Search results
Create the page "Low" on this wiki! See also the search results found.
Page title matches
- 3 KB (500 words) - 15:47, 25 October 2023
- 7 KB (1,035 words) - 14:15, 8 October 2019
Page text matches
- #REDIRECT [[Low level hardware analyze (not for beginners!)]]61 bytes (8 words) - 11:17, 5 February 2009
- ...s to mute the speaker of the device when the incoming audio signal is very low. ...ram]] channel), and there is not always voice present. In silent periods a low noise might be heard from the speaker. This is normally not noticeable, but2 KB (346 words) - 14:01, 7 November 2023
- | valign="top" |1 = continuous (low priority) <br> | valign="top" |1 = continuous (low priority) <br>6 KB (925 words) - 10:44, 22 December 2022
- ...coded in AlphaCom internal digital audio format (SigmaDelta) with a fairly low level, compared to the max theoretical amplitude of the audio format. A hea ...ternal format. The audio level on these connection will therefore be quite low.3 KB (521 words) - 14:46, 5 February 2018
- === MTN-435 User experience: Audio output level too low when in conversation with master stations=== Handset and Headset microphone level was too low according to standard voice level. The gain was increased gain with +10 dB3 KB (428 words) - 10:05, 21 June 2024
- ...vated by a high or low level. High level is used in AlphaCom system, while low level was used in the previous TouchLine generation of intercom system.2 KB (248 words) - 16:12, 23 June 2023
- * Noise Reduction levels 1 and 2 are translated to '''Low''' ...but is more likely to generate some artifacts on the speech. The setting "Low" or "Moderate" is normally the best option.3 KB (380 words) - 15:31, 25 October 2023
- 1=Low858 bytes (115 words) - 15:42, 3 October 2019
- * 1 = Low967 bytes (127 words) - 12:49, 30 June 2022
- *7931 = Filter 1 - Group Setup low priority1,016 bytes (137 words) - 09:37, 8 October 2019
- 1 = Low <br />1 KB (144 words) - 12:50, 30 June 2022
- 1 = Low (default)<br>1 KB (151 words) - 12:50, 30 June 2022
- * '''Low:''' Calls will always be in ''private ringing mode'', regardless of the pri1 KB (166 words) - 15:37, 20 May 2022
- * Sub-event 106: Billing: Low balance, abort around the corner. %1 = user1 KB (142 words) - 15:43, 19 February 2020
- [[File:2-2b solution3.PNG|left|thumb|500px|By setting Call Priority Setup = Low, the call from the Entrance will be forced to Private ringing mode, regardl [[File:2-2b solution4.PNG|left|thumb|500px|By setting Call Priority Setup = Low, the call from the SOS Point will be forced to Private ringing mode, regard3 KB (575 words) - 10:06, 30 June 2022
- * Comfort Noise type "low" to make Comfort Noise Generator (CNG)operation more natural in noisy envir ...||Low||||||align=left|Default is "Low". If hardware is linear enough, set "Low".13 KB (1,843 words) - 15:20, 25 October 2023
- $CAC U2 U0 U1 Cancel all calls in group 2 with low setup priority1 KB (183 words) - 15:42, 3 October 2019
- ...priority mechanism should apply to this multicast VoIP stream. Options are LOW, NORMAL, HIGH (default), and EMERGENCY. See more details below. Multicast paging uses 4 different priorities: LOW, NORMAL, HIGH, and EMERGENCY.6 KB (845 words) - 09:39, 1 October 2024
- [[File:1-4a solution2.PNG|left|thumb|500px|Set Call Setup Priority = Low]]2 KB (259 words) - 10:05, 30 June 2022
- ...se. The AVC will perform better if the "Speaker Volume" is set to a fairly low level, as this will give the AVC more headroom for adjustments. The AVC fea .... The AVC will perform better if the loudspeaker volume is set to a fairly low level, as this will give the AVC a more dynamic range for adjustments. Note4 KB (618 words) - 09:45, 27 June 2024