Touchless sensor (w/ backbox): Difference between revisions
From Zenitel Wiki
(Created page with "thumb|300px|right|Touchless sensor, item 2390020100 The '''Touchless sensor''' (item 2390020100) is a sensor for activation without...") |
No edit summary |
||
| (59 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
[[File:2390020100 touchless sensor 1.jpg|thumb| | [[File:2390020100 touchless sensor 1.jpg|thumb|200px|right|Touchless sensor, item 2390020100]] | ||
The '''Touchless sensor''' (item 2390020100) is | The '''Touchless sensor''' (item 2390020100) is an IR-sensor that connects to Zenitel IP stations, and is used to activate calls with gesture recognition instead of pressing the call button. | ||
The sensor button is powered by 5 volts. Most Zenitel IP stations has a built-in 5V output which can be used to power the sensor button. | |||
== Highlights == | == Highlights == | ||
<div style="float:right;"> <youtube width="350" height="210">3yYBW2ADsNI</youtube> </div> | |||
* Input Voltage: 5V | * Input Voltage: 5V | ||
* Available contacts: Normally Open & Normally Closed | * Available contacts: Normally Open & Normally Closed | ||
* Operating distance | * Sensor active time: 0,5 secs | ||
* | * Operating distance: 15cm | ||
* IP66 | |||
== Connections == | == Connections == | ||
Connections are made to the switch using the supplied 5 pin plug. <br> | Connections are made to the switch using the supplied 5 pin plug. <br> | ||
Correct orientation of the plug is ensured by the connector locating guides. | Correct orientation of the plug is ensured by the connector locating guides. | ||
=== Color code === | === Color code === | ||
* Red - +5 Volt supply | * Red - +5 Volt supply | ||
| Line 20: | Line 24: | ||
* Purple - Normally Open | * Purple - Normally Open | ||
== | == Typical Application == | ||
[[File:Touchless sensor | [[File:Touchless sensor wiring.png|thumb|500px|left|Touchless sensor - general wiring]] | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
== | == Use Case Examples == | ||
[[File:Touchless sensor wiring.png|thumb|500px|left|Touchless sensor - | Touchless sensor - wiring example: | ||
[[File:Touchless sensor wiring example.png|thumb|500px|left|Touchless sensor wired to Input 1 on a Turbine station]] | |||
<br style="clear:both;" /> | |||
=== Configuration on IC-Edge === | |||
*To configure the Input select '''Edge Controller''' > '''System Configuration''' > '''Direct Access Keys'''. <br> | |||
*Select '''Show/Hide Settings''' on the station you want to configure. | |||
*Configure the '''Input''' to '''Call To''', and enter the directory number to call when activated. | |||
[[File:TouchLess Inp1 Edge.PNG|thumb|700px|left|Input 1 configured to call number 13 when triggered]] | |||
<br style="clear:both;" /> | |||
More details can be found on [[Direct Access Key & Ringlist Settings (Edge)|Direct Access Key Settings]]. | |||
=== Configuration in ICX-AlphaCom === | |||
To configure the input to call a preconfigured number: | |||
# Select '''Users & Stations''' | |||
# Select the '''intercom station''' to which the touchless sensor is connected | |||
# Open the '''DAK''' window | |||
# Select the tab '''DAK 11-20''' | |||
# On DAK 11 (= input 1(*)) enter the '''directory number''' to call when the input is activated | |||
[[File:TouchLess ICX.png|thumb|700px|left|Input 1 configured to call number 13 when triggered]] | |||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
[[Category: | (*) Input 1 - 6 on Turbine stations are mapped to DAK 11 - 16. | ||
More information is found under [[Users & Stations (AlphaPro)#DAK|DAK programming]]. | |||
==Related Information== | |||
* [http://www.zenitel.com/product/touchless-sensor Additional Documentation on Zenitel.com] | |||
[[Category: Backboxes and accessories]] | |||
Latest revision as of 12:45, 18 February 2025
The Touchless sensor (item 2390020100) is an IR-sensor that connects to Zenitel IP stations, and is used to activate calls with gesture recognition instead of pressing the call button.
The sensor button is powered by 5 volts. Most Zenitel IP stations has a built-in 5V output which can be used to power the sensor button.
Highlights
- Input Voltage: 5V
- Available contacts: Normally Open & Normally Closed
- Sensor active time: 0,5 secs
- Operating distance: 15cm
- IP66
Connections
Connections are made to the switch using the supplied 5 pin plug.
Correct orientation of the plug is ensured by the connector locating guides.
Color code
- Red - +5 Volt supply
- Brown - 0 Volt supply
- Green - Normally Closed
- Blue - Common
- Purple - Normally Open
Typical Application
Use Case Examples
Touchless sensor - wiring example:
Configuration on IC-Edge
- To configure the Input select Edge Controller > System Configuration > Direct Access Keys.
- Select Show/Hide Settings on the station you want to configure.
- Configure the Input to Call To, and enter the directory number to call when activated.
More details can be found on Direct Access Key Settings.
Configuration in ICX-AlphaCom
To configure the input to call a preconfigured number:
- Select Users & Stations
- Select the intercom station to which the touchless sensor is connected
- Open the DAK window
- Select the tab DAK 11-20
- On DAK 11 (= input 1(*)) enter the directory number to call when the input is activated
(*) Input 1 - 6 on Turbine stations are mapped to DAK 11 - 16.
More information is found under DAK programming.