Actions

Difference between revisions of "Toggle Applications"

From Zenitel Wiki
(→‎Volume adjustment)
 
(6 intermediate revisions by 2 users not shown)
Line 1: Line 1:
−
{{A}}
+
{{AI}}
 
This article describes different applications where the common scenario is to toggle a feature on/off using just a DAK key (or station input). Some features have options that gives additional opportunities.
 
This article describes different applications where the common scenario is to toggle a feature on/off using just a DAK key (or station input). Some features have options that gives additional opportunities.
  
Line 5: Line 5:
  
 
==Conversation==
 
==Conversation==
 +
 +
{{note|As from AlphaCom v. 13 a call can be toggled on/off from a DAK key by setting the flag [[Users_%26_Stations_(AlphaPro)#Station_Type_tab|Idle DAK during conv. cancel ongoing call]]. No need to program any events}}
 +
 
Toggle between '''Call''' and '''Cancel''': pressing DAK key 1 sets up a call to station 101. Second press cancels the call. A second event must be created to handle the scenario where 101 initiates the call , or ends the call.
 
Toggle between '''Call''' and '''Cancel''': pressing DAK key 1 sets up a call to station 101. Second press cancels the call. A second event must be created to handle the scenario where 101 initiates the call , or ends the call.
  
Line 10: Line 13:
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
−
Action commands:
+
{{Code2|
−
  ''IF %udd(%1.phy)''
+
  IF %udd(%1.phy)
−
  ''$C L%1.dir''
+
  $C L%1.dir
−
  ''WUDD %1.phy 0''
+
  WUDD %1.phy 0
−
  ''STOP''
+
  STOP
−
  ''ENDIF''
+
  ENDIF
−
  ''$CALL L%1.dir L101''
+
  $CALL L%1.dir L101
−
  ''WUDD %1.phy 1''
+
  WUDD %1.phy 1
−
<br/>
+
}}
  
 
[[File:Toggle Applications 8.PNG|thumb|left|500px|Adjust UDD if call initiated or ended from the other station]]
 
[[File:Toggle Applications 8.PNG|thumb|left|500px|Adjust UDD if call initiated or ended from the other station]]
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
−
Action command:
+
{{Code2|
−
  ''WUDD %1.phy %chg(1,0)''
+
  WUDD %1.phy %chg(1,0)
−
<br/>
+
}}
  
 
The same DAK can also answer an '''incoming call in private mode'''. Then the following event must be added:
 
The same DAK can also answer an '''incoming call in private mode'''. Then the following event must be added:
Line 33: Line 36:
  
 
Add some commands to the top of the initial DAK as RCI event, making it look like this:
 
Add some commands to the top of the initial DAK as RCI event, making it look like this:
−
  ''IF %op(%udd(%1.phy),=,2)''
+
{{Code2|
−
  ''$M L%1.dir''
+
  IF %op(%udd(%1.phy),<nowiki>=</nowiki>,2)
−
  ''pause''
+
  $M L%1.dir
−
  ''$MREL L%1.dir''
+
  pause
−
  ''WUDD %1.phy 1''
+
  $MREL L%1.dir
−
  ''STOP''
+
  WUDD %1.phy 1
−
  ''ENDIF''
+
  STOP
−
  ''IF %udd(%1.phy)''
+
  ENDIF
−
  ''$C L%1.dir''
+
  IF %udd(%1.phy)
−
  ''WUDD %1.phy 0''
+
  $C L%1.dir
−
  ''STOP''
+
  WUDD %1.phy 0
−
  ''ENDIF''
+
  STOP
−
  ''$CALL L%1.dir L101''
+
  ENDIF
−
  ''WUDD %1.phy 1''
+
  $CALL L%1.dir L101
−
<br/>
+
  WUDD %1.phy 1
 +
}}
  
 
For more details see [[$CALL]], [[$C]], [[$M]], [[$MREL]] and [[PAUSE|pause]]
 
