AUDIO_PATH_SETUP
|
0x8001
|
32769
|
AMC 06.00
|
AlphaNet: Set up audio path between a source node and a destination node (possibly via transit nodes). <br\>Audio path is needed for a number of exchange features. To speed up things, the feature setup message is included as “payload” of this message.
|
1 |
UINT1 |
Channel number. <br\>0 = request for channel.
|
2 |
UINT1 |
Priority<br\>0x00 ... 0x0F
|
3 |
UINT1 |
Starting node of audio path.
|
4 |
UINT1 |
Ending node of audio path.
|
5 |
UINT1 |
Backward local reference for next node
|
6 |
UINT1 |
Channel type. <br\>1 = Full duplex audio channel <br\>2 = IP full duplex audio channel. (field 7,8,9 added)
|
7 |
UINT4 |
Prev node Audio RTP IP address for next node (AMC 10.00)
|
8 |
UINT2 |
Prev node Audio RTP port number for next node (AMC 10.00)
|
9 |
BITMAP[1..32] |
Start node AudioCodecs supported. (AMC 10.00)<br\>Bit 1: G711<br\>Bit 2: G722<br\>Bit 3: 32Khz raw PCM <br\>Bit 4:
|
10 |
PAYLOAD |
End-to-end message. See below
|
Response:
|
AUDIO_LINK_OK <br\>AUDIO_LINK_NOT_AVAILABLE
|
<br\>PAYLOAD MESSAGE attached to AUDIO PATH SETUP and related messages:<br\>
|
1 |
UINT1 |
Protocol version:<br\>0 = AlphaCom basic functions
|
2 |
UINT1 |
Remote function:<br\>1 = Remote proxy station, digits will be dialed later. <br\>3 = Ordinary call identified by Bnumber parameter. <br\>5 = Call to waiting station identified by Bnumber parameter, used for answer calls. <br\>Support for remote functions 3 and 5 is acknowledged in AUDIO_PATH_OK with Bprotocol version set to 1 or higher.
|
3 |
UINT1 |
Exchange type:<br\>1 = AC <br\>2 = TL
|
4 |
UINT1 |
Station type:<br\>0 = Master <br\>1 = Sub <br\>2 = PNCI <br\>3 = CRM3/4 <br\>4 = Interguard <br\>5 = DualDisplay <br\>6 = Custom <br\>7 = SIP
|
5 |
UINT1 |
Display type <br\>1 = 2 line TL<br\>2 = CRM3/4
|
6 |
UINT1 |
Class of service
|
7 |
UINT1 |
Group call access level
|
8 |
UINT1 |
Call priority
|
9 |
BITMAP[1..16] |
Flags describing station and its configuration:<br\>bit 1: Handset_off<br\>bit 2: Mkey<br\>bit 3: Open/private <br\>bit 4: Voice help wanted<br\>bit 5: Allowed to page absent user<br\>bit 6: Name extension available (AMC 08.02)<br\>bit 7: Door opening available<br\>bit 8: Station duplex control (AMC 08.02)<br\>bit 9-15 not used. bit 1 and 2 always 0 in AMC 06.00
|
10 |
NET_OBJ_REF<br\>{ECL_STATION} |
A-station technical reference: node and physical number<br\>
|
11 |
NET_OBJ_REF<br\>{ECL_USER} |
A-station human reference: node and directory number.
|
12 |
TEXT16 |
Asubscriber text (name) for display.
|
13 |
UINT1 |
User Defined Properties (UDP) of Astation.<br\>Feature 1 = value 1, feature 8 = value 127, combinations allowed |
AMC 07.10
|
14 |
NET_OBJ_REF |
B number to be dialed in Bexchange.<br\>Only valid with remote functions 3 and 5<br\>If not used, this parameter should set to INVALID_NRF = 0x0F, or left out. |
AMC 07.10
|
Back to AlphaNet message list