Difference between revisions of "VSF-Fortitude8 7.4 Release Notes"
From Zenitel Wiki
(→New Features) |
(→Release info) |
||
| (6 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | Previous Release - [[VSF-Fortitude8 7.3 Release Notes]] | + | * Previous Release - [[VSF-Fortitude8 7.3 Release Notes]] |
| + | *Next Release - [[VSF-Fortitude8 7.5 Release Notes]] | ||
This document provides the release notes for VSF-Fortitude8 7.4 with incremental bug fix releases. The release notes for VSF-Fortitude8 7.4 describe new features, improvements and issues fixed after VSF-Fortitude8 7.3.3.1. | This document provides the release notes for VSF-Fortitude8 7.4 with incremental bug fix releases. The release notes for VSF-Fortitude8 7.4 describe new features, improvements and issues fixed after VSF-Fortitude8 7.3.3.1. | ||
| Line 5: | Line 6: | ||
==Release info== | ==Release info== | ||
'''Name:''' VSF-Fortitude8 <br> | '''Name:''' VSF-Fortitude8 <br> | ||
| − | '''Description:''' VSF-Fortitude8 is a firmware for | + | '''Description:''' VSF-Fortitude8 is a firmware for [[Zenitel Devices based on iMX8|Zenitel devices based on the IMX8 processor]]. |
| − | [[ | ||
The firmware is delivered in two different files: | The firmware is delivered in two different files: | ||
| Line 13: | Line 13: | ||
*vsff8-prod-7.4.3.x - Used in production- and recovery upgrades. | *vsff8-prod-7.4.3.x - Used in production- and recovery upgrades. | ||
| − | '''Version:''' 7. | + | '''Version:''' 7.4.3.0<br> |
| − | '''Date:''' | + | '''Date:''' 30.01.2023 <br> |
'''Status:''' General Availability<br> | '''Status:''' General Availability<br> | ||
| Line 24: | Line 24: | ||
<br> | <br> | ||
| − | == | + | ==Improvements== |
| − | ===MTN- | + | ===MTN-3867 Relay activation is now supported from NxWitness VMS=== |
| − | + | Added support for <onvifDevice:RelayOutputToken> tag to handle NxWitness implementation. | |
| + | ===MTN-3434 SNMP traps are now sent only on registration change state.=== | ||
| + | For example a trap will be sent when the devices goes from registered to unregistered (or vice versa), it was previously sent after each registration interval even if there were no changes to the state. | ||
<br> | <br> | ||
| − | == | + | ==Issues fixed== |
| − | === | + | === MTN-4008 Syncing is now properly mapped for Alphacom "Noise Reduction" configuration level 0 to 7=== |
| − | + | The new configuration "Moderate" was not mapped. New mapping: | |
| − | + | *0: ANC Disabled | |
| − | + | *1,2: ANC Enabled with Low Suppression | |
| − | + | *3,4: ANC Enabled with Moderate Suppression | |
| − | + | *5,6: ANC Enabled with High Suppression | |
| − | + | *7: ANC Enabled with Very High Suppression | |
| − | |||
| + | === MTN-3958 Changing VoIP port range adds 1000 ports to the start value=== | ||
| + | Max port number is 65535, if start value is higher than 64535, remaining ports are allocated. | ||
| − | + | === MTN-3952 Added support for disabling factory reset from call button or input=== | |
| − | + | If the checkbox is enabled it's not possible to factory reset the device via call button or input. | |
| − | === MTN- | ||
| − | |||
| − | === MTN- | + | === MTN-3951 Loudspeaker volume configuration now applied correctly after reboot=== |
| − | + | The loudspeaker level after boot was always similar to configuration, about +4dB. A configuration change up and down was needed to get back to configured audio level. The audio level shall now be applied as configured after boot. | |
| − | |||
| − | === MTN- | + | === MTN-3910 Uploaded certificates can now be deleted=== |
| − | + | The deletion of certificates uploaded in the device web was previously not possible. This is now fixed. | |
| − | === MTN- | + | === MTN-3906 Device now waits for the ONVIF subscription timer to run out before deleting subscription=== |
| − | + | Subscription timer for ONVIF messages was running out before the message timer. This is now fixed. | |
| − | === MTN- | + | === MTN-3896 Factory reset audio parameters now affects only Audio Settings page=== |
| − | + | Factory reset audio parameters doesn't affect VAD, Tone Test and DAVC settings, only settings which are configured on Audio Settings page. | |
<br> | <br> | ||
| Line 68: | Line 68: | ||
=== SUN-349 MJPEG stream shows green image in Avigilon=== | === SUN-349 MJPEG stream shows green image in Avigilon=== | ||
MJPEG stream shows green image in Avigilon, recommendation is to use H.264 for video integration instead. | MJPEG stream shows green image in Avigilon, recommendation is to use H.264 for video integration instead. | ||
| + | |||
| + | |||
| + | <br> | ||
| + | |||
[[Category: Release notes]] | [[Category: Release notes]] | ||
Latest revision as of 09:20, 21 June 2024
- Previous Release - VSF-Fortitude8 7.3 Release Notes
- Next Release - VSF-Fortitude8 7.5 Release Notes
This document provides the release notes for VSF-Fortitude8 7.4 with incremental bug fix releases. The release notes for VSF-Fortitude8 7.4 describe new features, improvements and issues fixed after VSF-Fortitude8 7.3.3.1.
