Difference between revisions of "IP Master Station Kit - 1008093000"

Revision as of 10:20, 3 August 2009

Features

Made for STENTOFON Critical Communication over IP (CCoIP)
Supports full keyboard including direct access keys (DAK) and dynamic keys
Supports handset and headset
Superb audio quality
0dB (600 Ohm) output to Public Address
Relay output for e.g. door lock control and tamper alarm input
Dual Ethernet ports for connection of other IP devices
Remote software upgrade, configuration and monitoring

Station Board Description

The IP Master Station Kit 100 8093 000 is delivered as a kit including board 8023, microphone and 2 x 6-pin plug-on screw terminals for local manufacturing of IP-CCoIP stations. The board is also used in STENTOFON standard IP flush mount master stations.

Connections

Station Board Connectors


P1	RJ45 LAN connector for 10/100 Mbit Ethernet connection.		P1, P2
The station can be powered from this connection if the line supports Power over Ethernet (PoE). The connector has two LEDs in front where the right (R) indicates Ethernet speed and the left (L) verifies Ethernet link and traffic. (L and R seen from the connector side).
P2	RJ45 connector for auxiliary equipment like IP camera, PC or a second IP station.
This port has not an individual IP address. It does not carry power for AUX equipment.

P3	6-pin plug-on screw terminal for external connections.		P3
	Pin 1/2	Connect to 1.5 W loudspeaker. Typical impedance: 8 Ω Recommended impedance: 6-25 Ω.
	Pin 3/4	Internal NO relay contact for door lock control etc.
	Pin 5/6	Connect 24 VDC for station power if PoE is not used. Pin 6 is positive.
P4	6-pin plug-on screw terminal for external connections.		P4
	Pin 1/4	Input 1
	Pin 2/4	Input 2
	Pin 3/4	Input 3
	5/6	Station Led for vall message info.

J4

J4: 18-pin ZIF-connector for keyboard.

The keyboard may have up to 10 dialling keys, M and C keys,10 DAK keys, 10 softkeys, volume up/down and light dim up/down keys connected in a matrix according to the drawing below.

J40: Optional keyboard connection.
J41: Optional DAK LED connection.

Connection to J40/41 can either be to a pin header or soldered directly to holes in the PCB.

J4 and J40 pin matrix

J4 and J40 pin1-9 Keyboard matrix

J4/10 - J41/1 DAK1 Green LED

J4/11 - J41/2 DAK1 Red LED

J4/12 - J41/3 DAK2 Green LED

J4/13 - J41/4 DAK2 Red LED

J4/14 - J41/5 DAK3 Green LED

J4/15 - J41/6 DAK3 Red LED

J4/16 - J41/7 DAK4 Green LED

J4/17 - J41/8 DAK4 Red LED

J4/18 - J41/9 Common +3.3V

The DAK keys and the DAK LEDs are programmed using IND commands in the Event Handler. DAK1-4 and Soft-key 1-4 are used in current master stations.
Privacy on/off is accomplished by pressing “C” for 3 sec. A P is shown in the display during Privacy.

J5: 20-pin ZIF-connector for LCD display.

Separate display panels are available as a kit of 5 units, 100 8099 000.

J6

J6: 6-pin Wire-to-Board Connector for I2C-interface.

Used for connection of DAK-modules.

Pin 1: Vcc

Pin 2: SDA (Data)

Pin 3: GND

Pin 4: GND

Pin 5: SCL (Clock)

Pin 6: Vcc

J7

J7: 3-pin header for connecting gooseneck microphone.

Pin 1: MIC+

Pin 2: MIC-