For more details see [[$CALL]], [[$C]], [[$M]], [[$MREL]] and [[PAUSE|pause]]
Line 57: Line 61:
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
−
Action commands:
+
{{Code2|
−
  ''IF %udd(%1.phy)''
+
  IF %udd(%1.phy)
−
  ''$CANM L%1.dir L101''
+
  $CANM L%1.dir L101
−
  ''WUDD %1.phy 0''
+
  WUDD %1.phy 0
−
  ''STOP''
+
  STOP
−
  ''ENDIF''
+
  ENDIF
−
  ''$SM L%1.dir L101''
+
  $SM L%1.dir L101
−
  ''WUDD %1.phy 1''
+
  WUDD %1.phy 1
−
<br/>
+
}}
  
 
[[File:Toggle CR 2.PNG|thumb|left|500px|Reset UDD when station is no longer in Call Request mode (i.e. the Call Request is for any reason removed)]]
 
[[File:Toggle CR 2.PNG|thumb|left|500px|Reset UDD when station is no longer in Call Request mode (i.e. the Call Request is for any reason removed)]]
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
−
Action commands:
+
{{Code2|
−
  ''WUDD %2.phy 0''
+
  WUDD %2.phy 0
−
<br/>
+
}}
  
 
To add the possibility to answer incoming calls in private using the same DAK, see the [[Toggle_Applications#Conversation|Conversation]] application example.
 
To add the possibility to answer incoming calls in private using the same DAK, see the [[Toggle_Applications#Conversation|Conversation]] application example.
Line 84: Line 88:
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
−
Action commands:
+
{{Code2|
−
  ''IF %udd(%1.phy)''
+
  IF %udd(%1.phy)
−
  ''$PROG L%1.dir LV''
+
  $PROG L%1.dir LV
−
  ''WUDD %1.phy 0''
+
  WUDD %1.phy 0
−
  ''STOP''
+
  STOP
−
  ''ENDIF''
+
  ENDIF
−
  ''$PROG L%1.dir L801''
+
  $PROG L%1.dir L801
−
  ''WUDD %1.phy 1''
+
  WUDD %1.phy 1
−
<br/>
+
}}
  
 
Stepping through several programs can be performed by using the step codes 790 and 791 configured in the DAK settings:
 
Stepping through several programs can be performed by using the step codes 790 and 791 configured in the DAK settings:
Line 104: Line 108:
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
−
Action commands:
+
{{Code2|
−
  ''IF %op(%sev,=,4)''
+
  IF %op(%sev,<nowiki>=</nowiki>,4)
−
  ''$DD L%1.dir L790''
+
  $DD L%1.dir L790
−
  ''ENDIF''
+
  ENDIF
−
  ''IF %op(%sev,=,5)''
+
  IF %op(%sev,<nowiki>=</nowiki>,5)
−
  ''$DD L%1.dir L791''
+
  $DD L%1.dir L791
−
  ''ENDIF''
+
  ENDIF
−
<br/>
+
}}
  
 
For more details see [[$PROG]] and [[Audio Program]]
 
For more details see [[$PROG]] and [[Audio Program]]
Line 121: Line 125:
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
−
Action commands:
+
{{Code2|
−
  ''IF %udd(%1.phy)''
+
  IF %udd(%1.phy)
−
  ''$TRF L%1.dir ""''
+
  $TRF L%1.dir ""
−
  ''WUDD %1.phy 0''
+
  WUDD %1.phy 0
−
  ''STOP''
+
  STOP
−
  ''ENDIF''
+
  ENDIF
−
  ''$TRF L%1.dir L101''
+
  $TRF L%1.dir L101
−
  ''WUDD %1.phy 1''
+
  WUDD %1.phy 1
−
<br/>
+
}}
  
 
Toggle between '''Call Request Transfer ON''' and '''Call Request transfer OFF'''. The example shows transferring Call Requests to directory number 101.
 
