Actions

Main Settings - Edge Controller: Difference between revisions

From Zenitel Wiki

(Created page with "{{E}} This article describes how to configure a Turbine device as an '''Edge Controller'''. {{note|You can do all configuration of your devices from the EDGE Controller. The...")
 
No edit summary
 
(35 intermediate revisions by 2 users not shown)
Line 1: Line 1:
{{E}}
{{E}}
This article describes how to configure a Turbine device as an '''Edge Controller'''.  
This article describes how to configure a Zenitel IP device to act as an '''[[Edge Controller]]'''.  


{{note|You can do all configuration of your devices from the EDGE Controller. There is no need to log on to each device }}
{{note|  
* ''Most Zenitel IP devices can act as an Edge Controller, see [[Edge Controller|full list here]]''
* ''You can do all configuration of your devices from the Edge Controller. There is no need to log on to each device''
* ''The Edge Controller should use a Static IP Address, not obtain IP address from a DHCP server'' }}


 
* [[Logging into an IP Station|Logging on to the device you will use as the Edge Controller]]
* [[Logging into an IP Station|Logging on to the device you will use as the EDGE Controller]]
* Select '''Main''' > '''Main Settings''' to access the page for configuring Mode of operation and Network Settings.
* Click '''Station Main > Main Settings''' to access the page for configuring station mode and Network Settings.
[[File:Edge MainSettings2.PNG|thumb|left|700px|Setting the Edge Controller]]
[[File:SIP-MainSettings.PNG|thumb|left|500px]]
<br style="clear:both;" />
<br style="clear:both;" />


'''Station Mode:''' Select one of the available modes: AlphaCom, Exigo, SIP, Pulse and Pulse Server.
'''Mode:''' Select the mode ''Edge Controller''


'''Product Model And Accessory [Turbine only]:''' Depending on the type of Turbine hardware, there are different Product models and accessories to choose from. Find your model here: [[:Category:Stations#Turbine_stations|Turbine Station Models]]
'''Product Model And Accessory:''' Depending on the type of Turbine hardware, there are different Product models and accessories to choose from. Find your model here: [[:Category:Stations#Turbine_stations|Turbine Station Models]]


'''IP Settings:'''
'''IP Settings:'''
* '''DHCP''' – Select this option if the IP station shall receive IP Settings from a DHCP server.
* '''Static IP''' – The Edge Controller must be assigned a Static IP address. Enter values for:
* '''Static IP''' – Select this option if the IP station shall use a static IP address. Enter values for:
** '''IP-address'''
::- '''IP-address'''
** '''Subnet-mask'''
::- '''Subnet-mask'''
** '''Gateway''': The controller must have a valid Default Gateway address defined.
::- '''Gateway'''
*** If there is no gateway in the network, you can enter the same IP Address as the Static IP Address. A valid gateway address is important for the [[Group Call (Edge)|Group Call feature]].
::- '''DNS Server 1''' (option for network administration)
** '''DNS Server 1''': (option for network administration)
::- '''DNS Server 2''' (option for network administration)
** '''DNS Server 2''': (option for network administration)
::- '''Hostname''' (option for network administration)
** '''Hostname''': (option for network administration)
 
* '''Disable Reset to Factory default settings using frontboard and I/O  [Turbine only]:''' If enabled, factory reset will only be possible from StationWeb. This is disabled by default.
 
*'''Read IP Address  [Turbine only]:''' Check the '''Read IP Address''' box to enable an unregistered station to speak the IP address when the call button is pressed. "Read IP Address" is default enabled.
 
*'''Enable RSTP  [Turbine only]''' (for Industrial & Ex stations): Check the '''Enable RSTP''' box to enable RSTP. RSTP is only required when using redundant networking
 
*'''Ethernet Speed 10 Mbits/s [Turbine only]''': Enable in some rare cases where it is not convenient to use 100 MBit/s Ethernet speed. Default Ethernet speed is 100 Mbit/s unless switch is configured to 10 Mbit/s.
 
*'''Use Last IP On DHCP failure [INCA only]:''' If the station does not receive an IP Address from a DHCP server at startup, it will use the last IP address.


*'''IGMP Version [INCA only]:''' Select IGMPv2 or IGMPv3 for multicast group membership.
* '''Disable Reset to Factory default settings using frontboard and I/O :''' If enabled, factory reset will only be possible from StationWeb. This is disabled by default.
*'''Read IP Address:''' When enabled an unregistered station will speak its IP address when the call button is pressed. "Read IP Address" is default enabled.
*'''Enable RSTP''' (for Industrial & Ex stations): Check the '''Enable RSTP''' box to enable Rapid Speanning Tree Protocol RSTP. RSTP is only required when using redundant networking
*'''Ethernet Speed 10 Mbits/s''': Enable in some rare cases where it is not convenient to use 100 MBit/s Ethernet speed. Default Ethernet speed is 100 Mbit/s unless switch is configured to 10 Mbit/s.
*'''IGMP Version [Desktop v2, IP FlushMaster v2 and IP-CROR v2 only]:''' Select IGMPv2 or IGMPv3 for multicast group membership.


Click '''Save''' followed by '''Apply''' to apply the new configuration settings.
Click '''Save''' to apply the new configuration settings.


[[Category: Pulse - Configuration]]
[[Category: IC-EDGE Configuration]]
[[Category: SIP intercom - Configuration]]

Latest revision as of 12:14, 12 January 2024

Edge-icon.jpg

This article describes how to configure a Zenitel IP device to act as an Edge Controller.

Note icon
  • Most Zenitel IP devices can act as an Edge Controller, see full list here
  • You can do all configuration of your devices from the Edge Controller. There is no need to log on to each device
  • The Edge Controller should use a Static IP Address, not obtain IP address from a DHCP server


Setting the Edge Controller


Mode: Select the mode Edge Controller

Product Model And Accessory: Depending on the type of Turbine hardware, there are different Product models and accessories to choose from. Find your model here: Turbine Station Models

IP Settings:

  • Static IP – The Edge Controller must be assigned a Static IP address. Enter values for:
    • IP-address
    • Subnet-mask
    • Gateway: The controller must have a valid Default Gateway address defined.
      • If there is no gateway in the network, you can enter the same IP Address as the Static IP Address. A valid gateway address is important for the Group Call feature.
    • DNS Server 1: (option for network administration)
    • DNS Server 2: (option for network administration)
    • Hostname: (option for network administration)
  • Disable Reset to Factory default settings using frontboard and I/O : If enabled, factory reset will only be possible from StationWeb. This is disabled by default.
  • Read IP Address: When enabled an unregistered station will speak its IP address when the call button is pressed. "Read IP Address" is default enabled.
  • Enable RSTP (for Industrial & Ex stations): Check the Enable RSTP box to enable Rapid Speanning Tree Protocol RSTP. RSTP is only required when using redundant networking
  • Ethernet Speed 10 Mbits/s: Enable in some rare cases where it is not convenient to use 100 MBit/s Ethernet speed. Default Ethernet speed is 100 Mbit/s unless switch is configured to 10 Mbit/s.
  • IGMP Version [Desktop v2, IP FlushMaster v2 and IP-CROR v2 only]: Select IGMPv2 or IGMPv3 for multicast group membership.

Click Save to apply the new configuration settings.

Retrieved from "https://wiki.zenitel.com/w/index.php?title=Main_Settings_-_Edge_Controller&oldid=235474"
MediaWiki spam blocked by CleanTalk.