Difference between revisions of "Automatic Volume Control (AVC)"
From Zenitel Wiki
| (7 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | {{ | + | {{AEIS}} |
| − | '''Automatic Volume Control (AVC)''' is a feature in the [[:Category:Intercoms and Devices|Zenitel IP devices]]. The AVC feature automatically adjusts the volume of the loudspeaker to compensate for ambient noise in an effort to make the audio signal better heard and understood above the noise. The AVC will perform better if the "Speaker Volume" is set to a fairly low level, as this will give the AVC more headroom for adjustments. The AVC feature works very well in combination with the [[Dynamic Range Compression (DRC)]] feature. | + | '''Automatic Volume Control (AVC)''' is a feature in the [[:Category:Intercoms and Devices|Zenitel IP devices]]. The microphone of the device is constantly measuring the ambient noise. The AVC feature automatically adjusts the volume of the loudspeaker to compensate for the ambient noise in an effort to make the audio signal better heard and understood above the noise. The AVC will perform better if the "Speaker Volume" is set to a fairly low level, as this will give the AVC more headroom for adjustments. The AVC feature works very well in combination with the [[Dynamic Range Compression (DRC)]] feature. |
Note that the volume is not adjusted while the speaker is playing audio. Adjustments are made in silent periods (min. 100 ms silence required). | Note that the volume is not adjusted while the speaker is playing audio. Adjustments are made in silent periods (min. 100 ms silence required). | ||
| Line 8: | Line 8: | ||
{{note|The web interface might look different in different firmware versions }} | {{note|The web interface might look different in different firmware versions }} | ||
<br> | <br> | ||
| − | |||
| − | |||
| − | [[File:AVC | + | === SIP mode === |
| + | Log in to the Zenitel IP device, and navigate to '''SIP Configuration''' > '''Audio Settings''', and enable "'''Automatic Volume Control (AVC)'''": | ||
| + | |||
| + | [[File:AVC SIP.png|thumb|left|700px|Enabling AVC on a device in SIP mode]] | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
<br> | <br> | ||
| − | === | + | === IC-Edge mode=== |
| − | Log in to the | + | Log in to the [[Edge Controller]], and navigate to '''Edge Controller''' > '''System Configuration''' > '''Call and Audio''', and enable "'''AVC'''": |
| − | [[File:AVC | + | [[File:AVC Enable Edge.png|thumb|left|700px|Enabling AVC in an IC-Edge system]] |
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| Line 42: | Line 43: | ||
*'''Enable AVC''': Check the box to enable automatic volume control. Volume is adjusted according to the ambient noise level. The AVC will perform better if the loudspeaker volume is set to a fairly low level, as this will give the AVC a more dynamic range for adjustments. Note that the AVC adjustment is disabled while the speaker is playing audio. Adjustments are made in silent periods (min. 100 ms silence required). | *'''Enable AVC''': Check the box to enable automatic volume control. Volume is adjusted according to the ambient noise level. The AVC will perform better if the loudspeaker volume is set to a fairly low level, as this will give the AVC a more dynamic range for adjustments. Note that the AVC adjustment is disabled while the speaker is playing audio. Adjustments are made in silent periods (min. 100 ms silence required). | ||
| − | *'''Debug in Display''': When enabled the station shows current volume level in the OLED display (applicable to TCIS-4, TCIx-5 and TCIx-6 stations) | + | *'''Debug in Display''': When enabled the station shows current volume level in the OLED display (applicable to TCIS-4, TCIx-5 and TCIx-6 stations). Very useful during testing or demo of the AVC feature. |
*'''AVC Advanced Settings''': Check to open for more advanced AVC settings | *'''AVC Advanced Settings''': Check to open for more advanced AVC settings | ||
** '''Lower Threshold''': Threshold level for the AVC to start working. Valid range: 30-80 dBA. Default is 55 dBA. | ** '''Lower Threshold''': Threshold level for the AVC to start working. Valid range: 30-80 dBA. Default is 55 dBA. | ||
** '''Upper Threshold''': Threshold level for the AVC to stop working. Valid range: 60-120 dBA. Default is 100 dBA. | ** '''Upper Threshold''': Threshold level for the AVC to stop working. Valid range: 60-120 dBA. Default is 100 dBA. | ||
| − | ** '''Attack Rate''': How quickly the AVC adjusts gain on raising ambient audio level. Range: 1..100 dBA/sec. Default is | + | ** '''Attack Rate''': How quickly the AVC adjusts gain on raising ambient audio level. Range: 1..100 dBA/sec. Default is 20 dBA/sec. |