Contents
- 1 Release info
- 2 VSF-FORTITUDE8 7.4.3.0
- 2.1 New Features
- 2.2 Improvements
- 2.3 Issues fixed
- 2.3.1 MTN-4008 Syncing is now properly mapped for Alphacom "Noise Reduction" configuration level 0 to 7
- 2.3.2 MTN-3958 Changing VoIP port range adds 1000 ports to the start value
- 2.3.3 MTN-3952 Added support for disabling factory reset from call button or input
- 2.3.4 MTN-3951 Loudspeaker volume configuration now applied correctly after reboot
- 2.3.5 MTN-3910 Uploaded certificates can now be deleted
- 2.3.6 MTN-3906 Device now waits for the ONVIF subscription timer to run out before deleting subscription
- 2.3.7 MTN-3896 Factory reset audio parameters now affects only Audio Settings page
- 2.4 Known Issues
Release info
Name: VSF-Fortitude8
Description: VSF-Fortitude8 is a firmware for Zenitel devices based on the IMX8 processor.
The firmware is delivered in two different files:
- vsff8-7.4.3.x - Used for standard in-field upgrades
- vsff8-prod-7.4.3.x - Used in production- and recovery upgrades.
Version: 7.4.3.0
Date: 30.01.2023
Status: General Availability
VSF-FORTITUDE8 7.4.3.0
New Features
MTN-3847 Option to disable registration in SIP mode added
A new option, No-Reg, has been added for Registration Method in Account Settings which will prevent registration towards a server. Device can operate in peer to peer mode.
Improvements
MTN-3867 Relay activation is now supported from NxWitness VMS
Added support for <onvifDevice:RelayOutputToken> tag to handle NxWitness implementation.
MTN-3434 SNMP traps are now sent only on registration change state.
For example a trap will be sent when the devices goes from registered to unregistered (or vice versa), it was previously sent after each registration interval even if there were no changes to the state.
Issues fixed
MTN-4008 Syncing is now properly mapped for Alphacom "Noise Reduction" configuration level 0 to 7
The new configuration "Moderate" was not mapped. New mapping:
- 0: ANC Disabled
- 1,2: ANC Enabled with Low Suppression
- 3,4: ANC Enabled with Moderate Suppression
- 5,6: ANC Enabled with High Suppression
- 7: ANC Enabled with Very High Suppression
MTN-3958 Changing VoIP port range adds 1000 ports to the start value
Max port number is 65535, if start value is higher than 64535, remaining ports are allocated.
MTN-3952 Added support for disabling factory reset from call button or input
If the checkbox is enabled it's not possible to factory reset the device via call button or input.
MTN-3951 Loudspeaker volume configuration now applied correctly after reboot
The loudspeaker level after boot was always similar to configuration, about +4dB. A configuration change up and down was needed to get back to configured audio level. The audio level shall now be applied as configured after boot.
MTN-3910 Uploaded certificates can now be deleted
The deletion of certificates uploaded in the device web was previously not possible. This is now fixed.
MTN-3906 Device now waits for the ONVIF subscription timer to run out before deleting subscription
Subscription timer for ONVIF messages was running out before the message timer. This is now fixed.
MTN-3896 Factory reset audio parameters now affects only Audio Settings page
Factory reset audio parameters doesn't affect VAD, Tone Test and DAVC settings, only settings which are configured on Audio Settings page.
Known Issues
SUN-476 HTTP MJPEG stream has color distortions when viewed in LenelS2 OnGuard
HTTP MJPEG stream has color distortions when viewed in LenelS2 OnGuard, recommendation is to use RTSP H.264 for video integration instead.
SUN-349 MJPEG stream shows green image in Avigilon
MJPEG stream shows green image in Avigilon, recommendation is to use H.264 for video integration instead.