Actions

Difference between revisions of "IND - Indicator control for CRMIV LEDs, buzzer etc."

From Zenitel Wiki

(Command syntax)
Line 128: Line 128:
 
The ''state'' parameter is optional. If nothing is entered in this field, the indication is switched on/off along with the event. By entering OFF, for example, you can set an indication to turn off when the event turns on.
 
The ''state'' parameter is optional. If nothing is entered in this field, the indication is switched on/off along with the event. By entering OFF, for example, you can set an indication to turn off when the event turns on.
  
Note on Turbine:
+
{{Note| '''Note on Turbine''': The output numbers depend on the AMC software version.
The output numbers to use depend on the AMC software version.
+
* ''AMC version 11.2.3.9 and earlier: Use IND numbers 1 - 7''
* AMC version 11.2.3.9 and earlier: Use IND numbers 1 - 7
+
* ''AMC version 11.2.3.10: Outputs cannot be controlled by IND command''
* AMC version 11.2.3.10: Outputs cannot be controlled by IND command
+
* ''AMC version 11.2.3.11 and later: Use IND numbers 11 - 17'' }}
* AMC version 11.2.3.11 and later: Use IND numbers 11 - 17
 
  
 
== Related articles ==
 
== Related articles ==

Revision as of 09:51, 12 April 2019

AlphaCom icon 300px.png

The IND (INDication) or GIND action are used in the Event Handler for sending commands to a station or a group of stations. The following stations are supporting the IND command:

  • IP Flush Master and CRM V: Control the LED's in the DAK keys
  • CRM IV: Control the LED's in the DAK keys, the internal buzzer or relay, and the backlight of the display
  • DualDisplay station: Control the video-state of the DAK-display
  • Priscom station: Control the outputs used for lamps, cell light, call LED and spare output
  • IP-ARIO: Control the Error LED and the Radio LED
  • IP Substation: Control relay and spare output
  • Turbine station: Control relay and the 6 additional outputs
  • ECPIR-3P and EBMDR-8 module


Command syntax

IND command:

IND <station phys.no> <output> <LED no/buzzer> <Ind-type> [state]


Example: On station 2, key 23, turn green led, fast flashing, ON

IND 2 23 2 3 ON


GIND command:

GIND <group ind> <output> <LED no/buzzer> <Ind-type> [state]


<group ind> is the AlphaCom group index number 1-250. (Not the group directory number)

There must be a space between the command parameters.

Parameter description:

Station/Parameter phys. number output LED no/buzzer IND-type [state]
CRM V and IP Flush Master (8024) 1 - 552 1-100 = DAK-key number 1 = Red LED

2 = Green LED

1 = continuous (low priority)

2 = slow flash (medium priority)
3 = fast flash (high priority)

ON or OFF
IP Substation (8022) 1 - 552 1 = Relay
2 = Spare output
Always "1"
1 = continuous (low priority)

2 = slow flash (medium priority)
3 = fast flash (high priority)

ON or OFF
Turbine station 1 - 552 17 = Relay
11-16 = Spare outputs
See note below!
Always "1"
1 = continuous (low priority)

2 = slow flash (medium priority)
3 = fast flash (high priority)

ON or OFF
ECPIR-3P 1 - 552 513 = Fault LED
Requires AMC 13.1.x.x
Always "1"
1 = continuous (low priority)

2 = slow flash (medium priority)
3 = fast flash (high priority)

ON or OFF
DualDisplay 1 - 552 1-100 = The DAK-key line Always "1" Video-state of the DAK-display:
0 = Normal
1 = Inverse
2 = Slow flash
3 = Fast flash
ON or OFF
IP-ARIO 1 - 552 1 = Radio LED
2 = Error LED
1 = Red LED (Radio and Error)

2 = Green LED (Radio LED only)

1 = continuous (low priority)

2 = slow flash (medium priority)
3 = fast flash (high priority)

ON or OFF
PrisCom 1 - 552 1 - 4 = Lamp outputs
5 - 6 = Spare outputs
7 = Relay (Cell light)
8 = Call LED
Always "1" 1 = continuous (low priority)

2 = slow flash (medium priority)
3 = fast flash (high priority)

ON or OFF
CRM IV 1 - 552 1-100 = DAK-key number
1023 = Buzzer
1024 = Display backlight
DAK-key:
1 = Red LED
2 = Green LED

Buzzer:

1 = Internal buzzer
2 = External buzzer (relay)

Display backlight:

1 = Backlight
DAK LED's:
1 = continuous (low priority)
2 = slow flash (medium priority)
3 = fast flash (high priority)

Buzzers:

1 = 1 bleep per 8 seconds (low priority)
2 = 1 bleep per 2 seconds (medium priority)
3 = 4 bleeps per second (high priority)
4 = continuous (alarm priority)

Display backlight:

1 = continuous
ON or OFF

The state parameter is optional. If nothing is entered in this field, the indication is switched on/off along with the event. By entering OFF, for example, you can set an indication to turn off when the event turns on.

Note icon Note on Turbine: The output numbers depend on the AMC software version.
  • AMC version 11.2.3.9 and earlier: Use IND numbers 1 - 7
  • AMC version 11.2.3.10: Outputs cannot be controlled by IND command
  • AMC version 11.2.3.11 and later: Use IND numbers 11 - 17


Related articles