Difference between revisions of "Message Formats (Sortable)"
From Zenitel Wiki
Line 25: | Line 25: | ||
|[[AUDIO_LINK_NOT_AVAILABLE ]] || align=center | || align=center |0x8006 || Response to AUDIO_PATH_SETUP from next node: Channel not granted | |[[AUDIO_LINK_NOT_AVAILABLE ]] || align=center | || align=center |0x8006 || Response to AUDIO_PATH_SETUP from next node: Channel not granted | ||
|- | |- | ||
− | |[[AUDIO_LINK_OK ]] || align=center |nbsp; || align=center |0x8003|| Response to AUDIO_PATH_SETUP. Channel number is OK | + | |[[AUDIO_LINK_OK ]] || align=center | || align=center |0x8003|| Response to AUDIO_PATH_SETUP. Channel number is OK |
|- | |- | ||
|[[AUDIO_LINK_RELEASE ]] || align=center | || align=center |0x8005 || Used to release audio path backwards stepwise from node to node when setup meets busy or faulty link | |[[AUDIO_LINK_RELEASE ]] || align=center | || align=center |0x8005 || Used to release audio path backwards stepwise from node to node when setup meets busy or faulty link |
Revision as of 10:22, 25 June 2007
Message | Short format | Message id, Hex | Description |
---|---|---|---|
ABSENCE_STATUS | 0x002A | Response to SET_ABSENCE and GET_ABSENCE messages | |
ALARM_MSG | $ALRM | 0x0007 | Set up (or disconnect) an ASVP Alarm message to a single station or a predefined group of stations |
ALARM_MSG_ACK | 0x0009 | Positive response to ALARM_MSG | |
AUDIO_CH_DISCON | 0x8012 | Disconnect a audio channel after loopback test | |
AUDIO_CH_FAULTY | 0x8013 | Response to AUDIO_CH_LOOPBACK_REQ: Requested channel was faulty | |
AUDIO_CH_LOOPBACK_ACK | 0x8011 | Positive acknowledge of AUDIO_CH_LOOPBACK_REQ | |
AUDIO_CH_LOOPBACK_REQ | $ALRM | 0x8010 | Request for loopback audio connection. Used by the Audio Channel Testing process |
AUDIO_CH_TONE_REQ | 0x8015 | Request a peer exchange to put a 500Hz tone on a audio channel | |
AUDIO_DETECT | $VOX | 0x0053 | Triggers the event Simplex_Conference_Audio |
AUDIO_LINK_NOT_AVAILABLE | 0x8006 | Response to AUDIO_PATH_SETUP from next node: Channel not granted | |
AUDIO_LINK_OK | 0x8003 | Response to AUDIO_PATH_SETUP. Channel number is OK | |
AUDIO_LINK_RELEASE | 0x8005 | Used to release audio path backwards stepwise from node to node when setup meets busy or faulty link | |
AUDIO_M_FEED_REQ | 0x801A | Global Simplex Conference: Some station is pressing the M-key when participating in a conference | |
AUDIO_M_FEED_STOP | 0x801B | Global Simplex Conference: The station is releasing the M-key | |
AUDIO_M_LINK_OK | 0x8019 | Per hop positive response to AUDIO_M_PATH_SETUP | |
AUDIO_M_PATH_BACKTRACK | 0x8018 | AUDIO_M_PATH_SETUP failed | |
AUDIO_M_PATH_OK | 0x8017 | Contains statuses for an AUDIO_M_PATH_SETUP from one or more destination exchanges | |
AUDIO_M_PATH_SETUP | 0x8016 | Communication in a multi-node network | |
AUDIO_PATH_CHECK_OK | 0x800F | Positive response to CHECK_AUDIO_PATH | |
AUDIO_PATH_DELAY | 0x8007 | Set Duplex switch delay | |
AUDIO_PATH_DISCONNECT | 0x8006 | Release the endtoend audio path. Normal disconnect from source or destination | |
AUDIO_PATH_OK | 0x8002 | End to end message: Audio path is ready | |
AUDIO_PATH_SETUP | 0x8001 | Set up audio path between a source node and a destination node (possibly via transit nodes) | |
BUILD_GLOB_GRP | 0x0070 | Broadcast message to all exchanges to make them rebuild global group indexes | |
C_KEY | $C | 0x0058 | Order station to press C-key |
CALL_SETUP | $CALL | 0x0008 | Sets up a coversation between two users |
CALL_STATUS_BC | 0x0040 | Broadcast message telling the status of a call | |
CALL_TRANSFER | $TRF | 0x0044 | Set or remove call transfer for a station |
CALL_TRANSFER_NOK | 0x0046 | Negative response to CALL_TRANSFER | |
CALL_TRANSFER_OK | 0x0045 | Positive response to CALL_TRANSFER | |
CANCEL_MAIL | $CANM | 0x0065 | Delete one or more mail/call request/alarm messages queued at a station |
CHECK_AUDIO_PATH | 0x800E | Check of established audio path at regular intervals | |
CLEAR_RCO | $CLR | 0x0015 | Turn the given remote control output off |
CLEAR_RCO_FAILED | 0x0017 | Negative response to the CLEAR_RCO message | |
PULSE_RCO_OK | 0x001C | Positive response to the PULSE_RCO message | |
COMMAND_RESPONSE | 0x0066 | General response message to messages | |
CONF_TALK | $CONF_TALK | 0x008B | Set Simplex conference speaker |
CONF_TALK_STOP | $CONF_TALK_STOP | 0x008C | Stop station form feeding Simplex conference |
PROG_CONF | $CONF | 0x0004 | Set Simplex conference for predefined group of stations or a single station |
CONF_IS_ROOT | 0x007B | Broadcast message. Sender informs that it is root of conference | |
CONF_JOIN | 0x0078 | Exchange wants to join conference, asks root-exchange to setup connection back to sender | |
CONF_MEMB_CHK | 0x0079 | Ask whether any neighbor exchange has any ordinary member left in conference | |
CONF_NOT_ROOT | 0x007C | Broadcast message. Sender informs that it is no longer root of conference | |
CONF_ORD_MEMB | 0x007A | An exchange tells its neighbors that it has ordinary member left in conference | |
AUDIO_LINK_OK | 0x8003 | Response to AUDIO_PATH_SETUP. Channel number is OK | |
AUDIO_M_FEED_REQ | 0x801A | Global Simplex Conference: Some station is pressing the M-key when participating in a conference | |
AUDIO_M_FEED_REQ | 0x801A | Global Simplex Conference: Some station is pressing the M-key when participating in a conference | |
AUDIO_LINK_OK | 0x8003 | Response to AUDIO_PATH_SETUP. Channel number is OK | |
AUDIO_M_FEED_REQ | 0x801A | Global Simplex Conference: Some station is pressing the M-key when participating in a conference | |
AUDIO_M_FEED_REQ | 0x801A | Global Simplex Conference: Some station is pressing the M-key when participating in a conference | |
AUDIO_LINK_OK | 0x8003 | Response to AUDIO_PATH_SETUP. Channel number is OK | |
AUDIO_M_FEED_REQ | 0x801A | Global Simplex Conference: Some station is pressing the M-key when participating in a conference | |
AUDIO_M_FEED_REQ | 0x801A | Global Simplex Conference: Some station is pressing the M-key when participating in a conference | |
AUDIO_LINK_OK | 0x8003 | Response to AUDIO_PATH_SETUP. Channel number is OK |