Difference between revisions of "Turbine Compact Board Connectors"
From Zenitel Wiki
| (24 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
| − | =Main PCB= | + | {{AEIPS}} |
| − | ==Front== | + | ==Main PCB (A100C08121) == |
| + | ===Front=== | ||
[[File:TCIS Connections 3.PNG|500px]] | [[File:TCIS Connections 3.PNG|500px]] | ||
| Line 10: | Line 11: | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| − | + | '''P2''' 5-pin plug-on terminal for relay and external power | |
| − | |||
| − | '''P2''' | ||
[[File:TCIS Connections 5.PNG|thumb|500px|left]] | [[File:TCIS Connections 5.PNG|thumb|500px|left]] | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| − | :Pin 1/2 24 VDC for external secondary power if PoE is not used. Pin 1 is positive. | + | :Pin 1/2: 24 VDC for external secondary power if PoE is not used. Pin 1 is positive. |
| − | :Pin 3 | + | :Pin 3: COM relay (Common) |
| − | :Pin 4 | + | :Pin 4: NO relay (Normally Open) |
| − | :Pin 5 | + | :Pin 5: NC relay (Normally Closed) |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | * Relay switching capacity: Max. 60 watt (Max voltage: 250VAC/220VDC. Max current: 2A) | |
| + | * Connectable conductors: 0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm². | ||
| − | '''P3''' 10-pin plug-on terminal for | + | '''P3''' 10-pin plug-on terminal for I/O's and Audio Line Out |
[[File:TCIS Connections 6.PNG|thumb|300px|left]] | [[File:TCIS Connections 6.PNG|thumb|300px|left]] | ||
| Line 48: | Line 37: | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| + | * Connectable conductors: 0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm². | ||
| + | |||
| + | '''P4''' Loudspeaker & Electret microphone | ||
| + | [[File:TCIS Connections 7.PNG|thumb|500px|left]] | ||
| + | <br style="clear:both;" /> | ||
| + | :Pin 1: Speaker output + | ||
| + | :Pin 2: Speaker output - | ||
| + | :Pin 3: Electret Microphone + | ||
| + | :Pin 4: Electret Microphone - | ||
| + | |||
| + | * Connectable conductors: 0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm². | ||
| + | * Recommended loudspeaker impedance: 8 ohms | ||
| + | |||
| + | {{Note | To enable the electret microphone input when using a [[TKIS-2]], the "'''Product Model And Accessory'''" must be set to "'''Kit'''" under [[Main Settings (IP Stations)|Station Main > Main Settings]] in the web interface of the device.}} | ||
| + | |||
| + | |||
| − | ==Output Connectors + 1 relay== | + | ===Output Connectors + 1 relay=== |
[[File:TCIS Connections 12.PNG|500px|Connecting to the onboard relay. Extra LED controlled by output 1]] | [[File:TCIS Connections 12.PNG|500px|Connecting to the onboard relay. Extra LED controlled by output 1]] | ||
| Line 60: | Line 65: | ||
The 5,3V output can deliver 200mA current maximum | The 5,3V output can deliver 200mA current maximum | ||
| − | See also [[ | + | See also [[Adding additional relay(s) to a Zenitel IP Device]] |
| − | ==Rear== | + | ===Rear=== |
[[File:TCIS Connections 8.PNG|500px]] | [[File:TCIS Connections 8.PNG|500px]] | ||
| Line 81: | Line 86: | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| − | =Front Board= | + | ==Front Board (A100C08129)== |
| − | Note | + | {{Note | Not applicable to TKIS-2 and TMIS-x}} |
| − | ==Front== | + | ===Front=== |
[[File:TCIS Connections 10.PNG|500px]] | [[File:TCIS Connections 10.PNG|500px]] | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| − | ==Rear== | + | ===Rear=== |
[[File:TCIS Connections 11.PNG|500px]] | [[File:TCIS Connections 11.PNG|500px]] | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| − | [[Category: Turbine]] | + | [[Category: Turbine Connections]] |
Latest revision as of 16:22, 23 June 2023
Contents
Main PCB (A100C08121)
Front
P1 RJ45 PoE port for 10/100 Mbit Ethernet connection.
- The station can be powered from this port if the line supports Power over Ethernet (PoE).
P2 5-pin plug-on terminal for relay and external power
- Pin 1/2: 24 VDC for external secondary power if PoE is not used. Pin 1 is positive.
- Pin 3: COM relay (Common)
- Pin 4: NO relay (Normally Open)
- Pin 5: NC relay (Normally Closed)
- Relay switching capacity: Max. 60 watt (Max voltage: 250VAC/220VDC. Max current: 2A)
- Connectable conductors: 0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm².
P3 10-pin plug-on terminal for I/O's and Audio Line Out
- Pin 1 5.3V (max. 200mA current)
- Pin 2 GND
- Pin 3 Button Input or LED Driver
- Pin 4 Button Input or LED Driver
- Pin 5 Button Input or LED Driver
- Pin 6 Button Input or LED Driver
- Pin 7 Button Input or LED Driver
- Pin 8 Button Input or LED Driver
- Pin 9 600 ohm balanced line out +
- Pin 10 600 ohm balanced line out -
- Connectable conductors: 0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm².
P4 Loudspeaker & Electret microphone
- Pin 1: Speaker output +
- Pin 2: Speaker output -
- Pin 3: Electret Microphone +
- Pin 4: Electret Microphone -
- Connectable conductors: 0.20 - 1.5 mm² (IEC) / 24 - 16 AWG (UL). Use of ferrules is recommended. Max cable size is then 0.75 mm².
- Recommended loudspeaker impedance: 8 ohms
|
To enable the electret microphone input when using a TKIS-2, the "Product Model And Accessory" must be set to "Kit" under Station Main > Main Settings in the web interface of the device. |
Output Connectors + 1 relay
The extra relay for any of the 6 I/O pins is connected as shown:
Most general purpose P-Channel MOSFET's should work. Recommended example: BSS84
The 5,3V output can deliver 200mA current maximum
See also Adding additional relay(s) to a Zenitel IP Device
Rear
J6 10-pin terminal for digital MEMS Microphone
- Pin 1 Left mic select (Vdd)
- Pin 2 Right mic select (GND)
- Pin 3 Data
- Pin 4 Data
- Pin 5 Vdd 3.3V
- Pin 6 Vdd 3.3V
- Pin 7 CLK
- Pin 8 CLK
- Pin 9 GND
- Pin 10 GND
Front Board (A100C08129)
|
|
Not applicable to TKIS-2 and TMIS-x |
Front
Rear
