Latest revision as of 12:55, 24 May 2023

Previous Release - VSF-Fortitude6 7.3 Release Notes
Next Release - VSF-Fortitude6 7.5 Release Notes

This document provides the release notes for VSF-Fortitude6 7.4 with incremental bug fix releases. The release notes for VSF-Fortitude6 7.4 describe new features, improvements and issues fixed after VSF-Fortitude6 7.3.3.0.

Release info

Name: VSF-Fortitude6
Description: VSF-Fortitude6 is a firmware for IP Desk Master -V2, IP Desk Master -V2-P, IP Flush Master -V2 and IP-CROR.

The firmware is delivered in two different files:

vsff6-7.4.3.x - Used for standard in-field upgrades
vsff6-prod-7.4.3.x - Used in production- and recovery upgrades.

Version: 7.4.3.0
Date: 30.01.2023
Status: General Availability

VSF-FORTITUDE6 7.4.3.0

New Features

MTN-3847 Option to disable registration in SIP mode added A new option, No-Reg, has been added in Registration Method > Account Settings. This will prevent registration towards a SIP server. Device can then operate in peer to peer mode.

Improvements

MTN-3867 Relay activation is now supported from NxWitness VMS

Added support for <onvifDevice:RelayOutputToken> tag to handle NxWitness implementation.

MTN-3434 SNMP traps are now sent only on registration change state.

For example a trap will be sent when the devices goes from registered to unregistered (or vice versa), it was previously sent after each registration interval even if there were no changes to the state.

Fixed Issues

MTN-4008 Syncing is now properly mapped for Alphacom "Noise Reduction" configuration level 0 to 7

The new configuration "Moderate" was not mapped. New mapping:

0: ANC Disabled
1,2: ANC Enabled with Low Suppression
3,4: ANC Enabled with Moderate Suppression
5,6: ANC Enabled with High Suppression
7: ANC Enabled with Very High Suppression

MTN-3958 Changing VoIP port range adds 1000 ports to the start value

Max port number is 65535, if start value is higher than 64535, remaining ports are allocated.

MTN-3910 Uploaded certificates can now be deleted

The deletion of certificates uploaded in the device web was previously not possible. This is now fixed.

MTN-3906 Device now waits for the ONVIF subscription timer to run out before deleting subscription

Subscription timer for ONVIF messages was running out before the message timer. This is now fixed.

MTN-3896 Factory reset audio parameters now affects only Audio Settings page

Factory reset audio parameters doesn't affect VAD, Tone Test and DAVC settings, only settings which are configured on Audio Settings page.

MTN-3884 Fixed sending of unnecessary DHCP requests

Correct configuration is applied to interface and unnecessary DHCP requests will not be sent anymore.

@@ Line 1: / Line 1: @@
 * Previous Release - [[VSF-Fortitude6 7.3 Release Notes]]
+* Next Release - [[VSF-Fortitude6 7.5 Release Notes]]
 This document provides the release notes for VSF-Fortitude6 7.4 with incremental bug fix releases. The release notes for VSF-Fortitude6 7.4 describe new features, improvements and issues fixed after VSF-Fortitude6 7.3.3.0.
@@ Line 22: / Line 23: @@
 ==New Features ==
 MTN-3847 Option to disable registration in SIP mode added
-A new option, '''No-Reg''', has been added for '''Registration Method''' > '''Account Settings''' which will prevent registration towards a server. Device can operate in peer to peer mode.
+A new option, '''No-Reg''', has been added in '''Registration Method''' > '''Account Settings'''. This will prevent registration towards a SIP server. Device can then operate in peer to peer mode.
+<br>
+== Improvements ==
+===MTN-3867 Relay activation is now supported from NxWitness VMS===
+Added support for <onvifDevice:RelayOutputToken> tag to handle NxWitness implementation.
+===MTN-3434 SNMP traps are now sent only on registration change state.===
+For example a trap will be sent when the devices goes from registered to unregistered (or vice versa), it was previously sent after each registration interval even if there were no changes to the state.
+<br>
 ==Fixed Issues==
-=== MTN-3905 Triggering relay via ONVIF in ICX-AlphaCom mode fixed===
+=== MTN-4008 Syncing is now properly mapped for Alphacom "Noise Reduction" configuration level 0 to 7===
-Fixed an issue which prevented relay being triggered over ONVIF if station is in ICX-AlphaCom mode
+The new configuration "Moderate" was not mapped. New mapping:
+*0: ANC Disabled
+*1,2: ANC Enabled with Low Suppression
+*3,4: ANC Enabled with Moderate Suppression
+*5,6: ANC Enabled with High Suppression
+*7: ANC Enabled with Very High Suppression
+=== MTN-3958 Changing VoIP port range adds 1000 ports to the start value===
+Max port number is 65535, if start value is higher than 64535, remaining ports are allocated.
+=== MTN-3910 Uploaded certificates can now be deleted===
+The deletion of certificates uploaded in the device web was previously not possible. This is now fixed.
+=== MTN-3906 Device now waits for the ONVIF subscription timer to run out before deleting subscription===
+Subscription timer for ONVIF messages was running out before the message timer. This is now fixed.
+=== MTN-3896 Factory reset audio parameters now affects only Audio Settings page===
+Factory reset audio parameters doesn't affect VAD, Tone Test and DAVC settings, only settings which are configured on Audio Settings page.
-=== MTN-3860 ONVIF issue with AMAG Symmetry fixed===
+=== MTN-3884 Fixed sending of unnecessary DHCP requests===
-Fixed an issue which prevented station from being added to AMAG Symmetry.
+Correct configuration is applied to interface and unnecessary DHCP requests will not be sent anymore.
 [[Category: Release notes]]

Difference between revisions of "VSF-Fortitude6 7.4 Release Notes"

From Zenitel Wiki