Difference between revisions of "IP Master Station Kit - 1008093000"
From Zenitel Wiki
(→Station Board Connectors) |
(→Station Board Connectors) |
||
| Line 173: | Line 173: | ||
'''S3''' 4-way DIP switch for future use.<br> | '''S3''' 4-way DIP switch for future use.<br> | ||
:Leave all in default OFF position. | :Leave all in default OFF position. | ||
| + | |||
| + | === IP Station Configuration === | ||
==Related Articles== | ==Related Articles== | ||
Revision as of 12:21, 3 August 2009
Contents
Features
- Made for STENTOFON Critical Communication over IP (CCoIP)
- Supports full keyboard including direct access keys (DAK) and dynamic keys
- Supports handset and headset
- Superb audio quality
- 0dB (600 Ohm) output to Public Address
- Relay output for e.g. door lock control and tamper alarm input
- Dual Ethernet ports for connection of other IP devices
- Remote software upgrade, configuration and monitoring
Station Board Description
The IP Master Station Kit 100 8093 000 is delivered as a kit including board 8023, microphone and 2 x 6-pin plug-on screw terminals for local manufacturing of IP-CCoIP stations. The board is also used in STENTOFON standard IP flush mount master stations.
Connections
Station Board Connectors
| P1 | RJ45 LAN connector for 10/100 Mbit Ethernet connection. | ||
| The station can be powered from this connection if the line supports Power over Ethernet (PoE). The connector has two LEDs in front where the right (R) indicates Ethernet speed and the left (L) verifies Ethernet link and traffic. (L and R seen from the connector side). | |||
| P2 | RJ45 connector for auxiliary equipment like IP camera, PC or a second IP station. | ||
| This port has not an individual IP address. It does not carry power for AUX equipment. | |||
| P3 | 6-pin plug-on screw terminal for external connections. | ||
| Pin 1/2 | Connect to 1.5 W loudspeaker. Typical impedance: 8 Ω Recommended impedance: 6-25 Ω. | ||
| Pin 3/4 | Internal NO relay contact for door lock control etc. | ||
| Pin 5/6 | Connect 24 VDC for station power if PoE is not used. Pin 6 is positive. | ||
| P4 | 6-pin plug-on screw terminal for external connections. | ||
| Pin 1/4 | Input 1 | ||
| Pin 2/4 | Input 2 | ||
| Pin 3/4 | Input 3 | ||
| 5/6 | Station Led for vall message info. | ||
J4: 18-pin ZIF-connector for keyboard.
- The keyboard may have up to 10 dialling keys, M and C keys,10 DAK keys, 10 softkeys, volume up/down and light dim up/down keys connected in a matrix according to the drawing below.
J40: Optional keyboard connection.
J41: Optional DAK LED connection.
Connection to J40/41 can either be to a pin header or soldered directly to holes in the PCB.
- J4 and J40 pin1-9 Keyboard matrix
- J4/10 - J41/1 DAK1 Green LED
- J4/11 - J41/2 DAK1 Red LED
- J4/12 - J41/3 DAK2 Green LED
- J4/13 - J41/4 DAK2 Red LED
- J4/14 - J41/5 DAK3 Green LED
- J4/15 - J41/6 DAK3 Red LED
- J4/16 - J41/7 DAK4 Green LED
- J4/17 - J41/8 DAK4 Red LED
- J4/18 - J41/9 Common +3.3V
The DAK keys and the DAK LEDs are programmed using IND commands in the Event Handler. DAK1-4 and Soft-key 1-4 are used in current master stations.
Privacy on/off is accomplished by pressing “C” for 3 sec. A P is shown in the display during Privacy.
J5: 20-pin ZIF-connector for LCD display.
- Separate display panels are available as a kit of 5 units, 100 8099 000.
J6: 6-pin Wire-to-Board Connector for I2C-interface.
- Used for connection of DAK-modules.
- Pin 1: Vcc
- Pin 2: SDA (Data)
- Pin 3: GND
- Pin 4: GND
- Pin 5: SCL (Clock)
- Pin 6: Vcc
J7: 3-pin header for connecting gooseneck microphone.
- Pin 1: MIC+
- Pin 2: MIC-
- Pin 3: GND
J8: Dual RJ11 for handset and headset.
- Handset can optionally be connected via J11, J12 and J13.
Handset:
- Pin 1: Mic+
- Pin 2: Spk+
- Pin 3: Spk- (0 V)
- Pin 4: Mic-
- Pin 5: Hook-switch (must be connected to pin 3 with a switch)
- Pin 6: PTT (May not be supported by SW)
Headset:
- Pin 7: Mic+
- Pin 8: Spk+
- Pin 9: Spk-
- Pin 10: Mic-
- Pin 11: PTT Ground
- Pin 12: PTT (May not be supported by SW)
J9: 6-pin header for connecting external amplifier.
- 12 V/5 W can be supplied to the external amplifier.
- Signal to amplifier is balanced 0dBm 600 ohm.
- Pin 1: +13 V: max. 500 mA to amplifier
- Pin 2: LSN: negative line
- Pin 3: LSP: positive line
- Pin 4: GND
- Pin 5: AMP_EN enable signal to amplifier
- Pin 6: AMP_ERR error signal from amplifier
J10 Internal microphone.
- Pin 1: MIC+
- Pin 2: MIC-
J11, 12 and 13 Pinheader for handset connection.
- Same as J8 pin 1 - 6.
- J11: Pin 1: Spk+
- J11: Pin 2: Spk-
- J12: Pin 1: Mic+
- J12: Pin 2: Mic-
- J13: Pin 1: OFFHOOK
- J13: Pin 2: GND
- J13: Pin 3: PTT
S1 Slide-switch to select internal mic. (Int) or gooseneck mic. (Ext).
S3 4-way DIP switch for future use.
- Leave all in default OFF position.