IND - Indicator control for CRMIV LEDs, buzzer etc.
From Zenitel Wiki
The IND (INDication) action is used for sending commands to a station. The commands are sent as display data. The following stations are currently using the IND command:
- CRM IV: Control the LED's in the DAK keys, the internal buzzer or relay, and the backlight of the display
- DualDisplay station: Control the video-state of the DAK-display
- Priscom station: Control the outputs used for lamps, cell light, call LED and spare output
The command syntax:
IND <station phys.no> <key no.> <LED no/buzzer> <Ind-type> [state]
Parameter description
Between the command parameters, there must always be a space.
Station Connect Operations
Message | CRM IV | DualDisplay | PrisCom |
---|---|---|---|
CALL_SETUP | CALL | 0x0008 | Sets up a coversation between two users |
CONN_REQUEST | CONN | 0x000A | Sets up a coversation between two users |
CONN_REFERENCE | 0x000B | Positive response from the exchange to CONN_REQUEST | |
CONN_REF_ACK | 0x000E | The external application acknowledges the CONN_REFERENCE | |
STATION_BUSY | 0x000D | Negative response to CONN_REQUEST | |
RESOURCE_BUSY | 0x003E | Negative response to CONN_REQUEST | |
NO_ACCESS | 0x003F | Negative response to CONN_REQUEST | |
STATION_DOWN | 0x000C | Negative response to CONN_REQUEST | |
DISCON_ST | 0x008E | Disconnect station from ongoing feature | |
DISC_REQ | 0x0011 | Conversation established with CONN_REQUEST: The external application disconnects a conversation. | |
DISC_REQ_ACK | 0x0012 | Conversation established with CONN_REQUEST: The AlphaCom acknowledges the DISC_REQ message | |
DISCONNECTED | 0x000F | Conversation established with CONN_REQUEST: Conversation was disconnected, e.g. the user pressed C-key | |
DISCONNECTED_ACK | 0x0010 | Conversation established with CONN_REQUEST: Acknowledge of the DISCONNECTED message | |
CALL_STATUS_BC | 0x0040 | Broadcast message telling the status of a call | |
CONN_STATUS_BC | 0x0041 | Broadcast message telling that a connection is established | |
DISCON_STATUS_BC | 0x0042 | Broadcast message telling that a connection is disconnected | |
PARK_INQ_BROKER | INQ | 0x0086 | Park station from conversation, enter Inquiry call state |
UNPARK | 0x0087 | Unpark station from Inquiry call state station, return to conversation | |
REQ_TRANSF_CALL | TRFC | 0x0088 | Transfer call in an Inquiry Call situation. |
PAR_RING | 0x0098 | Add a Parallel Ringer station to a call in ringing state |
station phys.no:
- 1-552 = The physical number of the station
key no.:
- 1-100 = The key number of the DAK-key
- 1023 = Buzzer
- 1024 = Display
- 1-100 = The key number of the DAK-key
Led no/buzzer:
- If the previous parameter was DAK-key (1 - 100):
- 1 = Red LED
- 2 = Green LED
- If the previous parameter was Buzzer (1023):
- 1 = Internal buzzer
- 2 = External buzzer (relay)
- If the previous parameter was Display (1024):
- 1 = Backlight
Ind-type:
- LEDs and display:
- 1 = continuous (low priority)
- 2 = slow flash (medium priority)
- 3 = fast flash (high priority)
- Buzzers:
- 1 = 1 bleep per 8 seconds (low priority)
- 2 = 1 bleep per 2 seconds (medium priority)
- 3 = 4 bleeps per second (high priority)
- 4 = continuous (alarm priority)
[state]:
- The brackets [ ] indicate that this command is optional. If nothing is entered in this field, the indication is switched on/off along with the event. By entering OFF, for example, you can set an indication to turn off when the event turns on.
- ON or OFF (capital letters)
Example
IND 2 23 2 3 ON – Station 2, key 23, turn green led, fast flashing, ON