Toggle between '''Call Request Transfer ON''' and '''Call Request transfer OFF'''. The example shows transferring Call Requests to directory number 101.
Line 136: Line 140:
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
−
Action commands:
+
{{Code2|
−
  ''IF %udd(%1.phy)''
+
  IF %udd(%1.phy)
−
  ''$SCRT L%1.dir''
+
  $SCRT L%1.dir
−
  ''WUDD %1.phy 0''
+
  WUDD %1.phy 0
−
  ''STOP''
+
  STOP
−
  ''ENDIF''
+
  ENDIF
−
  ''$SCRT L%1.dir L101''
+
  $SCRT L%1.dir L101
−
  ''WUDD %1.phy 1''
+
  WUDD %1.phy 1
−
<br/>
+
}}
  
 
'''Option:''' If using a station with LED indications on the DAK keys (i.e. CRM-V or ECPIR-3P) the LED can be switched on and off to show status of the transfer. Change the action commands for the transfer event like this: (example shows red LED)
 
'''Option:''' If using a station with LED indications on the DAK keys (i.e. CRM-V or ECPIR-3P) the LED can be switched on and off to show status of the transfer. Change the action commands for the transfer event like this: (example shows red LED)
−
  ''IF %udd(%1.phy)''
+
{{Code2|
−
  ''$TRF L%1.dir ""''
+
  IF %udd(%1.phy)
−
  ''WUDD %1.phy 0''
+
  $TRF L%1.dir ""
−
  '''''IND %1.phy %1.dir(i%2.dir) 1 1 OFF'''''
+
  WUDD %1.phy 0
−
  ''STOP''
+
  '''IND %1.phy %1.dir(i%2.dir) 1 1 OFF'''
−
  ''ENDIF''
+
  STOP
−
  ''$TRF L%1.dir L101''
+
  ENDIF
−
  ''WUDD %1.phy 1''
+
  $TRF L%1.dir L101
−
  '''''IND %1.phy %1.dir(i%2.dir) 1 1 ON'''''
+
  WUDD %1.phy 1
−
<br/>
+
  '''IND %1.phy %1.dir(i%2.dir) 1 1 ON'''
 +
}}
  
 
For more details see [[$TRF]], [[$SCRT]] and [[IND]]
 
For more details see [[$TRF]], [[$SCRT]] and [[IND]]
Line 166: Line 171:
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
−
Action commands:
+
{{Code2|
−
  ''IF %udd(%1.phy)''
+
  IF %udd(%1.phy)
−
  ''$CONF L%1.dir LV''
+
  $CONF L%1.dir LV
−
  ''WUDD %1.phy 0''
+
  WUDD %1.phy 0
−
  ''STOP''
+
  STOP
−
  ''ENDIF''
+
  ENDIF
−
  ''$CONF L%1.dir L8201''
+
  $CONF L%1.dir L8201
−
  ''WUDD %1.phy 1''
+
  WUDD %1.phy 1
−
<br/>
+
}}
  
 
For more details see [[$CONF]]
 
For more details see [[$CONF]]
Line 184: Line 189:
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
−
Action command:
+
{{Code2|
−
  ''$ODC L%1.dir L8301 U2''
+
  $ODC L%1.dir L8301 U2
−
<br/>
+
}}
  
 
For more details see [[$ODC]]
 
For more details see [[$ODC]]
Line 196: Line 201:
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
−
Action commands:
+
{{Code2|
−
  ''IF %op(%vol(%1.phy),=,9)''
+
  IF %op(%vol(%1.phy),<nowiki>=</nowiki>,9)
−
  ''$VOL L%1.dir U0''
+
  $VOL L%1.dir U0
−
  ''STOP''
+
  STOP
−
  ''ENDIF''
+
  ENDIF
−
  ''$VOL L%1.dir U%op(%vol(%1.phy),+,1)''
+
  $VOL L%1.dir U%op(%vol(%1.phy),+,1)
−
<br/>
+
}}
  
 
Alternatively the volume stepping can be in double rate, incrementing the volume by two for each button press:
 
Alternatively the volume stepping can be in double rate, incrementing the volume by two for each button press:
  
−
Action commands:
+
{{Code2|
−
  ''IF %op(%vol(%1.phy),=,9)''
+
  IF %op(%vol(%1.phy),<nowiki>=</nowiki>,9)
−
  ''$VOL L%1.dir U1''
+
  $VOL L%1.dir U1
−
  ''STOP''
+
  STOP
−
  ''ENDIF''
+
  ENDIF
−
  ''$VOL L%1.dir U%op(%vol(%1.phy),+,2)''
+
  $VOL L%1.dir U%op(%vol(%1.phy),+,2)
−
<br/>
+
}}
  
