-setting after a factory-reset.

The call progress is like this:

  1. The caller dials a prefix
  2. A connection will be established to the GSM Gateway, and a second dial-tone is generated from the GSM-gateway
  3. The caller dials the destination phone number
Two-stage Lan to Mobile


Additional information:
As soon as the prefix is dialed, a voice connection is established between the ICX/AlphaCom and the GSM gateway. The GSM gateway will respond with the SIP message OK. Further dialing is signaled as DTMF signals to the GSM gateway.

One-stage dialing

In this mode the outgoing number can either be configured directly in the GSM gateway or be sent to the GSM-gateway in the SIP invite from the ICX/AlphaCom.

Phone number defined in the GSM gateway:
In this mode the call is set up to the GSM gateway and the defined number is dialed automatically.

One-stage Lan to Mobile


Phone number received in SIP-INVITE from ICX/AlphaCom:
In this mode the entire number is sent from the ICX/AlphaCom.

N.B. If using MV-370 together with an ATLB card and analogue stations this is the recommended method.

One-stage lan to Mobile


Additional information:
When One-Stage Dialing is used, the GSM gateway will respond with the SIP message RINGING while the call is being established. The caller will hear the ringing tone generated by the ICX/AlphaCom. When the remote party answers the call, the GSM Gateway will send SIP message OK, and the voice communication will be established between the ICX/AlphaCom and the GSM gateway.

Configure incoming calls from the GSM network

There are two options:

  • Two-stage dialing
  • Automatic dialing

Two-stage dialing

With this setting there will be a second Dial-Tone presented on incoming calls from the GSM network. The user must dial the intercom number. The dialing can be terminated by '#', or alternatively one can wait for 5 seconds and the call will be established.

Select Route > Mobile to LAN Settings, and set:

  • CID = *
  • URL = *

Automatic dialing

With this setting incoming calls will automatically be connected to station 101 (or any other number you enter) in the ICX/AlphaCom.


Select Route > Mobile to LAN Settings, and set:

  • CID = *
  • URL = 101


Routing Mobile to LAN - Automatic dialing



DTMF Input from outside line

During a conversation between a intercom station and a telephone, the telephone operator can activate an output (e.g. trigger a relay for door opening) in the ICX/AlphaCom by pressing a digit on the phone.

To enable digit actions from the telephone line during conversation, go to set SIP Settings > DTMF Setting, and enable "SIP INFO":

Set DTMF by 'SIP INFO'


Configuration of ICX/AlphaCom

Create a SIP trunk node in the ICX/AlphaCom. Follow the instructions in this article: SIP trunk node

Two-stage dialing

This section is valid when using two-stage dialing for outgoing calls.

  1. To access the GSM Gateway from the ICX/AlphaCom, a directory number with feature 83/<SIP node> must be created in the Directory & Features window of AlphaPro.
Example: Directory number "0" used for accessing the GSM Gateway


2. In order to automatically call a fixed telephone number from a DAK key, from a Call Button, or via Call Forwarding or AutoSearch, set "SIP dial delay" = 20 (2 sec.) in Exchange & System -> System -> VoIP:
Set "SIP Dial Delay" when using automatic call to fixed phone number


DAK key configuration:

DAK 1 will dial 0 + 73456823


One-stage dialing

This section is valid when using One-stage dialing.

  • To collect the phone number in ICX/AlphaCom, a directory number with feature 81/<SIP node> must be created in the Directory & Features window of AlphaPro. Parameter 2 defines the max amount of digits in the phone number.
  • If less digits than "max" is dialed, you can press M-key to send the number, or wait for timeout (3 sec by default).
Example: Directory number "0" is used to start collecting numbers in ICX/AlphaCom. Parameter 2 defines the maximum amount of numbers


Features

Outgoing calls from ICX/AlphaCom:

  • Selective: Prefix + phone number: Yes
  • Dialed number shows in display: Yes
  • Put call on hold and transfer: Yes
  • Call to predefined phone number from DAK: Yes (Set "SIP dial delay" = 20)
  • Call to predefined phone number from Substation: Yes (Set "SIP dial delay" = 20)
  • Door Opening (6) from line: Yes (from firmware 669f in gateway)
  • Cancel when remote phone hangs up: Yes
  • Automatic cancel when remote phone is busy: Yes
  • On-hook when intercom cancel the call: Yes
  • Signal when dialing prefix and no lines are available : Busy tone (Camp on Busy)
  • Call Forward (71) from intercom to external phone: Yes
  • Forward Call Requests to phone: Yes
  • Forward if phone do not answer: No (The gateway responds with "200 OK" immediately)
  • Call to remote service requiring DTMF signaling (e.g. Call Center): Yes
  • Call to remote service: DAK 0 transmit DTMF "*", DAK 1 = DTMF "#": Yes (from firmware 669f in gateway)
  • Call from analogue phone (ATLB) to external phone: Yes
  • Call from subscriber in remote AlphaNet node: Yes
  • Call from SIP extension to external phone: Yes (X-Lite)
  • Call from IP Substation: Yes
  • Call from IP Master: Yes
  • Access restriction for SIP Phones: Yes (OK with firmware 6.693t, was not OK with 6.690f)


Incoming calls from GSM network:

  • Two-step (selective) inward dialing - second dial tone: Yes
  • Two-step (selective) inward dialing - voice prompt: No
  • Automatic call to predefined station: Yes
  • Delayed automatic call to predefined station: No
  • Caller ID: Yes. The display will show <Phone number> + <User Name>, "User Name" is the text entered in SIP Settings. E.g. "73905391 (GSM)"
  • Call to a remote node (AlphaNet) using Area Code or Global number: Yes
  • Call to a SIP extension: Yes (X-Lite)
  • Make group call, with answer Meet Me (99): Yes
  • M-key control from line: Yes (from firmware 669f in gateway)
  • Door Opening (6) from line: Yes (from firmware 669f in gateway)
  • Cancel call when on-hook from line: Yes
  • Cancel call when cancel at intercom station: Yes
  • Call to intercom station which is transferred (71) to an other station: Yes
  • Put calls on hold and transfer (from intercom station): Yes
  • Force calls from GSM network to be in Private: Yes (Set AlphaPro flag "Incoming calls from SIP in private ringing mode")
  • Call to IP substation: Yes
  • Call to IP Masterstation: Yes


Related articles

Retrieved from "https://wiki.zenitel.com/w/index.php?title=GSM_gateway_(Mobile_VoIP)&oldid=236147"