Difference between revisions of "IP-DECT base 300"
From Zenitel Wiki
(→IP-DECT Base 300 SIP Configuration) |
(→General Configuration) |
||
| Line 40: | Line 40: | ||
On the General Configuration page you define IP settings for the STENTOFON IP-DECT Base 300. | On the General Configuration page you define IP settings for the STENTOFON IP-DECT Base 300. | ||
| − | + | #Click Configuration. | |
| − | + | #In the IP Addr field, type in the IP address of the IP-DECT Base 300. | |
| − | + | #In the Netmask field, type in the network mask. | |
| − | + | #In the Gateway field, type in the IP address of the default gateway (optional). | |
| − | + | #Leave the rest to default settings. | |
| − | + | #Click Save. Answer yes on the following control question. | |
| − | + | #Click Reboot. You need to change your computers IP address to match your new address in the server in order to enter the configuration again. | |
| − | |||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
Revision as of 07:14, 31 May 2010
This article is quick setup guide describing the minimum requirements to setup the STENTOFON IP DECT Base 300 to work with the AlphaCom E using the SIP protocol.
Contents
Configuration of AlphaCom E
How to configure the AlphaCom E depends on the software version in the AMC-IP board.
AMC 10.56 and newer
- AlphaPro software 10.56. or newer is required for the configuration
- From the Users & Stations window in AlphaPro, select a user and enable the 'SIP station' flag
- Configure Directory number and Display text
- Select a supported codec for the SIP station to use
AMC 10.55 and earlier
The AlphaCom E needs to be configured with a SIP registrar node, and must be equipped with license for SIP stations.
Configuration of STENTOFON IP-DECT
Getting access to the embedded web server
Load factory default configuration on the IP-Dect Server by pressing the reset button through the hole at the rear with an unbend paper clip for 10 sec. Observe the front LED; when pressing the reset button the LED becomes steady red for about 5 seconds, it then starts to flash slowly. When releasing the reset button after 10 seconds, the LED starts to flash fast, colored red. It finally turns off (the server is rebooting).
Before the PC can access the IP Dect Server, the IP address of the PC must be changed to match the same subnet (for example 192.168.0.2). To access the embedded web server of the IP-Dect Server, start your internet browser (e.g. Internet Explorer) and in the address field enter 192.168.0.1. You will be prompted for a username and password.
Default (case senstive):
- Username: admin
- Password: kws300
The GENERAL STATUS page should now be displayed
General Configuration
All changes to fields marked with two stars need a reboot to take effect
On the General Configuration page you define IP settings for the STENTOFON IP-DECT Base 300.
- Click Configuration.
- In the IP Addr field, type in the IP address of the IP-DECT Base 300.
- In the Netmask field, type in the network mask.
- In the Gateway field, type in the IP address of the default gateway (optional).
- Leave the rest to default settings.
- Click Save. Answer yes on the following control question.
- Click Reboot. You need to change your computers IP address to match your new address in the server in order to enter the configuration again.
IP-DECT Base 300 SIP Configuration
All changes to fields marked with two stars need a reboot to take effect
In the Configuration/SIP page you define the general SIP settings.
1 Click Configuration, and then click SIP. 3 In the Default Domain field, type the name of the domain. For example Stentofon.com. 4 In the Proxy field, type in the IP address of your AlphaCom. 5 Leave the rest to default settings. 5 Click Save to save your SIP configuration data. 6 Go to the Administration page and click Reboot to make all the changes take effect.
Handset Registration and Subscription
This section provides information about handset registration and subscription. You must register and subscribe a handset before you can use it. When registering handsets you enter information about the handset settings (such as; the handset serial number (IPEI), name etc.) in the system database. When subscribing handsets you subscribe a registered handset to the system for usage. If the handset is not registered in the system database, subscription of the handset is not possible.
Registering IP-DECT Handsets
To register handsets you use the web based Administration Page of the STENTOFON IP-DECT Base 300.
Each handset in the wireless solution must be programmed with the serial number (IPEI) before it can operate. This serial number must be registered in the web based Administration Page of the IP-DECT Base. Serial numbers are a unique fingerprint of each handset. The serial number is programmed into the handset during the manufacturing process and cannot be changed by field personnel. The serial number can be found on a label beneath the battery or it can be viewed in the handsets display.
- For Rough and EX handsets: press *99984*V
- For Office handsets: press Menu, Status, Firmware version.
The Serial number consists of 12 digits and always starts with 00077
Log in to the IP DECT Base 300 and go to the Users page.
1 Click New. 2 In the IPEI field, type the IPEI number (serial number) of the handset. 3 In the Username/Extension field, type the Directory number configured in the AlphaCom. 4 In the Domain field, type the Domain used in your system, for example Stentofon.com 5 In the Displayname field, type the name to be displayed (caller ID) (optional). 6 Click Save to save the registration(s).
Leave the rest to default settings.
Subscribing Rough & EX Handsets
See Configuration_guide_for_STENTOFON_IP-DECT#Subscribing_Rough_and_EX_Handsets
Subscribing Office Handsets
See Configuration_guide_for_STENTOFON_IP-DECT#Subscribing_Office_Handsets