 
Using a station with two buttons (or two inputs) assigning one for volume up, and one for volume down:
 
Using a station with two buttons (or two inputs) assigning one for volume up, and one for volume down:
Line 219: Line 224:
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
−
Action commands:
+
{{Code2|
−
  ''IF %op(%vol(%1.phy),=,9)''
+
  IF %op(%vol(%1.phy),<nowiki>=</nowiki>,9)
−
  ''STOP''
+
  STOP
−
  ''ENDIF''
+
  ENDIF
−
  ''$VOL L%1.dir U%op(%vol(%1.phy),+,1)''
+
  $VOL L%1.dir U%op(%vol(%1.phy),+,1)
−
<br/>
+
}}
  
 
[[File:Toggle Applications 15.PNG|thumb|left|500px|Adjusting volume down when pressing DAK5 (input5)]]
 
[[File:Toggle Applications 15.PNG|thumb|left|500px|Adjusting volume down when pressing DAK5 (input5)]]
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
−
Action commands:
+
{{Code2|
−
  ''IF %op(%vol(%1.phy),=,0)''
+
  IF %op(%vol(%1.phy),<nowiki>=</nowiki>,0)
−
  ''STOP''
+
  STOP
−
  ''ENDIF''
+
  ENDIF
−
  ''$VOL L%1.dir U%op(%vol(%1.phy),-,1)''
+
  $VOL L%1.dir U%op(%vol(%1.phy),-,1)
−
<br/>
+
}}
  
 
For more details see [[VOLUME|VOL]]
 
For more details see [[VOLUME|VOL]]
  
−
[[Category:Applications]]
+
 
 +
[[Category:AlphaCom Applications]]
 +
[[Category: ICX-AlphaCom Applications]]

Latest revision as of 15:16, 31 May 2022

AI.png

This article describes different applications where the common scenario is to toggle a feature on/off using just a DAK key (or station input). Some features have options that gives additional opportunities.

The Station Input or Station DAK key event is the preferred event for most of the applications.

Conversation

Note icon As from AlphaCom v. 13 a call can be toggled on/off from a DAK key by setting the flag Idle DAK during conv. cancel ongoing call. No need to program any events


Toggle between Call and Cancel: pressing DAK key 1 sets up a call to station 101. Second press cancels the call. A second event must be created to handle the scenario where 101 initiates the call , or ends the call.

First DAK key press: Call.
Second press: Cancel


Action commands: 

IF %udd(%1.phy)
$C L%1.dir
WUDD %1.phy 0
STOP
ENDIF
$CALL L%1.dir L101
WUDD %1.phy 1


Adjust UDD if call initiated or ended from the other station


Action commands: 

WUDD %1.phy %chg(1,0)


The same DAK can also answer an incoming call in private mode. Then the following event must be added:

Adjust UDD if call initiated or ended from the other station


Add some commands to the top of the initial DAK as RCI event, making it look like this: Action commands: 

IF %op(%udd(%1.phy),=,2)
$M L%1.dir
pause
$MREL L%1.dir
WUDD %1.phy 1
STOP
ENDIF
IF %udd(%1.phy)
$C L%1.dir
WUDD %1.phy 0
STOP
ENDIF
$CALL L%1.dir L101
WUDD %1.phy 1


For more details see $CALL, $C, $M, $MREL and pause

Call Request

Toggle between Call Request and Cancel Call Request: Pressing the DAK key the first time sends a Call Request to station 101 in the example. Second press cancels the call request. A second event must be created to handle the scenario where 101 answers the call request, or cancels it.

First press: Make a Call Request to 101
Second press: Cancel the Call Request


Action commands: 

IF %udd(%1.phy)
$CANM L%1.dir L101
WUDD %1.phy 0
STOP
ENDIF
$SM L%1.dir L101
WUDD %1.phy 1


Reset UDD when station is no longer in Call Request mode (i.e. the Call Request is for any reason removed)


Action commands: 

WUDD %2.phy 0


To add the possibility to answer incoming calls in private using the same DAK, see the Conversation application example.

For more details see $CANM, $SM and Call Request

Audio Program

Toggle between Program ON and Program OFF. The example shows program 1 (801).

