Difference between revisions of "IP Master Station Kit - 1008093000"
From Zenitel Wiki
(→IP Station Configuration) |
(→IP Station Configuration) |
||
| Line 34: | Line 34: | ||
== IP Station Configuration == | == IP Station Configuration == | ||
| − | + | See article: [[IP Station Configuration]] | |
| − | |||
| − | See article: [[IP | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
==IP intercom station display menu== | ==IP intercom station display menu== | ||
Revision as of 15:35, 21 February 2012
Contents
Features
- Compatible with STENTOFON AlphaCom, STENTOFON Pulse and iPBXs (SIP)
- Master station PCB made for Critical Communication over IP (CCoIP®) in custom made station housings
- Superb audio technology – gives loud-speaking hands-free duplex communication from any location in the room
- Remote software upgrade, configuration and monitoring
- Integrated data switch with advanced networking and security functions
- Powered from the IP network cable using Power over Ethernet (PoE)
- Supports large high contrast display with white backlight for excellent readability
- Supports handset and headset
- Supports full keyboard
- Supports digital inputs and output via built-in relay
- Supports external audio amplifiers
Station Board Description
The IP kit supports open standards and is compatible with STENTOFON AlphaCom, STENTOFON Pulse and iPBXs using SIP technology. When working in AlphaCom mode, the IP kit supports special services only available using the STENTOFON CCoIP protocol, AlphaCom server. Examples of services are emergency broadcast with volume override, CCTV integration, call priority, and AlphaNet multisite networking and STENTOFON event scripting.
The STENTOFON IP master Station Kit features the electronics board as used in STENTOFON IP master stations. It is designed to produce custom IP stations to the highest specifications and for use in the harshest of environments.
The IP master Station Kit provides upto 1.5 W audio output. If even higher audio output is required an external power amplifier can be used. As a special function, the PCB can extract power from the Ethernet’s
PoE circuit and give upto 6 W power to external units. This means that the P cb can power an external
power amplifier using its own PoE.
The PCB has one relay output and three logical inputs. These outputs can for instance be used to control and open a door or PA interface. The operation of the outputs and inputs are programmable and controlled
by the AlphaCom XE exchange. The IP station PCB has an integrated managed data switch providing advanced networking and security features. The integrated switch provides support for:
- Protection from unwanted access
- Quality of Service (QoS) by managing data traffic
- Increased system availability through redundant LAN infrastructure
- Cost efficient installation by providing shared network connections
To provide maximum availability the station comes with advanced supervision functions. The station line test will detect if there is any faults in the network or station electronics. In addition the station supports tone test, testing the complete transmission path including microphone and speaker. The status of the stations is reported to AlphaWeb as well as to 3rd party management systems using SNMP, SysLog or OPC.
Station Board Connectors
See article: IP Station Board Connections and Indications
IP Station Configuration
See article: IP Station Configuration
When the IP station is not connected to an AlphaCom exchange, a local menu is available in the station display. This menu can be used to configure the IP Station. The structure of the menu is listed below:
Station info
| MAC adr: | 0013cb000000 |
| St IP: | 169.254.1.100 |
| AMC IP: | 169.254.1.5 |
| SW ver: | 01.07 (per. 2009) |
IP settings
| < > | DHCP | (input) |
| <*> | STATIC | (input) |
| IPaddr | 169.254.1.100 | (input) |
| IPmask: | 255.255.0.0 | (input) |
| IPgw: | 169.254.1.1 | (input) |
AlphaCom IP
| AMC IP: | 169.254.1.5 | (input) |
Load defaults
| Press to set. (Station will restart.) | (input) |
Restart
| Press to restart | (input) |
- To enter the menu, press Setup and use code 1851 for sw v.1.07 (code 1234 for sw v.105).
- When editing IP-addresses, use the M-key to insert ”.” (dot).
- Restart the station to apply new settings.
AlphaWeb and AlphaPro
IP intercom stations communicate with the AlphaCom E exchange via TCP port 50001. This port needs to be configured and enabled in System Configuration > Filters in AlphaWeb.
In AlphaPro, tick the IP Station box and enter the IP Station MAC-address. Also, from the station type drop-down menu, choose the correct Station Type (CRM IV, Dual Display Station, OR Station).
Indication LEDs
See article: IP Station Board Connections and Indications
Reset to factory settings
See article: IP Station Restore Factory Defaults
Dimensions
See article: IP Stations Dimensions and Mounting Instructions