** '''Decay Rate''': How quickly the AVC adjusts gain on falling ambient audio level. Range: 1..100 dBA/sec. Default is 10 dBA/sec. | ** '''Decay Rate''': How quickly the AVC adjusts gain on falling ambient audio level. Range: 1..100 dBA/sec. Default is 10 dBA/sec. | ||
** '''Hysteresis''': Hysteresis around previous set ambient audio level before doing adjustments. Range: 1..10 dBA/sec. Default is 3 dBA. | ** '''Hysteresis''': Hysteresis around previous set ambient audio level before doing adjustments. Range: 1..10 dBA/sec. Default is 3 dBA. | ||
| − | ** '''Far-End Lockout Time''': | + | ** '''Far-End Lockout Time''': The AVC adjustments are locked while the device is playing audio. When there is a pause in the audio (silence), adjustment commences after this lockout-time. Range: 1..100. Resolution is 100 ms. Default is "1" (= 100 ms). |
{{note|All audio settings can be reset to default values by selecting [[Factory Reset Audio Settings]]. }} | {{note|All audio settings can be reset to default values by selecting [[Factory Reset Audio Settings]]. }} | ||
| + | |||
| + | == Related articles == | ||
| + | * [[Distributed Automatic Volume Control (DAVC)]] | ||
| + | * [[Distributed Automatic Volume Control (DAVC) (SIP)]] | ||
[[Category: ICX-AlphaCom features]] | [[Category: ICX-AlphaCom features]] | ||
Latest revision as of 08:45, 27 June 2024
Automatic Volume Control (AVC) is a feature in the Zenitel IP devices. The microphone of the device is constantly measuring the ambient noise. The AVC feature automatically adjusts the volume of the loudspeaker to compensate for the ambient noise in an effort to make the audio signal better heard and understood above the noise. The AVC will perform better if the "Speaker Volume" is set to a fairly low level, as this will give the AVC more headroom for adjustments. The AVC feature works very well in combination with the Dynamic Range Compression (DRC) feature.
Note that the volume is not adjusted while the speaker is playing audio. Adjustments are made in silent periods (min. 100 ms silence required).
Contents
Enabling the AVC feature
How to enable the AVC feature depends on the mode of operation.
|
The web interface might look different in different firmware versions |
SIP mode
Log in to the Zenitel IP device, and navigate to SIP Configuration > Audio Settings, and enable "Automatic Volume Control (AVC)":
IC-Edge mode
Log in to the Edge Controller, and navigate to Edge Controller > System Configuration > Call and Audio, and enable "AVC":
ICX-AlphaCom mode
Log in to the Zenitel IP device, and navigate to Advanced ICX-AlphaCom > Audio Settings, and enable "Automatic Volume Control (AVC)":
AVC - Advanced configuration
To access the "AVC Advanced Settings" you first need to enable Advanced Configuration in the top right corner of the web interface.
Go to Audio Settings. Under Audio signal processing enable AVC Advanced Settings:
- Enable AVC: Check the box to enable automatic volume control. Volume is adjusted according to the ambient noise level. The AVC will perform better if the loudspeaker volume is set to a fairly low level, as this will give the AVC a more dynamic range for adjustments. Note that the AVC adjustment is disabled while the speaker is playing audio. Adjustments are made in silent periods (min. 100 ms silence required).
- Debug in Display: When enabled the station shows current volume level in the OLED display (applicable to TCIS-4, TCIx-5 and TCIx-6 stations). Very useful during testing or demo of the AVC feature.
- AVC Advanced Settings: Check to open for more advanced AVC settings
- Lower Threshold: Threshold level for the AVC to start working. Valid range: 30-80 dBA. Default is 55 dBA.
- Upper Threshold: Threshold level for the AVC to stop working. Valid range: 60-120 dBA. Default is 100 dBA.
- Attack Rate: How quickly the AVC adjusts gain on raising ambient audio level. Range: 1..100 dBA/sec. Default is 20 dBA/sec.
- Decay Rate: How quickly the AVC adjusts gain on falling ambient audio level. Range: 1..100 dBA/sec. Default is 10 dBA/sec.
- Hysteresis: Hysteresis around previous set ambient audio level before doing adjustments. Range: 1..10 dBA/sec. Default is 3 dBA.
- Far-End Lockout Time: The AVC adjustments are locked while the device is playing audio. When there is a pause in the audio (silence), adjustment commences after this lockout-time. Range: 1..100. Resolution is 100 ms. Default is "1" (= 100 ms).
|
|
All audio settings can be reset to default values by selecting Factory Reset Audio Settings. |