First press: make the station listen to program 1 (801)
Second press: Turn listening to program off


Action commands: 

IF %udd(%1.phy)
$PROG L%1.dir LV
WUDD %1.phy 0
STOP
ENDIF
$PROG L%1.dir L801
WUDD %1.phy 1


Stepping through several programs can be performed by using the step codes 790 and 791 configured in the DAK settings:

790: Step to next program
791: Step to previous program


An event can also be created to do this. The example below uses DAK 4 for stepping to next program, and DAK 5 for stepping to previous program.

DAK4 (or input 4) activated: Step to next program
DAK5 (or input 5) activated: Step to previous program


Action commands: 

IF %op(%sev,=,4)
$DD L%1.dir L790
ENDIF
IF %op(%sev,=,5)
$DD L%1.dir L791
ENDIF


For more details see $PROG and Audio Program

Transfer

Toggle between Transfer ON and Transfer OFF. The example shows transferring calls to directory number 101.

First press: Activate call transfer to 101
Second press: Deactivate transfer


Action commands: 

IF %udd(%1.phy)
$TRF L%1.dir ""
WUDD %1.phy 0
STOP
ENDIF
$TRF L%1.dir L101
WUDD %1.phy 1


Toggle between Call Request Transfer ON and Call Request transfer OFF. The example shows transferring Call Requests to directory number 101.

First press: Activate Call Request transfer to 101
Second press: Deactivate Call Request transfer


Action commands: 

IF %udd(%1.phy)
$SCRT L%1.dir
WUDD %1.phy 0
STOP
ENDIF
$SCRT L%1.dir L101
WUDD %1.phy 1


Option: If using a station with LED indications on the DAK keys (i.e. CRM-V or ECPIR-3P) the LED can be switched on and off to show status of the transfer. Change the action commands for the transfer event like this: (example shows red LED) Action commands: 

IF %udd(%1.phy)
$TRF L%1.dir ""
WUDD %1.phy 0
IND %1.phy %1.dir(i%2.dir) 1 1 OFF
STOP
ENDIF
$TRF L%1.dir L101
WUDD %1.phy 1
IND %1.phy %1.dir(i%2.dir) 1 1 ON


For more details see $TRF, $SCRT and IND

Simplex Conference

Toggle between joining a simplex conference (SX), and leaving it. The example shows joining/leaving SX1 (8201).

First press: Join Simplex Conference 1 (8201)
Second press: Leave the Simplex Conference


Action commands: 

IF %udd(%1.phy)
$CONF L%1.dir LV
WUDD %1.phy 0
STOP
ENDIF
$CONF L%1.dir L8201
WUDD %1.phy 1


For more details see $CONF

Open Duplex Conference

Toggle between joining a open duplex conference (ODC), and leaving it. The example shows joining/leaving ODC1 (8301).

The $ODC command as an inbuilt toggle function, joining or leaving the conference depending on current status


Action commands: 

$ODC L%1.dir L8301 U2


For more details see $ODC

Volume adjustment

Stepping the volume in a circle using just one button. After max volume, the next step is minimum volume.

Activating the DAK (or an input) increments the volume by 1


Action commands: 

IF %op(%vol(%1.phy),=,9)
$VOL L%1.dir U0
STOP
ENDIF
$VOL L%1.dir U%op(%vol(%1.phy),+,1)


Alternatively the volume stepping can be in double rate, incrementing the volume by two for each button press:

Action commands: 

IF %op(%vol(%1.phy),=,9)
$VOL L%1.dir U1
STOP
ENDIF
$VOL L%1.dir U%op(%vol(%1.phy),+,2)


Using a station with two buttons (or two inputs) assigning one for volume up, and one for volume down:

Adjusting volume up when pressing DAK4 (input4)


Action commands: 

IF %op(%vol(%1.phy),=,9)
STOP
ENDIF
$VOL L%1.dir U%op(%vol(%1.phy),+,1)


Adjusting volume down when pressing DAK5 (input5)


Action commands: 

IF %op(%vol(%1.phy),=,0)
STOP
ENDIF
$VOL L%1.dir U%op(%vol(%1.phy),-,1)


For more details see VOL

Retrieved from "https://wiki.zenitel.com/w/index.php?title=Toggle_Applications&oldid=228942"